Dodge - Neon - Owners Manual - 2005 - 2005

TABLE OF CONTENTS SECTION PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES 7 MAINTAINING YOUR VEHICLE 8 MAINTENANCE SCHEDULES 9 IF YOU NEED CONSUMER ASSISTANCE 10 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233 10 I nf or mat i onPr ov i dedby : I nf or mat i onPr ov i dedby : INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . 6 m How To Use This Manual . . . . . . . . . . . . . . . . . 4 m Vehicle Modifications / Alterations . . . . . . . . . . 6 m Warnings And Cautions . . . . . . . . . . . . . . . . . . 6 I nf or mat i onPr ov i dedby : 1 4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle. NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings. When it comes to service, remember that your dealer knows your vehicle best, has the factory-trained technicians and genuine Mopart parts, and is interested in your satisfaction. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. HOW TO USE THIS MANUAL Consult the table of contents to determine which section contains the information you desire. The detailed index, at the rear of this manual, contains a complete listing of all subjects. Consult the following table for a description of the symbols that may be used on your vehicle or throughout this owner’s manual: I nf or mat i onPr ov i dedby : INTRODUCTION 5 1 I nf or mat i onPr ov i dedby : 6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER Vehicle Identification Number (VIN) is found on a laser etched plate, located on the left front corner of the instrument panel, visible through the windshield. This number also appears on the vehicle registration or title. Vehicle Identification Number VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . 9 ▫ Automatic Transaxle Ignition Interlock System . .14 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . . 9 m Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ Locking Doors With The Key . . . . . . . . . . . . . .10 ▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . .14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .11 ▫ Power Door Locks — If Equipped . . . . . . . . . .15 m Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 ▫ Central Locking/Unlocking — If Equipped . . . .15 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . . .12 ▫ Automatic Door Locks — If Equipped . . . . . . .16 ▫ Sentry Key Programming . . . . . . . . . . . . . . . . .12 ▫ Child-Protection Door Lock System (Rear Doors) .17 ▫ General Information . . . . . . . . . . . . . . . . . . . .13 m Internal Emergency Trunk Lid Release . . . . . . .18 m Steering Wheel Lock — If Equipped . . . . . . . . .13 m Remote Trunk Lid Release — If Equipped . . . . .18 ▫ To Manually Lock The Steering Wheel . . . . . . .13 m Remote Keyless Entry — If Equipped . . . . . . . .19 ▫ To Release The Steering Wheel Lock . . . . . . . . .13 ▫ To Unlock The Doors . . . . . . . . . . . . . . . . . . .19 I nf or mat i onPr ov i dedby : 8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . .19 ▫ Adjustable Upper Shoulder Belt Anchorage . . . .28 ▫ Horn Chirp Feature . . . . . . . . . . . . . . . . . . . . .19 ▫ Lap/Shoulder Belt Untwisting Procedure . . . . .29 ▫ To Unlock The Trunk . . . . . . . . . . . . . . . . . . . .20 ▫ Seat Belts And Pregnant Women . . . . . . . . . . . .30 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .20 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .31 ▫ Programming Additional Transmitters . . . . . . . .20 ▫ Driver And Front Passenger Supplemental Restraint System (SRS) - Airbags . . . . . . . . . . .31 ▫ General Information . . . . . . . . . . . . . . . . . . . .21 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .39 ▫ Transmitter Battery Service . . . . . . . . . . . . . . .21 m Vehicle Theft Alarm — If Equipped . . . . . . . . . .22 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .22 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .23 ▫ Transporting Pets . . . . . . . . . . . . . . . . . . . . . .45 m Engine Break-In Recommendations . . . . . . . . . .46 m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 ▫ Security System Manual Override . . . . . . . . . . .23 m Power Windows — If Equipped . . . . . . . . . . . .23 m Occupant Restraints . . . . . . . . . . . . . . . . . . . . .24 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .24 I nf or mat i onPr ov i dedby : ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .46 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .47 ▫ Periodic Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . .47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9 A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. 2 The double sided keys may be inserted into the locks with either side up. Ignition Key Positions Vehicle Key Ignition Key Removal Automatic Transaxle Place the shift lever in PARK and make sure that the shift knob push button has returned to the out position. Turn the key to the OFF position, turn to the lock position, and remove the key. NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the key cylinder. If this occurs, rotate the key clockwise slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. I nf or mat i onPr ov i dedby : 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Manual Transaxle Depress and hold the release button located between the ignition switch and the instrument panel. Turn the ignition key to LOCK and remove the key. WARNING! Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. Ignition Key Release Button Locking Doors With The Key You can insert the key with either side up. To lock the door, turn the key rearward. To unlock the door, turn the key forward. See Section 7, Body Mechanism Lubrication of this manual for external lock lubrication. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition switch, sounds a signal to remind you to remove the key. immediately after the ignition switch is turned on for a bulb check. Afterwards, if the bulb remains on, this indicates a problem with the electronics. NOTE: With the driver’s door open, and the key in the ignition, the power door locks will not lock via the interior door lock switch. If the bulb begins to flash after the bulb check, this indicates that an invalid key has been used to start the vehicle. Both of these conditions will result in the engine being shut off after two (2) seconds of running. SENTRY KEY The Sentry Key Immobilizer System prevents unauthorized operation of the vehicle by disabling the engine. The system will shut the engine off after 2 seconds of running if an invalid key is used to start the vehicle. This system utilizes ignition keys which have an electronic chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked. During normal operation, the Theft Alarm/ Immobilizer Light will come on for three (3) seconds Keep in mind that a key which has not been programmed is also considered an invalid key even if it is cut to fit the ignition lock cylinder for that vehicle. If the Theft Alarm/Immobilizer Light comes on during normal vehicle operation (vehicle has been running for longer than 10 seconds), a fault has been detected in the electronics and the vehicle should be serviced as soon as possible. NOTE: • The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. I nf or mat i onPr ov i dedby : 2 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (transponder) fault unless the additional part is physically held against the ignition key being used when starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system. All of the keys provided with your new vehicle have been programmed to the vehicle electronics. consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to the dealer. Sentry Key Programming You can program new keys to the system if you have two valid sentry keys by performing the following procedure: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure 2. Insert the first valid key into the ignition switch and turn the ignition switch ON for at least 3 seconds but no longer than 15 seconds. Turn the ignition switch OFF and remove the first key. 3. Insert the second valid key and turn the ignition switch ON within 15 seconds. After ten seconds a chime will sound and the Theft Alarm Light will begin to flash. Turn the ignition switch OFF and remove the second key. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed. Repeat this procedure to program up to a total of 8 keys. If you do not have a programmed sentry key, contact your dealer for details. General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation. 13 STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle without the ignition key. If the steering wheel is rotated no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock. To manually lock the steering wheel: With the engine running, rotate the steering wheel 1/2 turn, turn off the engine and remove the key. Turn the steering wheel slightly in either direction until the lock engages. To release the steering wheel lock: Insert the key in the ignition switch and start the engine. If the key is difficult to turn, rotate the wheel slightly to the right or left to disengage the lock. NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it. I nf or mat i onPr ov i dedby : 2 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK and the shift knob push-button is fully released. It also prevents shifting out of PARK unless the key is in the ON/RUN or START positions and you have depressed the brake pedal. DOOR LOCKS Manual Door Locks All doors are equipped with a rocker-type interior door lock. To lock a door when leaving your vehicle, press the rocker switch to the LOCK position and close the door. NOTE: To avoid accidentally locking your keys in the vehicle, make sure you have them with you before closing any door. CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. I nf or mat i onPr ov i dedby : WARNING! For personal security, and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. 15 Power Door Locks — If Equipped A power door lock switch is on each front door panel. Press this switch to lock or unlock the doors. Central Locking/Unlocking — If Equipped All vehicle doors are locked with the first turn of the key to the LOCK position. The double activation feature requires you to turn the key in the cylinder lock two times within five seconds to UNLOCK all vehicle doors at once. You may disable this feature and unlock all the doors with one turn of the key by performing the following procedure: NOTE: Steps 2 and 3 must be completed within 10 seconds. 1. Close all doors and place the key in the ignition switch. 2. Cycle the ignition switch ON/OFF four times ending in the OFF position. Door Lock Switches 3. Press the interior door lock switch to the UNLOCK position. I nf or mat i onPr ov i dedby : 2 16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. A single chime will sound to signify that you have successfully disabled the double activation feature. You can turn the feature back on by repeating the above mentioned procedure. You can turn the feature back on by repeating the above mentioned procedure. Automatic Door Locks — If Equipped The doors will lock automatically if: 1. Close all doors and place the key in the ignition switch. 2. Cycle the ignition switch ON/OFF four times ending in the OFF position. 3. Press the interior door lock switch to the LOCK position. 4. A single chime will sound to signify that you have successfully completed the programming. 1. all doors are closed, You can turn the feature back on by repeating the above mentioned procedure. 2. vehicle speed is above 15 mph (24 km/h), 3. the accelerator pedal is depressed. The Automatic Door Locks can be enabled or disabled by performing the following procedure: NOTE: Steps 2 and 3 must be completed within 10 seconds. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child-Protection Door Lock System (Rear Doors) 17 WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: For emergency exit with the system engaged, move the door lock rocker switch to the UNLOCK position, roll down the window and open the door with the outside door handle. Child Lock Control To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the childprotection door lock system. To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position. I nf or mat i onPr ov i dedby : 2 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE INTERNAL EMERGENCY TRUNK LID RELEASE WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat. If trapped in the trunk, children can die from suffocation or heat stroke. Emergency Release As a security measure, a Trunk Internal Emergency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark lever attached to the trunk latching mechanism. See picture below. REMOTE TRUNK LID RELEASE — IF EQUIPPED You can open the trunk from inside the vehicle by pressing a switch located inside the glove compartment. NOTE: The remote trunk release feature will operate with the ignition switch in all positions. The remote trunk release will not operate above 5 mph. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY — IF EQUIPPED This system allows you to lock or unlock the doors and trunk or activate the panic alarm from distances up to about 23 feet (7 meters) using a hand held transmitter. 19 NOTE: You may turn off this feature and unlock all doors with one press of the button by following the procedure shown in the Central Locking/Unlocking paragraph. To Lock the Doors Press and release the LOCK button to lock all doors. The park/lamps will flash and the horn will chirp to acknowledge the signal. Four Button Transmitter NOTE: A slight delay of up to two seconds can occur before the doors or trunk will unlock. To Unlock the Doors Press and release the UNLOCK button once to unlock the driver’s door. Press the button twice within 5 seconds to unlock all doors. The interior lights also come on and remain on for about 30 seconds when you unlock the doors. Horn Chirp Feature The horn chirp that signals that the doors have been locked can be toggled on or off by using the following procedure: 1. Insert the ignition key and turn the switch to the ON/RUN position. 2. Press and hold the UNLOCK button on the transmitter for 4 to 10 seconds. 3. Continue to hold the UNLOCK button and press the LOCK button. 4. Release both buttons. I nf or mat i onPr ov i dedby : 2 20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A chime will sound to signify that the feature has been successfully completed. To Unlock the Trunk Press the TRUNK button on the transmitter twice to unlock the trunk. NOTE: A slight delay of up to two seconds can occur before the trunk unlatches. Using The Panic Alarm To turn on the panic alarm feature, press and release the PANIC button. When the panic alarm is on the headlights and park/lamps will flash, the horn will pulse on and off and the interior lights will turn on. The panic alarm will stay on for 3 minutes unless you press the PANIC button a second time, or until vehicle speed reaches 15 mph (24 km/h). NOTE: When you turn off the panic alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system. Programming Additional Transmitters Up to four transmitters can be programmed to your vehicle. Your new vehicle was shipped with two transmitters. See your dealer for additional transmitters. Additional transmitters can be programmed to the system by using the following procedure: 1. Insert the key into the ignition and turn the switch to the RUN position. 2. Press and hold the UNLOCK button on the transmitter for between four and ten seconds. 3. Continue to hold the UNLOCK button and press the PANIC button. A chime will sound to indicate that the transmitter programming mode has been entered. 4. Press a button on all transmitters to be programmed to the system, including any previously programmed transmitters. A chime will sound when each transmitter has been programmed. 5. Turn the ignition switch off to exit the transmitter programming mode. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be received, including interference that may cause undesired operation. 21 1. With the transmitter buttons facing down, use a thin coin or similar object to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. If your transmitter fails to operate from a normal distance, check for these two conditions. 1. Weak batteries in transmitter. The expected life of batteries is from one to two years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. Transmitter Battery Service The recommended replacement battery is 2016 or its equivalent. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. Separating Transmitter Halves 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. I nf or mat i onPr ov i dedby : 2 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To reassemble the transmitter case, snap two halves together. Make sure there is an even gap between the two halves. Test transmitter operation. To set the alarm: VEHICLE THEFT ALARM — IF EQUIPPED The system monitors the doors, trunk key cylinder (Fleet Vehicles Only) , trunk latch (Regular Production Vehicles Only) , and ignition for unauthorized operation. 2. Lock the door using either the door key, power door lock switch, or the Keyless Entry Transmitter and close all doors. If something triggers the alarm, the system will signal for about 18 minutes. For the first 3 minutes the horn will sound and the headlights, park/turn signal lights, tail lights and the indicator light in the cluster will flash. Then the exterior lights will flash for another 15 minutes. If the monitored system which triggered the alarm is deactivated, the alarm will continue to sound until 3 minutes of alarm time is reached. If the monitored system which triggered the alarm is deactivated after the alarm has been on for 3 minutes, the alarm will shut off immediately. 1. Remove the keys from the ignition switch and get out of the vehicle. 3. The indicator light in the instrument cluster will flash rapidly for 16 seconds. This shows that the system is arming. During this period, if a door is opened, the ignition switch is turned on, or the power door locks are unlocked in any manner, the system will automatically disarm. If the light comes on but does not flash, the system is arming but there is a problem in the trunk circuit. After 16 seconds the indicator light will flash slowly. This shows that the system is fully armed. Vehicles equipped with the Sentry Key Immobilizer System can be safely started with a valid key. A valid key is one that is programmed to that particular vehicle. A valid key will disarm the system, an invalid key will trigger the alarm. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: With the system armed on vehicles built for Fleet Service , the trunk can be opened with the key without sounding the Theft Alarm. With the system armed on Regular Production Vehicles , opening the trunk with the key will cause the Theft Alarm to sound. 23 POWER WINDOWS — IF EQUIPPED The window switches on the driver’s door panel control both front windows. The switch on the passenger’s door panel controls the passenger’s window. To disarm the system: Unlock a front door using either the key or the Keyless Entry Transmitter. Starting the vehicle with a valid Sentry key will disarm the system. Tamper Alert If the horn sounds 3 times when you unlock a front door using either a key or the Keyless Entry Transmitter, the alarm has been activated. Check the vehicle for tampering. Security System Manual Override The system will not arm if you lock the doors using the manual lock control. I nf or mat i onPr ov i dedby : Power Window Switches 2 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and side airbags for both the driver and front passenger. If you will be carrying children too small for adult-size belts, your seat belts also can be used to hold infant and child restraint systems. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All the seats in your vehicle are equipped with Lap/ Shoulder Belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce your risk of striking the inside of the vehicle or being thrown out. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Lap/Shoulder Belt Operating Instructions WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or lap belt for more than one person, no matter what their size. 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. Latch Plate I nf or mat i onPr ov i dedby : 2 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. Latch Plate To Buckle I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 27 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. Removing Slack From Belt 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. I nf or mat i onPr ov i dedby : 2 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.). Adjustable Upper Shoulder Belt Anchorage In the driver and front passenger seats, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push up or down on the anchorage button to release the anchorage, and then move it up or down to the position that serves you best. Adjusting Upper Shoulder Belt As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 29 1. Position the latch plate as close as possible to the anchor point. 2 Positioning Latch Plate Twisted Seat Belt I nf or mat i onPr ov i dedby : 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 inches above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. Sliding The Latch Plate 4. Continue to slide the latch plate up until it clears the folded webbing. Creating A Fold 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender and store it. 31 Driver and Front Passenger Supplemental Restraint System (SRS) - Airbags This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers. WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Front Airbag Components I nf or mat i onPr ov i dedby : 2 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. Side Airbags NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. I nf or mat i onPr ov i dedby : WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • If your vehicle is equipped with side airbags, do not use accessory seat covers or place objects between you and the side airbags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. • If your vehicle is equipped with side airbags, do not attach cup holders or any other objects on or around the door. The inflating side airbag could drive the objects into occupants, causing serious injury. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions. If your vehicle is equipped, the side airbag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should always ride buckled up in a rear seat. Infants in rear facing child restraints (designed for children up to 20 lbs (9 kg) and less than one year old) should 33 NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment could cause severe injury or death to infants in that position. Children that are not big enough to properly wear the vehicle seat belt (see Section on Child Restraints) should be secured in the rear seat in child restraints or beltpositioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint. See the section on Child Restraint. You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should wear their lap and shoulder belts properly. I nf or mat i onPr ov i dedby : 2 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. Airbag System Components The front airbag system consists of the following: 4. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the space between you and the door. • AIRBAG Readiness Light • Airbag Control Module (ACM) • Driver Airbag • Passenger Airbag WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • If the vehicle has side airbags, they also need room to inflate. Do not lean against the door. Sit upright in the center of the seat. • Steering Wheel and Column • Instrument Panel • Crash Sensor • Interconnecting Wiring • Knee Impact Bolsters The side airbag system, if equipped, consists of the following: • AIRBAG Readiness Light (shared with the front airbag system) • Side Airbag in the Driver’s Seat • Side Airbag in the Passenger’s Seat I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Right and Left Side Impact Airbag Control Modules (SIACM) • Interconnecting Wiring How The Airbag System Works Front Airbag System 35 • The Airbag Control Module also turns on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition switch is first turned to ON/RUN, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously. • The front Airbag Control Module determines if a frontal collision is severe enough to require the airbags to inflate. • The Airbag Control Module is not designed to detect side, roll over, or rear collisions. • The Airbag Control Module also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON/RUN positions. These include all of the items listed above except the knee bolsters, the instrument panel, and the steering wheel and column. If the key is in the OFF position, in the ACC position, or not in the ignition switch, the airbags are not on and will not inflate. I nf or mat i onPr ov i dedby : Airbag Light 2 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • When the Airbag Control Module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in about 50 milliseconds. This is only about half of the time it takes you to blink your eyes. The airbags then quickly deflate while helping to restrain the driver and front passenger. The driver’s front airbag gas is vented through the airbag material towards the instrument panel. The passenger’s front airbag gas is vented through vent holes in the sides of the airbag. In this way the airbags do not interfere with your control of the vehicle. • The knee impact bolsters help protect the knees and position you for the best interaction with the front airbag. If A Deployment Occurs The airbag system is designed to deploy when the Airbag Control Module detects a moderate-to-severe frontal collision, to help restrain the driver and front passenger, and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you have not healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. 37 Side Airbag System — If Equipped • The Side Impact Airbag Control Modules determine if a side collision is severe enough to require the airbag to inflate. The Side Impact Airbag Control Modules is not designed to detect roll over, front, or rear impacts. • The Side Impact Airbag Control Module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON/RUN positions. These include all of the items listed above. If the left or right SIACM detects a malfunction in any part of the system, it will send a message to the frontal ACM to turn the Airbag Light on. The Airbag Control Module also turns on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition switch is first turned on as a diagnostic or system check, then turns the light off. WARNING! Deployed airbags can’t protect you in another collision. Have the airbags replaced by an authorized dealer as soon as possible. I nf or mat i onPr ov i dedby : 2 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered by the appropriate SIACM, releasing a quantity of nontoxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door. The side airbag moves at a very high speed and with such a high force, that it could injure you if you are not seated properly, or if items are positioned in the area where the side airbag inflates. This especially applies to children. Maintaining Your Airbag Systems Enhanced Accident Response Time — If Equipped If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. In addition, approximately 10 seconds after the vehicle has stopped moving, the interior lights will light until the ignition switch is turned off. I nf or mat i onPr ov i dedby : WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame. • You need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolster. • It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has airbags. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately: 39 Children 12 years and under should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats, rather than in the front. • The AIRBAG light does not come on or flickers during the 6 to 8 seconds when the ignition switch is first turned on. • The light remains on or flickers after the 6 to 8 second interval. • The light flickers or comes on and remains on while driving. Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. I nf or mat i onPr ov i dedby : WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size. 2 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’s Manual to ensure you have the right seat for your child. Use the restraint that is correct for your child: • Safety experts recommend that children ride rearwardfacing in the vehicle until they are at least one year old and weigh at leas 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and “convertible” child seats. Both types of child restraints are held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “Convertible” child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with the front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. • The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back; they should use a Belt Positioning Booster Seat. The child and booster seat are held in the vehicle by the lap/shoulder belt. (Some booster seats are equipped with a front shield and are held in the vehicle by the lap portion.) I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For additional www.seatcheck.org. information refer Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it. to WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing infant restraint should only be used in a rear seat. A rearward facing infant restraint in the front seat may be struck by a deploying passenger airbag which may cause severe or fatal injury to the infant. Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety 41 • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. The passenger seat belts are equipped with cinching latch plates which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate I nf or mat i onPr ov i dedby : 2 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. • If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. without using the vehicle seat belt. All three rear seating positions have exclusive lower anchorages. These are round bars, located at the rear of the seat cushion where it meets the seat back, and just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the surfaces. The lower strap hooks are passed over the top of each bar, pushing aside the seat cover material. • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seat backs and cause serious personal injury. LATCH —L ower Anchors and Tether for CHildren Your vehicle’s rear seat is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for Children. The LATCH system provides for the installation of the child restraint I nf or mat i onPr ov i dedby : Latch Anchorages THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In addition, there are tether strap anchorages behind each rear seating position located in the panel between the rear seat back and the rear window — under a hinged plastic cover with this symbol on it. (Shown to the left) In recent years, only the tether anchorage has been provided in new vehicles. To attach a child restraint tether strap: 1. Lift the cover over the anchor directly behind the seat where you are placing the child restraint. 43 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint and, where possible, route the tether strap under the head restraint and between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Tether Strap Mounting I nf or mat i onPr ov i dedby : 2 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchorages will continue to have features for installation in vehicles using the lap or lap/shoulder belt. They will also have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle. Installing the Child Restraint System While there are LATCH anchorages at all three rear seating positions, do not install child restraints at all three positions at the same time. The anchorages are not designed to restrain three child restraints at one time. Instead, you may install one child restraint at the center position, or two child restraints at the right and left positions. WARNING! Do not install child restraint systems equipped with LATCH attachments at all three rear seating positions at one time. The LATCH anchorages are designed to restrain no more than two child restraints at a time in the event of a collision. We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector and a means for adjusting the tension in the strap. Forward-facing toddler restraints and some rearward-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three straps as you push the child restraint rearward and downward into the seat. Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat. Not all child restraint systems will be installed as we have described here. Again, carefully follow the instructions that come with the child restraint system. • Make sure that the child is upright in the seat. NOTE: If your child restraint seat is not LATCH compatible, install the restraint using the vehicle seat belts. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • The lap portion should be low on the hips and as snug as possible. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. I nf or mat i onPr ov i dedby : 2 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS The engine in your new vehicle does not require a long break-in period. SAFETY TIPS Exhaust Gas WARNING! Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided. The crankcase oil installed in the engine at the factory is a high quality energy conserving type lubricant. Oil changes should be consistent with expected climate conditions under which vehicle operations will occur. The recommended viscosity and quality grades are in Section 7 of this manual. Do not use non-detergent or straight mineral oils. A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and not an indication of a problem. Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. To avoid drawing exhaust gases into the vehicle, close the trunk while driving. However, if for some reason it must remain open, close all windows. Adjust the heating or cooling system to force outside air into the vehicle. Set the blower at high speed. I nf or mat i onPr ov i dedby : THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt. Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the bulb is not lit during starting, have it replaced. If the light stays on or comes on while driving, have the system checked by an authorized dealer. 47 Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness, and tires (including spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if gasoline fumes are present, the cause should be corrected immediately. Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. I nf or mat i onPr ov i dedby : 2 I nf or mat i onPr ov i dedby : UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 m To Open And Close The Hood . . . . . . . . . . . . .58 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .51 m Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 ▫ Inside Compass/Temperature Mirror— If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .51 ▫ Front Map/Reading Lights — If Equipped . . . .60 ▫ Outside Mirror — Driver’s Side . . . . . . . . . . . .54 ▫ Outside Mirror — Passenger’s Side . . . . . . . . . .54 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . . .60 ▫ Multi-Function Control Lever . . . . . . . . . . . . . .61 ▫ Electric Remote-Control Mirrors — If Equipped . .55 ▫ Headlights, Parking Lights, Instrument Panel Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 m Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 ▫ Daytime Running Lights (Canada Only) . . . . . .62 ▫ Front Seat Adjustment . . . . . . . . . . . . . . . . . . .55 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . .62 ▫ Reclining Bucket Seats . . . . . . . . . . . . . . . . . . .56 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . .62 ▫ Adjustable Head Restraints . . . . . . . . . . . . . . .57 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . .62 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . .57 ▫ Headlight Dimmer Switch . . . . . . . . . . . . . . . .62 I nf or mat i onPr ov i dedby : 50 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . .62 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . .66 m Windshield Wipers And Washers . . . . . . . . . . .63 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . .66 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . . .63 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . . .66 ▫ Mist Function . . . . . . . . . . . . . . . . . . . . . . . . .63 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . .67 ▫ Intermittent Wiper System . . . . . . . . . . . . . . . .64 ▫ To Accelerate For Passing . . . . . . . . . . . . . . . .67 ▫ Lo Speed Wipers . . . . . . . . . . . . . . . . . . . . . . .64 m Power Sunroof — If Equipped . . . . . . . . . . . . .68 ▫ Hi Speed Wipers . . . . . . . . . . . . . . . . . . . . . . .64 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . . .69 m Tilt Steering Column . . . . . . . . . . . . . . . . . . . . .64 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . .69 m Electronic Speed Control — If Equipped . . . . . .65 m Console Features . . . . . . . . . . . . . . . . . . . . . . .70 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . .65 ▫ Ash Receiver And Cigar Lighter . . . . . . . . . . . .70 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . . .66 I nf or mat i onPr ov i dedby : UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). 51 Inside Compass/Temperature Mirror—If Equipped Adjust the mirror to center the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustments. Annoying headlight glare can be reduced by rotating the small knob under the mirror in the clockwise direction, so the knob points to the right (night position). The mirror should be adjusted while set in the day position (knob points towards rear of vehicle.) Adjusting Rear View Mirror Adjusting Rear View Mirror I nf or mat i onPr ov i dedby : 3 52 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights • Briefly press the “Right” button to toggle the right reading lamp “ON/OFF”. Repeat the key press to cycle the light • Briefly press the “Left” button to toggle the left reading lamp “ON/OFF”. Repeat the key press to cycle the light. NOTE: The light can be activated with the ignition off. NOTE: The light(s) will automatically shut off after seven minutes with ignition off. Temperature Press and hold the “Right” button for 5–10 seconds (until °F/°C toggles in the display) then release the button. Repeat the key press to cycle the °F/°C in the display. Automatic Dimming Mirror Display ON/OFF Press and hold the “Right” button for 10–15 seconds (until display toggles ON/OFF) then release the button. Repeat the key press to cycle the display ON/OFF. NOTE: The display will default “ON” at each new ignition cycle. I nf or mat i onPr ov i dedby : UNDERSTANDING THE FEATURES OF YOUR VEHICLE 53 Compass Variance • Find your current location and determine the correct Zone number from the map. • Press and hold the “Left” button for 5–10 seconds (until “Zone” appears in the display), then release the button. The number displayed is the current Zone value. • If a new Zone value is desired, briefly press the “Left” button to increment the displayed value, (Range 1–15) until you find your desired Zone number. • No button activity for 4–5 seconds ends the Zone entry mode. The display will return to normal operation and the new Zone number will be set. I nf or mat i onPr ov i dedby : 3 54 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Calibration If “CAL” is not displayed, press and hold the “Left” button for 10–15 seconds, or until “CAL” appears in the display, then release the button. The compass is now in calibration mode. Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. The mirror can be calibrated in one of two ways • Drive the vehicle in circles at less then 5 mph (8 km/h) until “CAL” no longer appears in the display. • Drive the vehicle under normal operating conditions. Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. I nf or mat i onPr ov i dedby : WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror. UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Remote-Control Mirrors — If Equipped Use the mirror select switch, located on the drivers door trim panel, to adjust the view obtained in the outside mirrors. Press the rocker knob to the L or R for Left or Right mirror selection. Use the center off position to guard against accidentally moving a mirror position. 55 SEATS Front Seat Adjustment The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Select a mirror and press one of the four arrows for the direction you want the mirror to move. Manual Front Seat Adjuster Power Mirror Switches Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched after the adjustment bar is released. I nf or mat i onPr ov i dedby : 3 56 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Manual Recline Handle I nf or mat i onPr ov i dedby : UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical. Push in on the release button to lower the head restraint. 57 Folding Rear Seat To provide additional storage area, the center of each rear seatback can be folded forward. Pull on the loops shown in the picture to fold down either or both seatbacks. 3 Folding Rear Seat Adjustable Head Restraint I nf or mat i onPr ov i dedby : 58 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seatbelts • Be sure that everyone in your vehicle is in a seat and using a seatbelt properly. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the driver’s side of the instrument panel. Hood Release Lever I nf or mat i onPr ov i dedby : UNDERSTANDING THE FEATURES OF YOUR VEHICLE 59 Then lift the safety catch located under the front edge of the hood, near the center and raise the hood. 3 Hood Prop Rod WARNING! Hood Safety Catch Use the hood prop rod to secure the hood in the open position as shown. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. I nf or mat i onPr ov i dedby : If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. 60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Front Map/Reading Lights — If Equipped These lights, located under the rearview mirror, can be turned on by means of switches located at the base of the rearview mirror. Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 8 minutes if a door is left open or the dimmer control is left in the Dome light position. Turn the ignition switch ON to restore the interior light operation. Dimmer Control With the park lights or headlights on, rotating the dimmer control for the interior lights on the MultiFunction Control Lever upward will increase the brightness of the instrument panel lights. Front Map/Reading Lights NOTE: The map lights will remain on when the ignition switch is in the Run or Accessory positions. I nf or mat i onPr ov i dedby : UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position. 61 lights, the passing lights, and fog lights. The lever is located on the left side of the steering column. Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Daytime Brightness Feature Certain instrument panel components can be illuminated at full brightness during the daytime. These are the Odometer and Radio. This can be helpful when driving with your headlights on during the daytime such as in a parade or a funeral procession. To activate this feature, rotate the dimmer ring on the left stalk one detent lower than the dome light. Multi-Function Control Lever The Multi-Function Control Lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior Multi-Function Control Lever To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down. I nf or mat i onPr ov i dedby : 3 62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (Canada Only) The front fog lights will come on as Daytime Running Lights whenever the ignition is on, the headlights are off, and the parking brake is off. The headlight switch must be used for normal night time driving. Lights-on Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound when the driver’s door is opened. Leaving the headlights on for an extended period of time will discharge the battery resulting in reduced battery life and possible inability to start the vehicle. Fog Lights — If Equipped The front fog light switch is on the Multi-Function Control Lever. To activate the front fog lights, turn on the headlights and pull out the end of the control lever. NOTE: The fog lights will only operate with the headlights on low beam. Selecting high beam headlights or park lights will turn off the fog lights. Turn Signals Move the Multi-Function Control Lever up or down to detent and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down. If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective. Headlight Dimmer Switch Pull the Multi-Function Control Lever towards you to switch the headlights to HIGH beam. Pull the control lever a second time to switch the headlights to LOW beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the Multi-Function Control Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. I nf or mat i onPr ov i dedby : UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. Move the control lever up to select the desired wiper speed. 63 two wipe cycles after the lever is released, and then resume the intermittent interval previously selected. If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF. 3 CAUTION! • In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. Windshield Wiper/Washer Control Windshield Washers To use the washer, pull the control lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate in low speed for Mist Function Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. I nf or mat i onPr ov i dedby : 64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Move the lever to the first detent (DEL) position, then select the delay interval by turning the end of the lever. Rotate the knob upward (clockwise) to decrease the delay time and downward (counterclockwise) to increase the delay time. The delay can be regulated from a maximum of approximately 18 seconds between cycles, to a cycle every second. TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towards you to lock the column firmly in place. Lo Speed Wipers Move the wiper stalk upward to the 2nd detent to obtain a low speed wiper function. Hi Speed Wipers Move the wiper stalk upward to the 3rd position to obtain the fastest wiper speed. Tilt Steering Column Control I nf or mat i onPr ov i dedby : UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The speed control lever is located on the right side of the steering wheel. 3 Speed Control Lever To Activate: Push the ON/OFF button. The CRUISE indicator in the instrument cluster will illuminate. To turn the system OFF, push the ON/OFF button a second time. The CRUISE indicator will turn off. The system should be turned OFF when not in use. I nf or mat i onPr ov i dedby : 66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set At A Desired Speed: When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever. To Deactivate: A soft tap on the brake pedal, pulling the speed control lever towards you “CANCEL”, or normal brake or clutch pressure while slowing the vehicle will deactivate speed control without erasing the set speed memory. Pressing the ON/OFF button or turning off the ignition switch erases the set speed memory. To Resume Speed: To resume a previously set speed, push the “ACC/RES” lever up and release. Resume can be used at any speed above 32 km/h (20 mph). To Vary The Speed Setting: When the speed control is ON, speed can be increased by pushing up and holding “ACC/RES”. Release the lever when the desired speed is reached, and the new speed will be set. Tapping “ACC/RES” once will result in a 2 mph (3 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 6 mph (10 km/h), etc. To decrease speed while speed control is ON, push down and hold “COAST/SET”. Release the lever when the desired speed is reached, and the new speed will be set. Tapping the “COAST/SET” button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases. I nf or mat i onPr ov i dedby : UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Transaxle: Depressing the clutch pedal will disengage the speed control. A slight increase in engine RPM before the speed control disengages is normal. Vehicles equipped with manual transaxles may need to be shifted into a lower gear to climb hills without speed loss. WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery. 67 To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Speed Control On Hills NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. Vehicles equipped with four speed automatic transaxles may experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control. I nf or mat i onPr ov i dedby : 3 68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The sunroof control is located on the headliner between the sun visors. Once the sunroof panel is in the full vent position, you may momentarily move the switch rearward (less than one second) to initiate the express open mode. During this operation, any movement of the switch will stop the sunroof and it will remain in a partial open position. NOTE: When closing the sunroof, make sure the close button is held in the close position until the motor stops. This ensures the sunroof is fully closed and latched. To close the sunroof, hold the switch in the forward position. Again, any release of the switch will stop the movement and the sunroof will remain in a partial open condition until the switch is pushed forward again. CAUTION! Power Sunroof Switch A single control “tilts” the sunroof to the vent position and also slides the sunroof rearward to the full open position. Move the switch rearward to move the sunroof panel to the full vent position. The sunroof can be stopped at any position between closed and full vent open. I nf or mat i onPr ov i dedby : The sunroof should not be operated above 70 mph. Opening or closing the sunroof above 70 mph may jam the sunroof mechanism. UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof. Never allow fingers or other body parts, or any object to project through the sunroof opening. Injury may result. 69 Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if so equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. I nf or mat i onPr ov i dedby : 3 70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES The Standard console with armrest has two front cup holders and a front storage tray. There are two additional cupholders; one is molded in the center of the console to hold large cups, and the other is on the underside of the console lid to serve passengers in the rear seat. The underside console lid also has an integral tissue pack holder. The covered storage area has CD and cassette holders. Ash Receiver and Cigar Lighter When the Smoker’s Package is ordered from your authorized dealer, an ash receiver tray and a cigar lighter element are furnished. The lighter element can be inserted in the auxiliary power outlet. The ash receiver fits snugly in a cupholder position. To clean the ash receiver, lift it from the cupholder. Ash Receiver Tray Front Console I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instrument Panel Features . . . . . . . . . . . . . . . .74 ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . .83 m Standard Instrument Cluster . . . . . . . . . . . . . . .75 m Sales Code RBB—AM/FM Stereo Radio With Cassette Tape Player And CD Changer Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 m Optional Instrument Cluster . . . . . . . . . . . . . . .76 m Instrument Cluster Descriptions . . . . . . . . . . . .77 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . .83 m Electronic Digital Clock . . . . . . . . . . . . . . . . . .82 ▫ Mode Button . . . . . . . . . . . . . . . . . . . . . . . . .85 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . .82 ▫ Scan Button (Radio Mode) . . . . . . . . . . . . . . . .85 m Radio General Information . . . . . . . . . . . . . . . .82 ▫ Cassette Player Features . . . . . . . . . . . . . . . . .86 ▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . .82 ▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . .82 ▫ CD Changer Control Capability — If Equipped . .87 ▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . .83 m Sales Code RBK—AM/ FM Stereo Radio With CD Player And CD Changer Controls . . . . . . . .88 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . .83 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . .88 I nf or mat i onPr ov i dedby : 4 72 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ CD Player Operation . . . . . . . . . . . . . . . . . . . .90 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . .96 ▫ CD Changer Control Capability — If Equipped . .92 m Cassette Tape And Player Maintenance . . . . . . .97 m Satellite Radio — If Equipped . . . . . . . . . . . . . .93 m 6 Disc CD Changer — If Equipped . . . . . . . . . .98 ▫ System Activation . . . . . . . . . . . . . . . . . . . . . .94 ▫ Loading The CD Changer . . . . . . . . . . . . . . . .98 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . .94 ▫ Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . .99 ▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . .99 ▫ Selecting Satellite Mode In RBB, RAH And RBK Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 ▫ FF/Tune/RW . . . . . . . . . . . . . . . . . . . . . . . . .99 ▫ Mode Button . . . . . . . . . . . . . . . . . . . . . . . . .99 ▫ Selecting Satellite Mode In RBP, RBU, RAZ, RB1 And RBQ Radios . . . . . . . . . . . . . . . . . . . . . .95 ▫ Program Button 1 . . . . . . . . . . . . . . . . . . . . . .99 ▫ Selecting a Channel . . . . . . . . . . . . . . . . . . . . .95 ▫ Program Button 4 (Random Play) . . . . . . . . . . .99 ▫ Storing And Selecting Pre-Set Channels . . . . . . .95 ▫ Program Button 5 . . . . . . . . . . . . . . . . . . . . . .99 ▫ Using The PTY (Program Type) Button (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . .96 ▫ Time Button . . . . . . . . . . . . . . . . . . . . . . . . . 100 ▫ Changing Modes . . . . . . . . . . . . . . . . . . . . . . 100 ▫ PTY Button 9Scan9 . . . . . . . . . . . . . . . . . . . . . .96 ▫ Removing Discs From The CD Changer . . . . . 100 ▫ PTY Button 9Seek9 . . . . . . . . . . . . . . . . . . . . . .96 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . .96 ▫ CD Changer Operation With The Changer Off . . 100 m Compact Disc Maintenance . . . . . . . . . . . . . . . 100 I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL 73 m Radio Operation And Cellular Phones . . . . . . . 101 ▫ Outside Air Intake . . . . . . . . . . . . . . . . . . . . 103 m Climate Controls . . . . . . . . . . . . . . . . . . . . . . 101 ▫ Air Conditioning — If Equipped . . . . . . . . . . 103 ▫ Heater Only . . . . . . . . . . . . . . . . . . . . . . . . . 101 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 108 ▫ Side Window Demisters . . . . . . . . . . . . . . . . . 103 m Electric Rear Window Defroster . . . . . . . . . . . 110 4 I nf or mat i onPr ov i dedby : 74 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL 75 STANDARD INSTRUMENT CLUSTER 4 I nf or mat i onPr ov i dedby : 76 UNDERSTANDING YOUR INSTRUMENT PANEL OPTIONAL INSTRUMENT CLUSTER I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Front Fog Light Indicator — If Equipped This light shows when the front fog lights are ON. (See page 62 for more information.) 2. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light comes on, it may indicate that the parking brake is applied, or there is a low brake fluid level. On vehicles equipped with Anti-lock brakes (ABS), it may also indicate an ABS malfunction that could lead to reduced braking performance. WARNING! Driving a vehicle with the brake light on is dangerous. A significant decrease in braking performance or vehicle stability during braking may occur. It will take you longer to stop the vehicle or will make your vehicle harder to control. You could have an accident. Have the vehicle checked immediately. 77 The operation of the Brake Warning light can be checked by turning the ignition key from the OFF to the ON position. The light should illuminate for three seconds, or until the engine is started, whichever comes first. The light should then go out unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected and serviced as soon as possible. The light will also come on when the parking brake is applied with the ignition in the ON position. NOTE: This light shows only that the parking brake is on. It does not show the degree of brake application. If the parking brake is off and the light remains on, have the brake system inspected as soon as possible. 3. Anti-Lock Warning Light (ABS) — If Equipped This light monitors the Anti-Lock Brake System (ABS) described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for as long as four seconds. I nf or mat i onPr ov i dedby : 4 78 UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light remains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required, however, the conventional brake system will continue to operate normally provided that the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefit of Anti-Lock Brakes. The warning light should be checked frequently to assure that it is operating properly. Turn the ignition key to a point midway between ON and START. The light should come on. If the light does not come on, have the system checked by an authorized dealer. 4. Speedometer Indicates vehicle speed. 5. Turn Signal Indicators The arrows will flash in unison with the exterior turn signal, when using the turn signal lever. (See page 62 for more information.) 6. High Beam Indicator This light shows that the headlights are on high beam. Pull the turn signal lever toward the steering wheel to switch the headlights from high or low beam. 7. Tachometer — If Equipped The white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 8. Oil Pressure Light Shows low engine oil pressure. The light will come on and remain on when the ignition key is turned from the OFF to the ON position, and the light will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer. If the light comes on and remains on while driving, stop the vehicle and shut off the engine. DO NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS CORRECTED. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL 79 The light does not show the quantity of oil in the engine. This can be determined using the procedure shown in Section 7. (See page 169 for more information.) come on during starting, stays on, or comes on while driving, have the system checked by an authorized dealer. (See page 39 for more information.) 9. Seat Belt Reminder Light When the ignition key is first turned on, this light will come on for about six seconds. A chime will sound if you have not pulled the shoulder belt out of the retractor. This is a reminder to “buckle up”. If you do not buckle up, the light will remain on. 12. Theft Alarm Light — If Equipped This light will flash rapidly for several seconds when the alarm system is arming. The light will begin to flash slowly indicating that the system is armed. (See page 22 for more information.) 10. Charging System Light This light shows the status of the electrical charging system. The light should come on briefly when the ignition is first turned on and remain on briefly as a bulb check. If the light stays on or comes on while driving, it means that there is a problem with the charging system. Obtain SERVICE IMMEDIATELY. 11. Airbag Light The light comes on and remains on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the light does not 13. Fuel Door Reminder This symbol is a reminder that the Fuel Filler Door is located on the passenger’s side of the vehicle. 14. Fuel Gauge When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 15. Low Fuel Light — If Equipped NOTE: The Low Fuel Light and Chime feature only functions on vehicles equipped with a tachometer. When the fuel level drops to about 1/8 tank, the fuel symbol will light and a single chime will sound. The light will remain on until fuel is I nf or mat i onPr ov i dedby : 4 80 UNDERSTANDING YOUR INSTRUMENT PANEL added. If the fuel level drops to about 1/2 gallon, the fuel symbol will begin to flash and the chime will sound several times. converter damage. The vehicle should be serviced as soon as possible if this occurs. (See page 166 for more information.) 16. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transmission control systems. The light will illuminate briefly when the key is in the ON/RUN position before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly. 17. Odometer/Trip Odometer Reset Knob Press this knob to switch between the odometer and trip odometer. While the trip odometer is being displayed, press and hold this knob for a few seconds to reset the trip odometer to zero miles/kilometers. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing. 18. Odometer/Trip Odometer Shows the total distance the vehicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. Therefore, if the odometer reading changes during repair or replacement, be sure to keep a record of the reading before and after the service so the correct mileage can be determined. If the Malfunction Indicator Light flashes when the engine is running, serious conditions may exist that could lead to immediate loss of power or severe catalytic I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL 19. Door Ajar Indicator This vacuum fluorescent display indicator illuminates when a door is not completely closed. If the door is open for more than 8 minutes and the ignition key is in the OFF position, the indicator will turn off. 20. Trip Indicator This light will illuminate when the Trip Odometer is in use. 21. Cruise Light — If Equipped This indicator shows that the Speed Control System is ON. (See page 65 for more information.) NOTE: The word “SET” will not illuminate when the Speed Control System is on. 22. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading between the light blue and red areas of the gauge shows that the engine cooling system is operating properly. The 81 gauge pointer may show a higher than normal temperature when driving in hot weather, up mountain grades, in heavy stop and go traffic, or when towing a trailer. If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull off the road at a safe area. With the vehicle in Park, idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the H (red) mark, turn the ignition off immediately and call for service. There are steps that you can take to slow down an impending overheat condition. If your air conditioning is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to Floor and the Fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. I nf or mat i onPr ov i dedby : 4 82 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK RADIO GENERAL INFORMATION The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position. Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning. To help you understand and save you concern about these “apparent” malfunctions, you must understand a point or two about the transmission and reception of radio signals. When the ignition switch is in the OFF position, or when the radio frequency is being displayed, time keeping is accurately maintained. Clock Setting Procedure 1. Turn the ignition switch to the ON or ACC position. Using the tip of a ballpoint pen or similar object, press either the hour (H) or minute (M) buttons on the radio. The display will show TIME. 2. Press the H button to set hours or the M button to set minutes. The time setting will increase each time you press a button. Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. 83 SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs. 4 FM Reception Because FM transmission is based on frequency variations, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio. RBB Radio Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. I nf or mat i onPr ov i dedby : 84 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played. For your convenience, the volume can be turned down, but not up, when the audio system is off and the ignition is ON. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button will bypass stations without stopping until you release it. Tune Press the TUNE control up or down to increase or decrease the frequency. If the button is pushed and held, the radio will continue to tune until the button is released. The frequency will be displayed and continuously updated while the button is pushed. To Set The Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. The symbol SET 1 will now show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed. Audio The audio button controls the BASS, TREBLE, BALANCE, and FADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones. Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers. Press the AUDIO button a fourth time and FADE will be displayed. Press the SEEK + or SEEK – to adjust the sound level between the front and rear speakers. 85 Press the AUDIO button again or wait 5 seconds to exit setting tone, balance, and fade. AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received in the FM mode. Mode Button Press the MODE button to select between the cassette tape player, CD changer, or the Satellite Radio (if equipped). When the Satellite Radio (if equipped) is selected “SAT” will appear in your radio display. A CD or tape may remain in the player while in the Satellite or radio mode. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time. I nf or mat i onPr ov i dedby : 4 86 UNDERSTANDING YOUR INSTRUMENT PANEL Cassette Player Features With ignition OFF and the sound system OFF, you can eject the tape cassette by pushing the EJECT button. You can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on. Each time a cassette is inserted the tape player will begin playing on the side of the cassette that is facing up in the player. Music Search Pressing the SEEK button while playing a tape will start the Music Search mode. Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection, or return to the beginning of the previous selection if the tape is within the first 5 seconds of the current selection. The SEEK symbol appears on the display when Music Search is in operation. Music Search shuts off automatically when a selection has been located. Selective Music Search Press the SEEK button up or down to move the track number to skip forward or backward 1 to 7 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward And Rewind Buttons Pressing the TUNE button up or down momentarily activates Fast Forward or Rewind and makes the directional arrows appear on the display. To stop Fast Forward or Rewind, press the TUNE button again. Time Button Press the time button to toggle between station frequency and time of day. SCAN Button (Cassette Mode) Pressing this button while playing a cassette tape will change the side of the tape being played. NR (Noise Reduction) Pushing the Number 2 Pre-set button when a tape is playing deactivates the Dolby Noise Reduction System*. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL 87 When Dolby is ON, the NR symbol appears on the display. Each time a tape is inserted the Dolby will turn ON. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. * “Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The following instructions are for the radio controls that operate this CD changer. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played. The audio output can be heard when fast forward and fast reverse are activated. Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. I nf or mat i onPr ov i dedby : 4 88 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. • Water condensation on optics SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display. A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected. An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration • Disc inserted upside down • Damaged disc RBK Radio Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL 89 NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up or the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed. Tune Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continuously updated while the button is pressed. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 Audio The audio button controls the BASS, TREBLE, BALANCE, and FADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. I nf or mat i onPr ov i dedby : 4 90 UNDERSTANDING YOUR INSTRUMENT PANEL Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones. Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers. Press the AUDIO button a fourth time and FADE will be displayed. Press the SEEK + or SEEK – to adjust the sound level between the front and rear speakers. Press the AUDIO button again or wait 5 seconds to exit setting tone, balance, and fade. AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation. NOTE: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Time Press the TIME button to change the display between radio frequency and time. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL 91 beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Inserting The Compact Disc CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. EJT — Eject Press the EJT button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode. You may either insert or eject a disc with the radio OFF. If you do not remove the disc within 15 seconds, it will be reloaded. The unit will continue in radio mode. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. The disc can be ejected with the radio and ignition OFF (except on convertibles). If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the tracks on the selected disc in random order to provide an interesting change of pace. I nf or mat i onPr ov i dedby : 4 92 UNDERSTANDING YOUR INSTRUMENT PANEL Press the SEEK button to move to the next randomly selected track. Press the RND (button 4) button a second time to stop Random Play. Mode Press the MODE button repeatedly to select between the CD player, the optional remote CD changer and the Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “SAT” will appear in your radio display. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. A CD or tape may remain in the player while in the Satellite mode. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. Time Press the TIME button to change the display from elapsed CD playing time to time of day. Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The following instructions are for the radio controls that operate this CD changer. The audio output can be heard when fast forward and fast reverse are activated. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display. A CD HOT symbol indicates the player is too hot. 93 CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected. An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration • Disc inserted upside down • Damaged disc • Water condensation on optics SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio. This service offers up to 100 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios. I nf or mat i onPr ov i dedby : 4 94 UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following information available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Credit card information. 3. Your Vehicle Identification Number. Electronic Serial Number/Sirius Identification Number (ENS/SID) The Electronic Serial Number/Sirius Identification Number is needed to activate your Sirius Satellite Radio system. To access the ESN/SID, refer to the following steps: ESN/SID Access With RBB, RAH and RBK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the Tape Eject or CD Eject (depending on the radio type) and Time buttons simultaneously for 3 seconds. The first four digits of the twelve-digit ESN/SID number will be displayed. Press the SEEK UP button to display the next four digits. Continue to press the SEEK UP button until all twelve ESN/SID digits have been displayed. The SEEK DOWN will page down until the first four digits are displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. ESN/SID Access With RBP, RBU, RAZ, RB1 and RBQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID numbers will be displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in RBB, RAH and RBK Radios Press the MODE button repeatedly until 9S A9 appears in the display. A CD or tape may remain in the radio while in the Satellite radio mode. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL Selecting Satellite Mode in RBP, RBU, RAZ, RB1 and RBQ Radios Press the MODE button repeatedly until the word 9SIRIUS9 appears in the display. These radios will also display the following: • After 3 seconds, the current channel name and channel number will be displayed for 5 seconds. • The current program type and channel number will then be displayed for 5 seconds. • The current channel number will then be displayed until an action occurs. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting a Channel Press and release the SEEK or TUNE buttons to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released. 95 Press and release the SCAN button (if equipped) to automatically change channels every 7 seconds. The radio will pause on each channel for 7 seconds before moving on to the next channel. The word 9SCAN9 will appear in the display between each channel change. Press the SCAN button a second time to stop the search. NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-539-7474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations. Follow the memory pre-set procedures that apply to your radio. I nf or mat i onPr ov i dedby : 4 96 UNDERSTANDING YOUR INSTRUMENT PANEL Using the PTY (Program Type) Button (if equipped) Follow the PTY button instructions that apply to your radio. PTY Button (SCAN( When the desired program type is obtained, press the 9SCAN9 button within five seconds. The radio will play 7 seconds of the selected channel before moving to the next channel of the selected program type. Press the 9SCAN9 button a second time to stop the search. NOTE: Pressing the 9SEEK9 or 9SCAN9 button while performing a music type scan will change the channel by one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. PTY Button (SEEK( When the desired program is obtained, press the 9SEEK9 button within five seconds. The channel will change to the next channel that matches the program type selected. Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons. • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly diminished. 2. Keep the cassette tape in its case to protect from slackness and dust when it is not in use. 3. Keep the cassette tape away from direct sunlight, heat and magnetic fields such as the radio speakers. 4. Before inserting a tape, make sure that the label is adhering flatly to the cassette. 97 Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played. The result of deposits on the capstan shaft may cause the tape to wrap around and become lodged in the tape transport. The other adverse condition is low or “muddy” sound from one or both channels, as if the treble tone control were turned all the way down. To prevent this, you should periodically clean the head with a commercially available WET cleaning cassette. As preventive maintenance, clean the head about every 30 hours of use. If you wait until the head becomes very dirty (noticeably poor sound), it may not be possible to remove all deposits with a simple WET cleaning cassette. 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. I nf or mat i onPr ov i dedby : 4 98 UNDERSTANDING YOUR INSTRUMENT PANEL 6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3⁄4 inch (12 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in front of the changer. Each disc has a numbered button with an amber light above it which, when illuminated, indicates that a disc is loaded in that particular chamber. Loading the CD Changer When inserting the first CD into the changer if the radio is on, wait until the single slot is illuminated on both sides and simply insert the first disc. To insert additional CDs into the changer, the instructions follow: 1. Select and press any numbered button without an illuminated light above it. 2. Insert the CD while the light above the chosen button is flashing and the two lights on either side of the slot are illuminated. 3. Upon insertion, the CD will begin to play, and both the button light and the lights in the corner of the loading slot will illuminate. 6 Disc CD Changer 4. Repeat the process for loading any additional CDs. The CD player will stop while additional CDs are loaded. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL Playing Discs The radio will show the CD number, the CD track number, and the Track Time Elapsed while the radio is in the CD mode. If more than one CD is loaded in the changer, the changer will automatically play the next disc after playing the last track of the current disc. Seek Button Press the top of this button on the radio once to play the next track. Press the bottom of the button once to return to the beginning of the current track. Press the bottom of the button twice to play the previous track. FF/TUNE/RW Press the FF (fast forward) button and the CD player will fast forward through the tracks until the button is released. Press the RW (rewind) button and the CD player will reverse through the tracks until the button is released. 99 Program Button 1 Press this button to play the next available disc. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the current compact disc in random order to provide an interesting change of pace. The CD changer stays in the random play mode when changing to the next disc. NOTE: The changer will not random play between discs. Press the top of the Seek button once to move to the next randomly selected track. Press the bottom of the Seek button to go back to the beginning of the track. Press button 4 a second time to stop random play. Program Button 5 Press this button to play the previous disc. Mode Button Press this button to toggle between radio and cd modes. I nf or mat i onPr ov i dedby : 4 100 UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press this button to switch between time of day and CD track time. To eject additional CDs from the changer, first select the numbered button where the CD is located and then press the EJT button. Changing Modes While in the radio mode, if a cassette is loaded, press the Mode button to switch to the tape mode. If a CD is loaded, press the Mode button to select the CD mode. If neither a tape nor CD is loaded, the radio will ignore the command. CD Changer Operation with the Changer Off The CD changer is able to load and eject discs with the ignition power off. However, while the ignition is off, one of the six numbered buttons must be pressed first. • Inserting either a tape or CD automatically starts that mode of play. • Pressing the AM/FM button while in the tape or CD mode will select the radio mode. • If in the CD mode and the last CD is ejected, the radio will tune to the last station selected. Removing Discs from the CD Changer If there is a single CD in the changer, press the EJT button and the CD will eject. If the CD is not removed within 15 seconds, it will automatically reload into the CD changer. COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL 6. Do not expose the disc to direct sunlight. CLIMATE CONTROLS 7. Do not store the disc where temperatures may become too high. Heater Only The controls are as follows: NOTE: If you experience difficulty in playing a particular disc, it may be damaged, oversized, or have theft protection encoding. Try a known good disc before considering disc player service. Fan Control RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio. If your radio performance does not satisfactorily “clear” by the repositioning of the antenna, it is recommended that the radio volume be turned down or off during cellular phone operation. 101 Use this control to regulate the amount of air forced through the system in any mode you select. Turn the control clockwise to increase fan speed. Turn the control to the full counterclockwise position to turn the fan off. NOTE: There is always a small amount of air entering the vehicle even when the fan is turned off. If this becomes objectionable during cold weather, place the mode control on FLOOR to direct the air flow away from passengers. I nf or mat i onPr ov i dedby : 4 102 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) The mode control allows you to choose from several patterns of air distribution. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The center point between modes gives an even blend of both modes. The closer the control is to a particular mode, the more air distribution you receive from that mode. Panel Air is directed through the adjustable outlets in the instrument panel. Bi-Level Air is directed through the panel and floor outlets. Floor Air is directed through the floor and side window demist outlets with a small amount through the defrost outlet. Mix Air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Defrost Air is directed through the windshield and side window demister outlets. Use this setting with maximum fan and heat settings for the best windshield and side window clearing. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. Turn the control clockwise to increase the temperature of the air entering the vehicle. Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors. 103 The blower air will heat faster in cold weather if you use only a low blower speed for the first few minutes of vehicle operation. During engine warm-up in cold weather, use the Defrost mode to direct any cold air away from the occupants. Air Conditioning — If Equipped The Air Conditioning System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle. The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere. Outside Air Intake When operating the system during the winter months, make sure the air intake, directly in front of the windshield, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains. I nf or mat i onPr ov i dedby : CAUTION! If your vehicle was not built with air conditioning, The manufacturer does not recommend that you install any non-factory A/C system. The design of add-on air conditioning kits may be inadequate. This may cause damage to your engine or other components. 4 104 UNDERSTANDING YOUR INSTRUMENT PANEL The controls are as follows: Fan and Air Conditioning Control Use this control to regulate the amount of air forced through the system in any mode you select. The fan speeds to the left of the OFF position are for Air Conditioning. Choosing one of these speeds turns on the air conditioning compressor. The fan speed increases as you move the control counterclockwise from the OFF position. NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds. Mode Control (Air Direction) The mode control allows you to choose from several patterns of air distribution. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The center point between modes gives an even blend of both modes. The closer the control is to a particular mode, the more air distribution you receive from that mode. Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow. Fan speeds to the right of OFF are for heater or ventilation operation. The fan speed increases as you move the control clockwise from the OFF position. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Air is directed through the panel and floor outlets. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. NOTE: If you choose either the Mix or Defrost modes while the Circulation control is in the Recirculation Mode, the system will automatically switch to the Outside Air mode and the knob will move to that position. Floor Air is directed through the floor outlets and side window demist outlets with a small amount through the defrost outlet. 105 Mix Air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Defrost Air is directed through the windshield and side window demist outlets. Use this mode with maximum fan and temperature settings for best windshield and side window defrosting. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes even if the fan switch is not in the A/C position. This dehumidifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary. I nf or mat i onPr ov i dedby : 4 106 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Circulation Control Use this control to regulate the temperature of the air inside the passenger compartment. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures. NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser located in front of the radiator, for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may reduce air flow to the condenser, reducing air conditioning performance. Use this control to choose between outside air intake or recirculation of the air inside the vehicle. Only use the recirculate mode to temporarily block out any outside odors, smoke, or dust and to cool the interior rapidly upon initial start up in very hot or humid weather. This control only operates in the Outside Air and Recirculate modes; there is no in between position. Do not place the control between these positions. NOTE: Continuous use of the recirculate mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL In cold weather, the use of the Recirculate position will cause windows to fog on the inside because of moisture build up inside the vehicle. For maximum defogging, select the Outside Air position. 107 NOTE: If you choose either the Mix or Defrost modes and the Circulation control is in the Recirculate Mode, the system will automatically switch to the Outside Air position. If the mode control is in the range between Mix and Defrost and you choose the Recirculate mode, the mode control knob will automatically move to the Mix position. I nf or mat i onPr ov i dedby : 4 108 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips I nf or mat i onPr ov i dedby : UNDERSTANDING YOUR INSTRUMENT PANEL 109 Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur. Outside Air Intake When operating the system during the winter months, make sure the air intake, directly in front of the windshield, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains. Interior fogging on the windshield can be quickly removed by using the defrost position. The blower air will heat faster in cold weather if you use only a low blower speed for the first few minutes of vehicle operation. If the fogging problem persists, clean the inside window surfaces. The cause of undue fogging may be dirt collecting on the inside surface of the glass NOTE: In cold weather, the use of the recirculate position will cause windows to fog on the inside because of moisture build up inside the vehicle. For maximum defogging, use the Outside Air position. Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors. Summer Operation Air conditioned vehicles must be protected with a highquality antifreeze coolant to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50% concentration is recommended. I nf or mat i onPr ov i dedby : 4 110 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRIC REAR WINDOW DEFROSTER A push-button at the center of the instrument panel, below the radio, turns the defroster and the heated mirrors (if equipped) ON or OFF. An amber light shows that the defroster is on. NOTE: The defroster turns off automatically after 10 minutes of operation. Each following activation of the defroster will last for five minutes. CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off after soaking with warm water. Rear Defroster Switch I nf or mat i onPr ov i dedby : STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . 114 ▫ Automatic Transaxle Ignition Interlock System . . 116 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 114 ▫ Four Speed Automatic Transaxle . . . . . . . . . . 117 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 114 ▫ Reset Mode . . . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 114 ▫ Gear Ranges For Four Speed Automatic Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ Starting In Cold Weather (Below 32°F Of 0°C) . . . . . . . . . . . . . . . . . . . 115 m Manual Transaxle — If Equipped . . . . . . . . . . 119 ▫ Recommended Shift Speeds . . . . . . . . . . . . . . 120 ▫ Extremely Cold Weather (Below -20°F Or -29°C) . . . . . . . . . . . . . . . . . 115 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 115 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . . 116 m Automatic Transaxle — If Equipped . . . . . . . . 116 ▫ Downshifting . . . . . . . . . . . . . . . . . . . . . . . . 120 m Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . 121 m Brake System . . . . . . . . . . . . . . . . . . . . . . . . . 122 ▫ Brake/Transmission Interlock System . . . . . . . 116 I nf or mat i onPr ov i dedby : ▫ Anti-Lock Brake System (ABS) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 123 5 112 STARTING AND OPERATING m Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 124 m Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 m Tire Safety Information . . . . . . . . . . . . . . . . . . 124 m Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 124 m Tire Rotation Recommendations . . . . . . . . . . . 141 ▫ Tire Identification Number (TIN) . . . . . . . . . . 127 m Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 141 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 128 ▫ Spark Knock . . . . . . . . . . . . . . . . . . . . . . . . . 142 m Tires—General Information . . . . . . . . . . . . . . . 132 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . . 142 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 132 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . . 142 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . . 133 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . . 143 ▫ Radial-Ply Tires . . . . . . . . . . . . . . . . . . . . . . 135 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 143 ▫ Compact Spare Tire — If Equipped . . . . . . . . . 135 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 143 ▫ Limited Use Spare — If Equipped . . . . . . . . . 136 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 144 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . . 137 m Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 144 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . . 137 ▫ Fuel Tank Filler Cap . . . . . . . . . . . . . . . . . . . 144 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 138 m Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . 146 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 139 m Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 146 I nf or mat i onPr ov i dedby : STARTING AND OPERATING ▫ Trailer Towing Information (Maximum Trailer Weight Ratings) . . . . . . . . . 147 ▫ Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 113 ▫ Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 m Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . 148 5 I nf or mat i onPr ov i dedby : 114 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Automatic Transaxle The gear selector must be in the NEUTRAL or PARK position before you can start the engine. CAUTION! NOTE: You must press the brake pedal before shifting out of Park. Long periods of engine idling, especially at high engine speeds can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. Manual Transaxle Place the gear selector in NEUTRAL, press the clutch pedal to the floor, and fully apply the parking brake before starting the engine. NOTE: The engine will not start unless the clutch pedal is pressed to the floor. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. Normal Starting Normal Starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal. Simply turn the key to the START position and release when the engine starts. If the engine has not started within 5 seconds, slightly depress the accelerator pedal while continuing to crank. If the engine fails to start within 15 seconds, turn the key to the OFF position, wait 10 to 15 seconds, then repeat the normal starting procedure. I nf or mat i onPr ov i dedby : STARTING AND OPERATING Starting in Cold Weather (Below 32°F of 0°C) Slightly depress and hold the accelerator before starting the engine. Turn the key to the START position. When the engine starts, release the key, then the accelerator pedal. If the engine fails to start within 15 seconds, turn the key OFF wait 10 to 15 seconds, then repeat the normal starting procedure. WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. See section 6 of this manual for jump starting instructions. 115 Extremely Cold Weather (below -20°F or -29°C) To insure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your dealer) is recommended. If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL STARTING” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there. Crank the engine for no more than 15 seconds. This should clear any excess fuel in case the engine is flooded. Leave the ignition key in the ON position, release the accelerator pedal and repeat the “NORMAL STARTING” procedure. I nf or mat i onPr ov i dedby : WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. 5 116 STARTING AND OPERATING CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After Starting The idle speed will automatically decrease as the engine warms up. AUTOMATIC TRANSAXLE — IF EQUIPPED CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal. NOTE: You MUST press and hold the brake pedal down while shifting out of Park. Brake/Transmission Interlock System This system prevents you from moving the gear shift out of Park and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON positions. Always depress the brake pedal first, before moving the gear selector out of PARK. Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK and the shift knob push button is out. It also prevents shifting out of PARK unless the key is in the ON or RUN positions. I nf or mat i onPr ov i dedby : STARTING AND OPERATING NOTE: If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few shift cycles. Reset Mode The transaxle is monitored electronically for abnormal conditions. If a condition is detected that could cause damage, the transaxle shifts automatically into second gear. The transaxle remains in second gear despite the forward gear selected. Park (P), Reverse (R), and Neutral (N) will continue to operate. This second gear limp-in feature allows the vehicle to be driven to a dealer for service without damaging the transaxle. In the event that the problem has been momentary, the transaxle can be reset to regain all forward gears. 117 Stop the vehicle and shift into Park (P). Turn the Key to OFF then restart the engine. Shift into D and resume driving. NOTE: Even if the transaxle can be reset, it is recommended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. If the transaxle cannot be reset, dealer service is required. Gear Ranges For Four Speed Automatic Transaxle DO NOT race the engine when shifting from PARK or NEUTRAL positions into another gear range. “P” Park Supplements the parking brake by locking the transmission. The engine can be started in this range. Never use P (Park) while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, and then place the selector in P (Park) position. I nf or mat i onPr ov i dedby : 5 118 STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the transmission shift lever is locked in the P (Park) position, securing the vehicle against unwanted movement. Furthermore, you should never leave children unattended inside a vehicle. The following indicators should be used to ensure that you have engaged the transmission shift lever into the P (Park) position: • When shifting into P (Park), depress the button on the shift lever and firmly move the lever all the way forward until it stops. • Look at the shift indicator window on the console to ensure it is in the P (Park) position. • When engaged in P (Park), you will not be able to move the shifter rearward without depressing the shift lever button. CAUTION! Before moving the shift lever out of P (Park), you must turn the ignition from LOCK to ON so the steering wheel and shift lever are released. Otherwise, damage to the steering column or shifter could result. “R” Reverse Shift into this range only after the vehicle has come to a complete stop. “N” Neutral Engine may be started in this range. “D” Overdrive This range should be used for most city and highway driving. It provides smoothest up shifts and down shifts and best fuel economy. I nf or mat i onPr ov i dedby : STARTING AND OPERATING When frequent transaxle shifting occurs while using the Overdrive range, such as when operating the vehicle under heavy loading conditions (in hilly terrain, traveling into strong head winds, or while towing trailers), use the “3” range. 119 MANUAL TRANSAXLE — IF EQUIPPED NOTE: The parking brake should be engaged and the gear selector placed in REVERSE before leaving the vehicle, especially on an incline. NOTE: Clutch must be depressed for engine to start. “3” Drive This range eliminates shifts into Overdrive. The transaxle will operate normally in first and second while in this range. Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelerator pedal. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance, fuel economy, and extend transaxle life by reducing excessive shifting and heat build up. Use each gear in numerical order - do not skip a gear. Be sure the transaxle is in FIRST gear, (not THIRD), when starting from a standing position. Damage to the clutch can result from starting in THIRD. Use the “3” range when descending steep grades to prevent brake system distress. For most city driving you will find it easier to use only the lower gears. For steady highway driving with light accelerations, 5th gear is recommended. “1” Low This range should be used for maximum engine braking when descending steep grades. In this range, up shifts will occur only to prevent engine over speed while down shifts from 2nd to first will occur as early as possible. Never drive with your foot resting on the clutch pedal, or try to hold the vehicle on a hill with the clutch pedal partially engaged. This will cause abnormal wear on the clutch. Never shift into REVERSE until the vehicle has come to a complete stop. I nf or mat i onPr ov i dedby : 5 120 STARTING AND OPERATING NOTE: During cold weather, until the transaxle lubricant has warmed, you may have difficulty shifting. This is normal and not harmful to the transaxle. For improved performance, your manual transaxle may be upshifted up to the maximum speeds listed in table 3 (within legal speed limits). Recommended Shift Speeds To use your manual transaxle for optimal fuel economy, it should be upshifted as listed in tables 1 and 2. TABLE 3-MANUAL TRANSAXLE RECOMMENDED SHIFT SPEEDS IN MPH (KM/H) ENGINE MAXIMUM PERFORMANCESHIFT SPEEDS SIZE 1 to 2 2 to 3 3 to 4 4 to 5 30 50 80 110 2.0L (48) (80) (129) (177) TABLE 1-MANUAL TRANSAXLE RECOMMENDED SHIFT SPEEDS IN MPH (KM/H) ENGINE NORMAL ACCELERATION SHIFT SPEEDS SIZE 1 to 2 2 to 3 3 to 4 4 to 5 14 23 29 45 2.0L (23) (37) (47) (72) TABLE 2-MANUAL TRANSAXLE RECOMMENDED SHIFT SPEEDS IN MPH (KM/H) ENGINE CRUISE SHIFT SPEEDS SIZE 1 to 2 2 to 3 3 to 4 4 to 5 12 18 25 32 2.0L (19) (29) (40) (51) If you exceed these speeds, you may notice the engine cut in and out. This is caused by an electronic limiter in the engine computer. The engine will run normally when you reduce engine speed. Downshifting Proper downshifting may improve fuel economy and prolong engine life. I nf or mat i onPr ov i dedby : STARTING AND OPERATING CAUTION! If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transaxle, or clutch. 121 release the parking brake, apply the brake pedal and pull up on the parking brake lever. Push the release button and lower the lever fully. To maintain a safe speed and prolong brake life, shift down to 2nd or 1st when descending a steep grade. 5 When turning a corner, or driving up a steep grade, shift down early so that the engine will not be overburdened. PARKING BRAKE When the parking brake is applied with the ignition on, the Brake Light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on. It does not show the degree of brake application. Before leaving the vehicle, make sure that the parking brake is set. To set the parking brake, pull up firmly on the lever. Also place the gear selector in the Park position (automatic transaxle) or Reverse (manual transaxle). To Parking Brake Lever When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. I nf or mat i onPr ov i dedby : 122 STARTING AND OPERATING You should always apply the parking brake before leaving the vehicle. WARNING! • Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and an accident. BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating. WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. If either of the two hydraulic systems lose normal capability, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the I nf or mat i onPr ov i dedby : STARTING AND OPERATING malfunction is caused by an internal leak, as the brake fluid in the master cylinder drops, the brake warning indicator will light. Anti-Lock Brake System (ABS) — If Equipped The ABS gives increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock up. All vehicle wheels and tires must be the same size and tires must be properly inflated to produce accurate signals for the computer. However, the system will compensate when the compact spare is in use. During stops where ABS is activated, a vibration of the brake pedal may be felt and associated system noises may be heard. NOTE: Pumping of the brake pedal will diminish the effectiveness of Anti-lock brakes and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. I nf or mat i onPr ov i dedby : 123 WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. • The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. 5 124 STARTING AND OPERATING POWER STEERING The power assisted steering system of your vehicle provides mechanical steering capability in the event power assist is lost. If for some reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort. TIRE SAFETY INFORMATION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H • LT(Light Truck)-Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric tires is the same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preceding the size designation. Example: LT235/85R16. • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation. Example: T145/80D18 103M. • High Flotation tire sizing is based on U.S. design standards and begins with the tire diameter molded into the sidewall. Example: 31x10.5 R15 LT. I nf or mat i onPr ov i dedby : STARTING AND OPERATING 125 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.5 = Section Width in Inches (in) R = Construction Code —9R9 means Radial Construction. —9D9 means Diagonal or Bias Construction. 15 = Rim Diameter in Inches (in) I nf or mat i onPr ov i dedby : 5 126 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits). Load Identification: (....blank....( = Absence of any text on sidewall of the tire indicates a Standard Load (SL) Tire Extra Load (XL) = Extra Load (or Reinforced) Tire Light Load = Light Load Tire C,D,E = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load — Maximum Load indicates the maximum load this tire is designed to carry. Maximum Pressure — Maximum Pressure indicates the maximum permissible cold tire inflation pressure for this tire. I nf or mat i onPr ov i dedby : STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. 127 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire. EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards, and is approved for highway use. MA = Code representing the tire manufacturing location.(2 digits) L9 = Code representing the tire size.(2 digits) ABCD = Code used by tire manufacturer.(1 to 4 digits) 03 = Number representing the week in which the tire was manufactured.(2 digits) —03 means the 3rd week. 01 = Number representing the year in which the tire was manufactured.(2 digits) —01 means the year 2001. —Prior to July 2000, tire manufacturers were only required to have 1 number to represent the year in which the tire was manufactured. Example: 031 could represent the 3rd week of 1981 or 1991. I nf or mat i onPr ov i dedby : 5 128 STARTING AND OPERATING Tire and Loading Information Placard Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for passenger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the shutface of the driver’s door, the “B” pillar, the Certification Label or in the Tire Inflation Pressures brochure in the glove compartment. Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Tire Placard Location I nf or mat i onPr ov i dedby : STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual. NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWR’s) for the front and rear axles must not be exceeded. For further information on GAWR’s, vehicle loading and trailer towing, see the Vehicle Loading section of this manual. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. 129 Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (since 5 x 150 = 750, and 1400 – 750 = 650 lb.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. I nf or mat i onPr ov i dedby : 5 130 STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle. NOTE: For the following example the combined weight of occupants and cargo should never exceed 865 lbs. (392 Kg). I nf or mat i onPr ov i dedby : STARTING AND OPERATING 131 5 I nf or mat i onPr ov i dedby : 132 STARTING AND OPERATING 1. Safety— WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: I nf or mat i onPr ov i dedby : WARNING! Improperly inflated tires are dangerous and can cause accidents. • Under inflation increases tire flexing and can result in tire failure. • Over inflation reduces a tire’s ability to cushion shock. Objects on the road and chuck holes can cause damage that results in tire failure. • Unequal tire pressures can cause steering problems. You could lose control of your vehicle. • Over inflated or under inflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control. • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. Always drive with each tire inflated to the recommended cold tire inflation pressure. STARTING AND OPERATING 133 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride. Tire Inflation Pressures The proper cold tire inflation pressure for passenger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the “B” pillar, the Certification Label or in the Tire Inflation Pressures brochure in the glove compartment. Some vehicles may have Supplemental Tire Pressure Information for vehicle loads that are less than the maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 5 Tire Placard Location The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. I nf or mat i onPr ov i dedby : 134 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1mile (1 km) after a 3 hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire side wall. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change. Keep this in mind when checking tire pressure inside a garage especially in the winter. Example: If garage temperature = 68° F (20° C) and the outside temperature = 32° F (0° C) then the cold tire inflation pressure should be increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12° F (7° C) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high speed vehicle operation. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. I nf or mat i onPr ov i dedby : STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). 135 Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs. Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. Radial-Ply Tires WARNING! WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. I nf or mat i onPr ov i dedby : Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary-use spare tires have limited tread life. When two or more tread wear indicators appear in adjacent grooves, the temporary use spare tire needs to be replaced. Be sure to follow the warnings which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control. 5 136 STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on vehicle at the first opportunity. Do not install more than one compact spare tire/wheel on the vehicle at any given time. WARNING! CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result. Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited use spare I nf or mat i onPr ov i dedby : The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle. Failure to do so could result in loss of vehicle control. STARTING AND OPERATING 137 Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). See the paragraph on Freeing A Stuck Vehicle in Section 6 of this manual. WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. 5 These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point. I nf or mat i onPr ov i dedby : 138 STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed (see the paragraph on tread wear indicators). Refer to the Tire and Loading Information placard for the size designation of your tire. The service description and load identification will be found on the original equipment tire. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. We recommend that you contact your original equipment or an authorized tire dealer with any questions you may have on tire specifications or capability. I nf or mat i onPr ov i dedby : WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death. Use only the tire and wheel sizes with load ratings approved for your vehicle. • Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have an accident. • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear. • Vehicle pull to right or left. 139 Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your dealer for proper diagnosis. Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. Tire Chains If driving conditions require tire chains for your vehicle, chains that meet SAE class “S” requirements can be used, but they must be installed on tire sizes P175/70R14, 185/65R14, P185/65R14, 185/60R15, or P185/60R15 tires. Contact your local dealership or tire dealer for these tire sizes. I nf or mat i onPr ov i dedby : 5 140 STARTING AND OPERATING CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate chain breakage. Remove the damaged parts of the chain before further use. • Install chains on the front wheels as tightly as possible and then retighten after driving about 1⁄2 mile (0.8 km). • Do not exceed 45 mph (70 km/h). • Drive cautiously and avoid severe turns and large bumps, especially with a loaded vehicle. • Do not drive for prolonged period on dry pavement. • Observe the tire chain manufacturer’s instructions on the method of installation, operating speed, and conditions for use. Always use the lower suggested operating speed of the chain manufacturer if different than the speed recommended by the manufacture. Snow Tires Some areas of the country require the use of snow tires during winter. Standard tires are of the all season type and satisfy this requirement as indicated by the M+S designation on the tire side wall. If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of 4, failure to do so may adversely affect the safety and handling of your vehicle. Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). I nf or mat i onPr ov i dedby : STARTING AND OPERATING 141 Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels, and contribute to a smooth, quiet ride. Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected before rotating. The suggested rotation method is the “forward-cross” shown in the diagram. FUEL REQUIREMENTS Your engine is designed to meet all emission regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an octane rating of 87. The use of premium gasoline is not recommended. The use of premium gasoline will provide no benefit over high quality regular gasolines, and in some circumstances may result in poorer performance. I nf or mat i onPr ov i dedby : 5 142 STARTING AND OPERATING Spark Knock Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, try another brand of “regular” gasoline before considering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning fuel referred to as Reformulated Gasoline. Reformulated gasolines contain oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability for the engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with materials called oxygenates such as 10% ethanol, MTBE and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasolines containing Methanol. Gasoline containing methanol may damage critical fuel system components. Problems that result from using methanol/gasoline blends are not the responsibility of The manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol. I nf or mat i onPr ov i dedby : STARTING AND OPERATING MMT in Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasolines blended with MMT provide no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles. The manufacturer recommends that gasolines free of MMT be used in your vehicle. The MMT content of gasoline may not be indicated on the gasoline pump, therefore you should ask your gasoline retailer whether or not his/her gasoline contains MMT. It is even more important to look for gasolines without MMT in Canada because MMT can be used at higher levels than allowed in the United States. MMT is prohibited in both Federal and California reformulated gasolines. Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal 143 conditions and would result in unnecessary cost. Therefore you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: 5 • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance. • The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol. I nf or mat i onPr ov i dedby : 144 STARTING AND OPERATING Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. Carbon Monoxide Warnings WARNING! • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. ADDING FUEL Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period. If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. NOTE: The fuel tank filler tube has a restricting door about 2 inches (50 mm) down from the opening. If fuel is poured from a portable container, the container should have a flexible nozzle long enough to force open the restricting door. Fuel Tank Filler Cap The gas cap is behind the fuel filler door, on the passenger’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap has been designed for use with this vehicle. I nf or mat i onPr ov i dedby : STARTING AND OPERATING CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. 145 NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that the cap is properly tightened. If the gas cap is not tightened properly, the Malfunction Indicator light will come on. Be sure the gas cap is tightened every time the vehicle is fueled. WARNING! CAUTION! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. A poorly fitting gas cap may cause the Malfunction Indicator Lamp to turn on. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. • Turn off engine. • Rotate the gas cap to the left to remove. CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. • To replace the cap, insert it into the filler neck and tighten to the right until at least one click is heard. I nf or mat i onPr ov i dedby : 5 146 STARTING AND OPERATING WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Rear Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . . 3 Luggage . . . . . . . . . . . . . . . . . . . . . . . 115 lbs. (52 kg) Rated Vehicle Capacity. . . . . . . . . . . . 865 lbs. (392 kg) TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible. Perform maintenance services as prescribed in the maintenance schedules manual. When your vehicle is used for trailer towing, never exceed the gross axle weight rating (GAWR) by the addition of: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. • Remember that everything put in or on the trailer adds to the load on your vehicle. I nf or mat i onPr ov i dedby : STARTING AND OPERATING Trailer Towing Information (Maximum Trailer Weight Ratings) (Trailer Towing Guide( NOTE: For trailer towing information (maximum trailer weight ratings) refer to the following website address: http:// www.dodge.com/towing. In Canada, refer to the following website address: http:// www.dodge.ca. Warranty To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing. However the following conditions must be met: • The maximum trailer load for vehicles with the Standard 2.0L Engine and manual tranaxles is 1,500 lbs (680 kg). • The maximum trailer load for vehicles with the Standard 2.0L Engine and automatic transaxles is 1,000 lbs (454 kg). 147 • If using a manual transaxle vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. • The maximum frontal area of the trailer cannot exceed 20 square feet (1.86 square meters). • The trailer tongue load must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to the Tire– Safety Information Section in this manual. • The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range must be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transaxle life by reducing excessive shifting and heat build up. I nf or mat i onPr ov i dedby : 5 148 STARTING AND OPERATING WARNING! Connecting trailer brakes to your vehicle’s hydraulic brake lines can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • Do not attempt to tow a trailer while using a compact spare tire. • Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are recommended for motoring safety. • The automatic transaxle fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation. See Schedule “B” in section 8 of this manual for transaxle fluid change intervals. NOTE: Check the automatic transaxle fluid level before towing. NOTE: For vehicles equipped with Autostick. By using the Autostick modes, and selecting a specific gear range, frequent shifting can be avoided. The highest gear range should be selected that allows for adequate performance. For example, choose “4” if the desired speed can be maintained. Choose “3” or “2” if needed to maintain the desired speed. NOTE: Extended driving at high RPM should be avoided to prevent excess heat generation. A reduction in vehicle speed may be required to avoid extended driving at high RPM. Return to a higher gear range or vehicle speed when road conditions and RPM level allows. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Recreational towing on vehicle’s equipped with automatic transaxle’s is not recommended. NOTE: If the vehicle requires towing make sure all four wheels are off the ground. If your vehicle is equipped with a manual transaxle, it may be towed with all four wheels on the ground at any legal highway speed, for any distance, if the transaxle is in neutral. I nf or mat i onPr ov i dedby : WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . 150 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 m If Your Engine Overheats . . . . . . . . . . . . . . . . 150 m Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 159 m Jacking And Tire Changing . . . . . . . . . . . . . . . 152 m Towing A Disabled Vehicle . . . . . . . . . . . . . . . 160 ▫ Preparations For Jacking . . . . . . . . . . . . . . . . 152 ▫ With Ignition Key . . . . . . . . . . . . . . . . . . . . . 160 ▫ Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 152 ▫ Without The Ignition Key . . . . . . . . . . . . . . . 161 m Jump-Starting Procedures If Battery Is Low . . . 155 ▫ Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 m Driving On Slippery Surfaces . . . . . . . . . . . . . 158 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 158 I nf or mat i onPr ov i dedby : 6 150 WHAT TO DO IN EMERGENCIES If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. HAZARD WARNING FLASHER NOTE: With extended use, the flasher may wear down your battery. IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down. • In city traffic — While stopped, put transaxle in neutral, but do not increase engine idle speed. Hazard Flasher Switch The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn Hazard Warning Flashers off. Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to floor, and I nf or mat i onPr ov i dedby : WHAT TO DO IN EMERGENCIES the fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service. I nf or mat i onPr ov i dedby : 151 WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 6 152 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, and set the parking brake. Place the gear selector in PARK (automatic transaxle) or REVERSE (manual transaxle). • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. • Passengers should not remain in the vehicle while the vehicle is being jacked. Instructions The spare wheel, scissors jack, and lug wrench are stowed under the spare tire cover in the rear cargo area. Do not attempt to raise this vehicle using a bumper jack. I nf or mat i onPr ov i dedby : WHAT TO DO IN EMERGENCIES 1. Remove the spare wheel, scissors jack and lug wrench from stowage. 153 CAUTION! Do not attempt to raise the vehicle by jacking on the crossmember below the radiator or on the front suspension crossmember. 3. Jack saddle support must be positioned in between locating darts at the front of the vehicle and behind locating dart at the rear. Turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. 2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. I nf or mat i onPr ov i dedby : 6 154 WHAT TO DO IN EMERGENCIES Do not raise the vehicle until you are sure the jack is securely engaged. 5. Remove the wheel nuts and pull the wheel and wheel covers where applicable off the hub. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts. To avoid the risk of forcing the vehicle off the jack, do not tighten the nuts fully until the vehicle has been lowered. WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. 4. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire clears the surface. Miminum tire lift provides maximum vehicle stability. NOTE: The wheel cover is held on the wheel by the wheel nuts. When reinstalling original wheel, properly align the wheel cover to the valve stem, place the wheel cover onto the wheel, then install the wheel nuts. 6. Lower the vehicle by turning the jack screw to the left. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 7. Finish tightening the nuts. Push down on the wrench while tightening the wheel nuts. Alternate nuts until each nut has been tightened twice. Correct wheel nut torque is I nf or mat i onPr ov i dedby : WHAT TO DO IN EMERGENCIES 100 ft. lbs. (135 N·m). If you are not sure about the tightness, have them checked with a torque wrench by your dealer or at a service station. 155 JUMP-STARTING PROCEDURES IF BATTERY IS LOW 8. Remove the wheel blocks and lower the jack until it is free. Stow the lug wrench, replaced tire, and jack. Secure all parts using the means provided. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 9. Adjust the tire pressure as soon as possible. NOTE: The spare tire well is designed to hold the compact spare tire or a deflated (flat) tire. A fully inflated tire will not fit in the spare tire well. I nf or mat i onPr ov i dedby : WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully. 6 156 WHAT TO DO IN EMERGENCIES 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch. Set parking brake, place automatic transaxle in PARK (manual transaxle in NEUTRAL) and turn ignition to OFF for both vehicles. 3. Turn off the heater, radio and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end to the positive terminal of the discharged battery. I nf or mat i onPr ov i dedby : WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. WHAT TO DO IN EMERGENCIES 157 WARNING! WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water. A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes. Do not use a booster battery or any other booster source with an output that exceeds 12 volts. Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode. The battery temperature must be brought up above freezing point before attempting to jump start. 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. If the vehicle is equipped with sentry key immobilizer, turn the ignition switch to the ON/RUN position for 3 seconds prior to moving the ignition switch to the crank position and starting the vehicle. 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. I nf or mat i onPr ov i dedby : 6 158 WHAT TO DO IN EMERGENCIES 8. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels, particularly with high output engines. 3. Damage to charging system of booster vehicle or of immobilized vehicle. I nf or mat i onPr ov i dedby : WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.). WHAT TO DO IN EMERGENCIES Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when roads are slushy. 159 FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and First gear. Usually the least accelerator pedal pressure to maintain the rocking motion without spinning the wheels is most effective. 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain enough distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. I nf or mat i onPr ov i dedby : WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. 6 160 WHAT TO DO IN EMERGENCIES CAUTION! Racing the engine or spinning the wheels too fast may lead to transaxle overheating and failure. It can also damage the tires. Do not spin the wheels above 35 mph (55km/h). Manual Transaxle Your vehicle may be towed if the gearshift lever is in NEUTRAL. If the transaxle is not operative, the vehicle must be towed with the front wheels off the ground. All Transaxles CAUTION! TOWING A DISABLED VEHICLE If the vehicle being towed requires steering, the ignition switch must be in the OFF position, not in the LOCK or ACCESSORY positions. With Ignition Key Four Speed Automatic Transaxle Your vehicle may be towed under the following conditions: The steering column must be unlocked and the gear selector must be in NEUTRAL, the distance to be towed must not exceed 100 miles (160 km), and the towing speed must not exceed 44 mph (72 km/h). If the transaxle is not operative, or if the vehicle is to be towed more than 100 miles (160 km), the vehicle must be towed with the front wheels off the ground to avoid damage to the transaxle. If it is necessary to use the accessories while being towed (wipers, defrosters, etc.), the key must be in the ON position, not the ACCESSORY position. Make certain the transaxle remains in NEUTRAL. I nf or mat i onPr ov i dedby : WHAT TO DO IN EMERGENCIES Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position. A dolly should be used under the front wheels if the rear wheels are raised. Proper towing equipment is necessary to prevent damage to the vehicle. 161 Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) If your vehicle is equipped with a manual transaxle, it may be towed at any legal highway speed, for any distance, if the transaxle is in neutral. If the ignition key is not available, vehicles with automatic transaxles can not be flat towed at any time. 6 I nf or mat i onPr ov i dedby : I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE CONTENTS m 2.0L Engine Compartment . . . . . . . . . . . . . . . 165 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . . 176 m Onboard Diagnostic System — OBD II . . . . . . 166 ▫ Air Conditioner . . . . . . . . . . . . . . . . . . . . . . 177 m Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 ▫ Power Steering Fluid Check . . . . . . . . . . . . . . 178 m Replacement Parts . . . . . . . . . . . . . . . . . . . . . 168 m Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . 168 m Maintenance Procedures . . . . . . . . . . . . . . . . . 169 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 169 ▫ Ignition Wiring System . . . . . . . . . . . . . . . . . 175 ▫ Crankcase Emission Control System . . . . . . . . 175 ▫ Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 175 ▫ Air Cleaner Element (Filter) . . . . . . . . . . . . . . 175 I nf or mat i onPr ov i dedby : ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 178 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 178 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 179 ▫ Windshield Wiper Blade Replacement . . . . . . . 179 ▫ Windshield Washer Aiming . . . . . . . . . . . . . . 180 ▫ Windshield Washer Reservoir . . . . . . . . . . . . . 180 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 180 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . . 181 7 164 MAINTAINING YOUR VEHICLE ▫ Hoses And Vacuum/Vapor Harnesses . . . . . . . 185 m Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 199 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . . 186 ▫ Headlight Bulb Replacement . . . . . . . . . . . . . 199 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 188 ▫ Front Park/Turn Signal Lights . . . . . . . . . . . . 201 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 190 ▫ Front Sidemarker Light . . . . . . . . . . . . . . . . . 201 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 ▫ Tail/Stop, Rear Turn Signals And Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . 201 m Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 ▫ Center High Mounted Stop Light . . . . . . . . . . 201 ▫ Underhood Fuses (Power Distribution Center) . . . . . . . . . . . . . . 195 m Fluids And Capacities . . . . . . . . . . . . . . . . . . . 202 ▫ Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . 197 m Recommended Fluids, Lubricants And Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . 203 m Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . 198 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 m Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . 198 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE 165 2.0L ENGINE COMPARTMENT 7 I nf or mat i onPr ov i dedby : 166 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations. If any of these systems require service, the OBD II system will turn on the “Malfunction Indicator Light.” It will also store diagnostic codes and other information to assist your service technician in making repairs. Although your vehicle will usually be drivable and not need towing, see your dealer for service as soon as possible. I nf or mat i onPr ov i dedby : CAUTION! • Prolonged driving with the “Malfunction Indicator Light” on could cause further damage to the emission control system. It could also affect fuel economy and driveability. The vehicle must be serviced before any emissions tests can be performed. • If the “Malfunction Indicator Light” is flashing while the engine is running, severe catalytic converter damage and power loss will soon occur. Immediate service is required. MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing. 167 2. Turn the ignition to the ON position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: Normally, the OBD system will be ready. The OBD system may not be ready if your vehicle was recently serviced, if you recently had a dead battery, or a battery replacement. If the OBD system should be determined not ready for the I/M test, your vehicle may fail the test. Your vehicle has a simple ignition key actuated test which you can use prior to going to the test station. To check if your vehicle’s OBD system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. I nf or mat i onPr ov i dedby : a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. 7 168 MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready. Regardless of whether your vehicle’s OBD system is ready or not ready, if the MIL symbol is illuminated during normal vehicle operation, you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. REPLACEMENT PARTS Use of genuine Mopar parts for normal/scheduled maintenance and repairs is highly recommended to insure the designed performance. Damage or failures caused by the use of non-Mopar parts for maintenance and repairs will not be covered by the manufacturer warranty. DEALER SERVICE Your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE 169 Engine Oil WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. I nf or mat i onPr ov i dedby : 7 Engine Oil Dipstick Location 170 MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines. CAUTION! Overfilling or underfilling will cause aeration or loss of oil pressure. This could damage your engine. Engine Oil Dipstick Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to decide if any apply to you. • Day and night temperatures are below 32°F (0°C) • Stop and Go driving • Extensive engine idling I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE 171 • Driving in dusty conditions • Short trips of less than 10 miles (16.2 km) • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C) • Trailer towing • Taxi, Police, or delivery service (commercial service) • Off-road or desert operation • If equipped for and operating with E-85 (ethanol) fuel NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the 9Maintenance Schedules9 section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule 9A9 of the 9Maintenance Schedules9 section of this manual. Oil Filler Cap Location Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API certified and meet the requirements of DaimlerChrysler Material Standard MS-6395. NOTE: Under no circumstances should oil change intervals exceed 6000 miles (10 000 km) or 6 months whichever comes first. I nf or mat i onPr ov i dedby : 7 172 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils. Engine Oil Viscosity (SAE Grade) SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Refer to your engine oil filler cap for the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, see the Engine Compartment illustration in this section. Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used. Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that are American Petroleum Institute (API) Certified and have the recommended SAE viscosity grade. Follow the maintenance schedule that describes your driving type. Materials Added To Engine Oils The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil Care should be taken in disposing of used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment. Contact your dealer, service station, or governmental agency for advice on how and where used oil can be safely discarded in your area. I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection All of this manufacturers engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar Engine Oil Filters are high quality oil filters and are recommended. Drive Belts — Check Condition and Tension At the mileage shown in the maintenance schedules, check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure. Inspect the drive belts for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt failure. If adjustment is required, adjust the belts according to the specifications and procedures shown in the Service Manual. 173 Special tools are required to properly measure tension and to restore belt tension to factory specifications. Also, check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New plugs should be installed at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug. Check the specifications section for the proper type of spark plug for use in your vehicle. Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. I nf or mat i onPr ov i dedby : 7 174 MAINTAINING YOUR VEHICLE CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, including a tune up to manufacturers specifications, should be obtained immediately. To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. • Do not idle the engine with any spark plug wires disconnected for prolonged period. Engine Timing Belt Replace the engine timing belt at the intervals described in the appropriate maintenance schedule. I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE Ignition Wiring System The ignition cables should be kept clean and properly connected. Terminals should be fully seated. Cracked, damaged, or faulty cables should be replaced. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits. If a valve is not working properly, replace it with a new valve. DO NOT ATTEMPT TO CLEAN THE OLD PCV VALVE! 175 Air Cleaner Element (Filter) Under normal driving conditions, replace the filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the intervals shown on Schedule “B”. Check ventilation hose for indication of damage or plugging deposits. Replace if necessary. Fuel Filter A plugged fuel filter can cause hard starting or limit the speed at which a vehicle can be driven. Should an excessive amount of dirt accumulate in the fuel tank, frequent filter replacement may be necessary. I nf or mat i onPr ov i dedby : WARNING! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failure to do so can result in serious personal injury. 7 176 MAINTAINING YOUR VEHICLE Maintenance-Free Battery The top of the MAINTENANCE-FREE battery is permanently sealed. You will never have to add water, nor is periodic maintenance required. CAUTION! When servicing the battery, always reinstall the battery thermowrap. The thermowrap provides battery heat protection and will extend overall battery life. Failure to reinstall the thermowrap can result in evaporative loss of the battery fluid. I nf or mat i onPr ov i dedby : WARNING! Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Don’t use a booster battery or any other booster source with an output greater than 12 volts. Don’t allow cable clamps to touch each other. MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening. If a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to battery. Do not use a “fast charger” to provide starting voltage as battery damage can result. Air Conditioner Check the air conditioning system at the start of the warm weather season. 177 a gentle water spray from behind the radiator and through the condenser as required. Fabric front fascia protectors may reduce air flow to the condenser, reducing air conditioning performance. WARNING! The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced repairman. 7 Refrigerant Recovery And Recycling The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere, the manufacturer recommends that air conditioning service be done by facilities using refrigerant recycling and recovery equipment that meets SAE standard J1991. NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser for an accumulation of dirt or insects. Clean with I nf or mat i onPr ov i dedby : 178 MAINTAINING YOUR VEHICLE Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through a certified DaimlerChrysler Dealership. WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid types. Front Suspension Ball Joints There are two front suspension lower ball joints that are permanently lubricated. Inspect these ball joints whenever under-vehicle service is done. Damaged seals should be replaced to prevent leakage or grease contamination. Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, trunk and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopart Lock Cylinder Lubricant directly into the lock cylinder. I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner, or use the washer solvent. This will remove accumulations of salt or road film and help reduce streaking and smearing. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Make sure that they are not frozen to the glass before turning them on to avoid damaging the blade. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield Wiper Blade Replacement 179 3. Push the release tab shown in the picture and slide the wiper blade assembly down along the arm. Gently place the wiper arm on the windshield. 7 4. Install the new blade assembly onto the wiper arm tip until it locks in place. 1. Lift the wiper arm away from the glass. 2. Rotate the blade 45 degrees to gain access to the release tab. I nf or mat i onPr ov i dedby : 180 MAINTAINING YOUR VEHICLE Windshield Washer Aiming To change the aim of the windshield washers, place a safety pin into the nozzle opening and move the nozzle slightly. Continue making slight adjustments until you obtain the desired pattern. Windshield Washer Reservoir The washer fluid reservoir is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; I nf or mat i onPr ov i dedby : WARNING! Exhaust gases can injure or kill. They contain carbon monoxide which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. Follow the above precautions to keep your exhaust system as safe as possible. MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. 181 Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of coolant from the radiator drain cock. If the cap is sealing properly, the engine coolant (antifreeze) will begin to drain from the coolant recovery bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT. I nf or mat i onPr ov i dedby : 7 182 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution. Selection Of Coolant Use only the manufacturers recommended coolant, refer to Recommended Fluids, Lubricants and Genuine Parts for correct coolant type. I nf or mat i onPr ov i dedby : CAUTION! Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. This vehicle has not been designed for use with Propylene Glycol based coolants. Use of Propylene Glycol based coolants is not recommended. MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) coolant. When adding coolant, a minimum solution of 50% recommended Mopar Antifreeze/ Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology), or equivalent, in water should be used. Use higher concentrations (not to exceed 70%) if temperatures below 234°F (237°C ) are anticipated. 183 Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Use only high purity water such as distilled or deionized water when mixing the water/engine coolant solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. I nf or mat i onPr ov i dedby : 7 184 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result. Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling, and warm to normal operating temperature, the level of the coolant in the bottle should be between the ranges indicated on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for coolant freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot coolant to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain coolant concentration at 50% HOAT engine coolant (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components. 185 • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also. • Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, checking, tear, cuts, abrasions, and excessive swelling indicate deterioration of the rubber. Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear. I nf or mat i onPr ov i dedby : 7 186 MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of degradation that could cause failure. Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Maintenance Section. WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage. Hard and brittle rubber, cracking, checking, tears, cuts, abrasions, and excessive swelling suggest deterioration of the rubber. Particular attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold. Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. Insure nylon tubing in these areas has not melted or collapsed. NOTE: Often, fluids such as oil, power steering fluid, and brake fluid are used during assembly plant operations to ease the assembly of hoses to couplings. Therefore, oil wetness at the hose-coupling area is not necessarily an indication of leakage. Actual dripping of hot fluid when systems are under pressure (during vehicle operation) should be noted before hose is replaced based on leakage. I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE 187 NOTE: Inspection of brake hoses should be done whenever the brake system is serviced and every engine oil change. WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp is on. Brake Fluid Master Cylinder Use only manufacturers recommended brake fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. I nf or mat i onPr ov i dedby : WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident. 7 188 MAINTAINING YOUR VEHICLE WARNING! CAUTION! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Using a transmission fluid other than the manufacturers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes. Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter. Do not allow petroleum based fluid to contaminate the brake fluid as seal damage will result! Automatic Transaxle All front wheel drive vehicles have a transaxle and differential assembly contained within a single housing. Selection of Lubricant It is important that the proper lubricant is used in the transaxle to assure optimum transaxle performance. Use only manufacturers recommended transmission fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. Fluid Level Check The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and of the fluid. Procedure for Checking Fluid Level Check the fluid level while the transmission is at normal operating temperature. This occurs after at least 15 miles (25 km) of driving. At normal operating temperature, which is approximately 180°F ( 82°C), the fluid cannot be held comfortably between the fingertips. I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE To check the fluid level properly, the following procedure must be used: 1. The vehicle must be on level ground. 189 reference holes when the transmission reaches 180°F (82°C). Remember it is best to check the level at the normal operating temperature. 2. The engine should be running at curb idle speed for a minimum of 60 seconds. 3. Fully apply parking brake. 4. Place the gear selector momentarily in each gear position ending with the lever in P (PARK). 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be in the crosshatch area at normal operating temperatures. If the fluid is low, add as required into the dipstick tube. Do not overfill. 7 If the fluid level shows low, add sufficient transmission fluid to bring to the proper level. NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be between the two COLD (lower) holes on the dipstick with the fluid at approximately 80°F (27°C) (room temperature). If the fluid level is correctly established at room temperature, it should be between the HOT (upper) I nf or mat i onPr ov i dedby : 190 MAINTAINING YOUR VEHICLE CAUTION! If the transaxle is disassembled for any reason, the fluid and filter should be changed. Do not overfill. Dirt and water in the transaxle can cause serious damage. To prevent dirt and water from entering the transaxle after checking or replenishing fluid, make certain that the dipstick cap is seated properly. Special Additives The manufacturer recommends against the addition of any fluid additives to the transaxle. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. The use of transmission sealers should be avoided as they may adversely affect seals. Fluid and Filter Changes Automatic transmission fluid and filter should be changed as follows: Maintenance schedule “A” — No change necessary. Maintenance schedule “B” – Every 60,000 miles (96 000 km) change fluid and filter under the following conditions: • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for maintenance schedules. Manual Transaxle Lubricant Selection Use only manufacturers recommended transmission fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. Fluid Level Check Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more that 3/16” (4.76 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the following conditions exist: • The lubricant has become contaminated with water. If contaminated with water, the fluid should be changed immediately. • If severe usage has occurred, refer to Maintenance Schedule “B” in Section 8 of this manual. 191 hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: Appearance Care and Protection from Corrosion • Road salt, dirt and moisture accumulation. Protection of Body and Paint from Corrosion Vehicle body car requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in you vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near sea coast localities. • Atmospheric fallout/industrial pollutants. I nf or mat i onPr ov i dedby : 7 192 MAINTAINING YOUR VEHICLE Washing Special Care • Wash your vehicle regularly. Always wash your vehicle in the shade using a mild car wash soap, and rinse the panels completely with clear water. • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • If insects, tar or other similar deposits have accumulated on your vehicle, wash it as soon as possible. • It is important that the drain holes in the lower edges of the doors, rocker panels and rear deck lid be kept clear and open. • Use Mopar auto polish to remove road film and stains and to polish your vehicle. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Many wheel cleaners contain acids that may harm the wheel surface. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • Use Mopar touch up paint on scratches or chips as soon as possible. Your dealer has touch up paint to match the color of your vehicle. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, deicer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. Wheel And Wheel Trim Care All wheels and wheel trim, especially Aluminum and Chrome plated, should be cleaned regularly, using mild soap and water to maintain their luster and to prevent corrosion. Wash them with the same soap solution as the body of your vehicle. Rinse wheels thoroughly. 193 • Any abrasive cleaning pad (such as steel wool) or abrasive brush • Any cleaner that contains an acid which can react with and discolor the chrome surface. CAUTION! Many wheel cleaners contain acids that may harm the wheel surface. • Oven cleaner When cleaning extremely dirty wheels, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels. Only Mopar Wheel Cleaners are recommended. Any of the “DO NOT USE” items listed below can damage wheels and wheel trim. • A car wash that uses carbide-tipped wheel cleaning brushes or acidic solutions. DO NOT USE: Use Mopar Vinyl Cleaner to clean vinyl upholstery. • Any abrasive cleaner Mopar Vinyl Cleaner is specifically recommended for vinyl trim. Interior Care Use Mopar Fabric Cleaner to clean fabric upholstery and carpeting. I nf or mat i onPr ov i dedby : 7 194 MAINTAINING YOUR VEHICLE Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. Instrument Panel Cover The instrument panel cover has a low glare surface which minimizes reflections in the windshield. Do not use protectants or other products which may cause undesirable reflections. Use soap and warm water to restore the low glare surface. I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in the vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content of abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 195 FUSES Underhood Fuses (Power Distribution Center) A Power Distribution Center is located in the engine compartment; next to the battery. A label identifying the components and circuits is located on the underside of the cover. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. 7 If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the vehicle to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly. I nf or mat i onPr ov i dedby : Underhood Fuses (Power Distribution Center) 196 MAINTAINING YOUR VEHICLE MAXI FUSE 1 2 3 4 5 6 7 8 9 10 Amp/Color — — 40 Amp/ Green 40 Amp/ Green 30 Amp/Pink 30 Amp/Pink Spare 40 Amp/ Green 30 Amp/Pink 40 Amp/ Green Items Fused MINI FUSE — — Headlamps 11 12 13 Ignition Run 14 ABS Solenoid Radiator Fan 15 16 17 ABS Pump Starter Electric Back Light (EBL) 18 19 20 21 22 23 I nf or mat i onPr ov i dedby : Amp/Color Spare Spare 20 Amp/ Yellow 20 Amp/ Yellow 15 Amp/Blue 15 Amp/Blue 20 Amp/ Yellow 10 Amp/Red Spare 20 Amp/ Yellow 20 Amp/ Yellow 10 Amp/Red 15 Amp/Blue Items Fused IOD/Int Lighting/Radio Power Outlet Hazard Flasher MTV Electronic Automatic Transaxle (EATX) Horn Fog Lamp (Export Only) ASD/Fuel Pump A/C Clutch Stop Lamps MAINTAINING YOUR VEHICLE Interior Fuses The fuse access panel is behind the end cover at the left side of the instrument panel. To remove the panel, pull it out, as shown. A diagram identifying the components and circuits is located on the inside of the cover. 2 3 4 5 6 7 8 9 10 11 12 13 Interior Fuse Panel FUSE 1 Amp/Color 10 Amp/Red Items Fused Power Mirror/ Multifunction 14 15 16 I nf or mat i onPr ov i dedby : 20 Amp/ Yellow 20 Amp/ Yellow 15 Amp/Blue 10 Amp/Red 20 Amp/ Yellow 10 Amp/Red 15 Amp/Blue 10 Amp/Red 15 Amp/Blue 10 Amp/Red 10 Amp/Red 20 Amp/ Yellow 20 Amp/ Yellow 15 Amp/Blue 25 Amp/ Natural 197 Wiper Switch/Motor Radio/Power Sunroof Interior Lighting Airbag Run Only HVAC Blower Backup Switch/EBL/ Temp/Comp High Headlamp Airbag Run-Start ABS Engine Run Start ARKEM Run Start Ignition Off/Run/ Start Power Seat Height Adjust ARKEM Door Locks Exterior Lighting Headlamp 7 198 MAINTAINING YOUR VEHICLE 17 10 Amp/Red 18 10 Amp/Red 19 20 10 Amp/Red Spare Lt Low Beam Headlamp/ Headlamp Level Switch (Bux Only) Rt Low Beam Headlamp/ Headlamp Level Motor Fog lamps VEHICLE STORAGE If you will not be using your vehicle for more than 21 days you may want to take steps to preserve your battery. You may: • Disengage the mini fuse in the Power Distribution Center labeled IOD (Ignition Off-Draw). • Or, disconnect the negative cable from the battery. REPLACEMENT BULBS CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected. LIGHT BULBS — Inside Bulb No. ABS Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . LED Airbag Indicator . . . . . . . . . . . . . . . . . . . . . . . . LED Brake System Warning Indicator . . . . . . . . . . . . . LED Climate Controls . . . . . . . . . . . . . . . . . . . . . . . . LED Console Gear Selector . . . . . . . . . . . . . . . . . . . PC194 Dome Light. . . . . . . . . . . . . . . . . . . . . . . . . . . . T579 Front Fog Indicator . . . . . . . . . . . . . . . . . . . . . . LED High Beam Indicator . . . . . . . . . . . . . . . . . . . . PC194 Instrument Cluster Illumination . . . . . . . . . . . . PC194 Low Fuel Indicator. . . . . . . . . . . . . . . . . . . . . . . LED Low Oil Pressure Indicator . . . . . . . . . . . . . . . . . LED Rear Cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . T906 I nf or mat i onPr ov i dedby : MAINTAINING YOUR VEHICLE LIGHT BULBS — Inside Bulb No. Seat Belt Indicator . . . . . . . . . . . . . . . . . . . . . . . LED Security Alarm Indicator. . . . . . . . . . . . . . . . . . . LED Malfunction Indicator Light . . . . . . . . . . . . . . . . LED Turn Signal Indicator . . . . . . . . . . . . . . . . . . . . PC194 Voltage Indicator . . . . . . . . . . . . . . . . . . . . . . . . LED BULB REPLACEMENT Headlight Bulb Replacement CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. All the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved and should not be used for replacement. LIGHTS BULBS — Outside Bulb No. Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9007 Front Park/Turn Signal Light . . . . . . . . . . . . . 3457AK Front Side Marker Light. . . . . . . . . . . . . . . . . . . . 168 Front Fog Light . . . . . . . . . . . . . . . . . . . . . . . . . . 899 Center High Mounted Stop Light (CHMSL) . . . . . 921– W16W Rear Tail/Stop/Turn Signal Light . . . . . . 3157–P27/7W Backup Light . . . . . . . . . . . . . . . . . . . . . . 921–W16W License Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 199 1. Remove the three upper fascia screws. I nf or mat i onPr ov i dedby : 7 200 MAINTAINING YOUR VEHICLE 2. Remove two screws from the headlight assembly and remove the assembly from the vehicle. 3. Disconnect the electrical connector. 4. Remove the retaining ring and replace the bulb. NOTE: The headlight assembly is located to the fender by a molded pin. Pull the outboard side of the headlight straight out until the molded pin clears the fender, then slide the headlight out from behind the bumper fascia and grille. I nf or mat i onPr ov i dedby : CAUTION! During installation, be sure when tightening the inboard screw, to only tighten until the rubber grommet on the screw starts to compress against the headlamp module housing. MAINTAINING YOUR VEHICLE 201 Front Park/Turn Signal Lights Tail/Stop, Rear Turn Signals and Back-up Lights 1. Remove the headlight assembly 1. Open the trunk and move the trunk liner away from the rear light mounting area. 2. Twist the bulb socket 1/4 turn and remove. 2. Twist the bulb socket 1/4 turn to remove it from the housing. 3. Pull the bulb from the socket and replace. Front Sidemarker Light 3. Pull bulb from socket and replace 1. Remove the screws and push-pins from the front fender splash shield. 2. Reach between the fender and the splash shield, grasp the bulb and socket assembly and turn it counterclockwise. Remove the bulb and socket assembly from the light housing. Center High Mounted Stop Light 1. Twist the socket 1/4 turn and remove it from the housing. 2. Pull the bulb out of the socket and replace. 3. Pull the bulb out of the socket and replace the bulb. Reinstall the bulb and socket assembly and replace the fender splash shield. I nf or mat i onPr ov i dedby : 7 202 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) 2.0L Engines 87 Octane Engine Oil-With Filter 2.0 Liter Engines (SAE 5W-20, API Certified Engine Oil) Cooling System * 2.0 Liter Engines (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula), or equivalent. * Includes heater and coolant recovery bottle filled to MAX level. I nf or mat i onPr ov i dedby : U.S. Metric 12.5 Gallons 47.5 Liters 4.5 qts 4.3 Liters 6.5 qts 6.2 Liters MAINTAINING YOUR VEHICLE 203 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluids, Lubricants and Genuine Parts Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified SAE 5W-20 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395. Mopar 4105409 or equivalent. Refer to the Vehicle Emission Control Information label in the engine compartment. 87 Octane. Chassis Component Automatic Transmission Manual Transmission Fluid Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopart ATF+4 Automatic Transmission Fluid or equivalent. Mopart ATF+4 Automatic Transmission Fluid or equivalent. Mopart DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent. Mopart ATF+4 Automatic Transmission Fluid or equivalent I nf or mat i onPr ov i dedby : 7 I nf or mat i onPr ov i dedby : MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E m Emission Control System Maintenance . . . . . . 206 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 209 m Maintenance Schedules . . . . . . . . . . . . . . . . . . 206 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 218 C S H E D U L E S 8 I nf or mat i onPr ov i dedby : M A I N T E N A N C E 206 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability. More frequent mainS tenance may be needed for vehicles in severe operating C conditions such as dusty areas and very short trip H driving. E D U L E S 8 Inspection and service also should be done any time a malfunction is suspected. NOTE: Maintenance, replacement, or repair of the emission control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part which has been certified pursuant to U.S. EPA or, in the State of California, California Air Resources Board regulations. MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule “B”. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. • Day or night temperatures are below 32°F (0°C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16.2 km). • More than 50% of your driving is sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing.†L • Taxi, police or delivery service (commercial services).†L • Off-road or desert operation. I nf or mat i onPr ov i dedby : MAINTENANCE SCHEDULES • If equipped for and operating with E-85 (ethanol) fuel. 207 M CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the 9Maintenance Schedules9 section of this manual. At Each Stop for Fuel NOTE: IF ANY of these apply to you then flush and replace the engine coolant every 102,000 miles (163 000 km) or 60 months, whichever comes first, and follow schedule “B” of the 9Maintenance Schedules9 section of this manual. • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accuracy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. NOTE: Most vehicles are operated under the conditions listed for Schedule 9B9. Second is Schedule “A”. It is for vehicles that are not operated under any of the conditions listed under Schedule 9B9. Use the schedule that best describes your driving conditions. Where time and mileage are listed, follow the interval that occurs first. A I N T E N A N C E S C H E D U L • Check the windshield washer solvent and add if E S required. Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as required. I nf or mat i onPr ov i dedby : 8 M A I N T E N A N C E 208 MAINTENANCE SCHEDULES • Check the fluid levels of coolant reservoir, brake master cylinder, power steering and transaxle and add as needed. • Check all lights and all other electrical items for correct operation. • Check rubber seals on each side of the radiator for proper fit. S C H E D U L E S At Each Oil Change • Inspect the brake hoses. • Inspect the CV joints and front suspension components. • Check the automatic transaxle fluid level. • Check the manual transaxle fluid level and fill plug condition. • Check the coolant level, hoses, and clamps. • Change the engine oil filter. • Inspect the exhaust system. 8 I nf or mat i onPr ov i dedby : SCHEDULE “B” Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an L. Change the manual transaxle fluid every 48,000 miles (77 000 km) if the vehicle is usually operated under one or more of the conditions marked with an †. • Day or night temperatures are below 32°F (0°C). • Stop and go driving. • Extensive engine idling. 209 M E N A • If equipped for and operating with E-85 (ethanol) N C fuel. E • Off-road or desert operation. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the 9Maintenance Schedules9 section of this manual. S C H E D NOTE: IF ANY of these apply to you then flush and U replace the engine coolant every 102,000 miles (163 000 L E km) or 60 months, whichever comes first, and follow S schedule “B” of the 9Maintenance Schedules9 section of this manual. • Driving in dusty conditions. • Short trips of less than 10 miles (16.2 km). • More than 50% of your driving is sustained high speeds during hot weather, above 90°F (32°C). A • Taxi, police or delivery service (commercial services).† I N L T If none of these apply to you, then change your engine oil at every interval shown on schedule 9A9 of the 9Maintenance Schedules9 section of this manual. • Trailer towing.† L I nf or mat i onPr ov i dedby : 8 M 210 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Rotate tires. E Inspect the front brake pads and rear brake linings S C H E D U L E S 3,000 (5 000) X and rotors. Inspect and replace, if required, the make-up air filter (located inside the air cleaner). Inspect and replace, if required, the air cleaner filter. * 8 I nf or mat i onPr ov i dedby : 6,000 (10 000) X 9,000 (14 000) X X 12,000 (19 000) X 15,000 (24 000) X X X X X SCHEDULE “B” Miles (Kilometers ) Change engine oil and engine oil filter, if not replaced at 3 months.. Rotate tires. Inspect the front brake pads and rear brake linings and rotors. Replace air cleaner filter. Inspect the PCV valve and replace if necessary. * Adjust the generator belt tension. Replace the make-up air filter (located inside the air cleaner). Replace the spark plugs. Inspect the tie rod ends and boot seal. 18,000 (29 000) X X X I nf or mat i onPr ov i dedby : 21,000 (34 000) X 24,000 (38 000) X 27,000 (43 000) X X 211 M 30,000 (48 000) X X X X X X X X X A I N T E N A N C E S C H E D U L E S 8 M 212 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Rotate tires. E Inspect the front brake pads and rear brake linings S C H E D U L E S 33,000 (53 000) X and rotors. Inspect and replace, if necessary, the air cleaner filter. * Inspect and replace, if required, the make-up air filter (located inside the air cleaner). 8 I nf or mat i onPr ov i dedby : 36,000 (58 000) X X X 39,000 (62 000) X 42,000 (67 000) X 45,000 (72 000) X X X X X SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the front brake pads and rear brake linings and rotors. Replace air cleaner filter. Check and replace, if necessary, the PCV valve. *‡ Change the automatic transaxle fluid and adjust the bands.L Replace manual transaxle fluid.† Inspect the tie rod ends and boot seals. Replace the drive belts. Replace the make-up air filter (located inside the air cleaner). Replace the spark plugs and ignition cables. Flush and replace engine coolant at 60 months, if not done at 102,000 miles. 48,000 (77 000) X X 51,000 (82 000) X 54,000 (86 000 ) X X X 57,000 (91 000) X 60,000 (96 000) X X X X X X I nf or mat i onPr ov i dedby : 213 M X X X X X A I N T E N A N C E S C H E D U L E S 8 M 214 SCHEDULE “B” A I N Miles T ( Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Rotate tires. E Inspect the front brake pads and rear brake linings S C H E D U L E S 63,000 (101 000) X 66,000 (106 000 ) X X X and rotors. Inspect and replace, if necessary, the air cleaner filter. * Inspect and replace, if required, the make-up air filter (located inside the air cleaner). 8 I nf or mat i onPr ov i dedby : 69,000 (110 000 ) X 72,000 (115 000) X 75,000 (120 000) X X X X X SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the front brake pads and rear brake linings and rotors. Replace air cleaner filter. Inspect the PCV valve and replace if necessary. *‡ Inspect the tie rod ends and boot seals. Adjust the generator drive belt tension. Replace the make-up air filter (located inside the air cleaner). Replace the spark plugs. 78,000 (125 000) X 81,000 (130 000 ) X X I nf or mat i onPr ov i dedby : 84,000 (134 000 ) X X X 87,000 (139 000 ) X 215 M 90,000 (144 000) X X X A I N T E N A N C E X X X X X S C H E D U L E S X 8 M 216 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Rotate tires. E Inspect the front brake pads and rear brake linings S C H E D U L E S 8 93,000 (149 000) X and rotors. Inspect and replace, if necessary, the air cleaner filter. * Replace manual transaxle fluid.† Flush and replace the engine coolant, if not done at 60 months. Replace the engine timing belt. Inspect and replace, if required, the make-up air filter (located inside the air cleaner). I nf or mat i onPr ov i dedby : 96,000 (154 000) X 99,000 (158 000 ) X X 102,000 (163 000) X 105,000 (168 000) X X X X X X X X SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the front brake pads and rear brake linings and rotors. Inspect and replace, if necessary, the air cleaner filter. * Inspect the PCV valve and replace if necessary. *‡ Inspect and replace, if required, the make-up air filter (located inside the air cleaner). Replace the spark plugs and ignition cables. Replace the drive belts Flush and replace the engine coolant, if not done at 60 months. * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced. 217 M 108,000 (173 000) 111,000 (178 000) 114,000 (183 000 ) 117,000 (188 000) 120,000 (193 000) X X X X X X X X X X X X X X X L This maintenance is required only for police, taxi, limousine type operation, or trailer towing. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. † This maintenance is required only for police, taxi, limousine type operation, or trailer towing. I nf or mat i onPr ov i dedby : A I N T E N A N C E S C H E D U L E S 8 M 218 SCHEDULE “A” A I Schedule “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Rotate tires. S C H E D U L E S 8 6,000 (10 000) [6] X X Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the make-up air filter (located inside the air cleaner). Adjust generator drive belt tension 12,000 (19 000) [12] X X 18,000 (29 000) [18] X X X 24,000 (38 000) [24] X X 30,000 (48 000) [30] X X X X X X X I nf or mat i onPr ov i dedby : 36,000 (58 000) [36] X X X SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace, if necessary.* Flush and replace the engine coolant at 60 months, if not done at 102,000 miles. Replace the make-up air filter (located inside the air cleaner). Replace drive belts. 42,000 (67 000) [42] X X I nf or mat i onPr ov i dedby : 48,000 (77 000) [48] X X 54,000 (86 000) [54] X X X 60,000 (96 000) [60] X X 219 M 66,000 (106 000) [66] X X A I N T E N A N C E X X X X X S C H E D U L E S X 8 X M 220 SCHEDULE “A” A I N Miles T (Kilometers) E N A [Months] N C Change engine oil and engine oil filter. E Rotate tires. S C H E D U L E S 8 72,000 (115 000) Inspect the front brake pads and rear brake linings and rotors. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the make-up air filter (located inside the air cleaner). Adjust the generator drive belt tension. Replace engine timing belt. [72] X X X I nf or mat i onPr ov i dedby : 78,000 (125 000) [78] X X 84,000 (134 000) [84] X X 90,000 (144 000) [90] X X X 96,000 (154 000) [96] X X 102,000 (160 000) [102] X X X X X X X X X SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the front brake pads and rear brake linings and rotors. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the make-up air filter (located inside the air cleaner). Adjust the generator drive belt tension. Flush and replace the engine coolant, if not done at 60 months. * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced. I nf or mat i onPr ov i dedby : 108,000 (173 000) [108] X X X 114,000 (182 000) [114] X X 221 M 120,000 (192 000) [120] X X X X X X X X X X A I N T E N A N C E S C H E D U L E S 8 M 222 SCHEDULE “A” A I WARNING! N T E You can be badly injured working on or around a N motor vehicle. Do only that service work for which A you have the knowledge and the right equipment. If N C you have any doubt about your ability to perform a E service job, take your vehicle to a competent mechanic. S C H E D U L E S 8 I nf or mat i onPr ov i dedby : IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 ▫ Prepare For The Appointment . . . . . . . . . . . . 224 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 224 m Reporting Safety Defects . . . . . . . . . . . . . . . . . 229 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 229 m Publication Order Forms . . . . . . . . . . . . . . . . . 229 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 224 m Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 231 m If You Need Assistance . . . . . . . . . . . . . . . . . . 224 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . . 231 m Warranty Information . . . . . . . . . . . . . . . . . . . 227 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . 231 m Mopart Parts . . . . . . . . . . . . . . . . . . . . . . . . . 229 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . . 232 I nf or mat i onPr ov i dedby : 9 224 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem. Prepare A List Make a written list of your vehicle’s problems or the specific work you want done. If you’ve had an accident, or work done that is not on your maintenance log, let the service advisor know. Be Reasonable With Requests If you list a number of items, and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many dealers you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment. IF YOU NEED ASSISTANCE The manufacturer and its dealers are vitally interested in your satisfaction. We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service. The manufacturer’s dealers have the facilities, factory-trained technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. I nf or mat i onPr ov i dedby : IF YOU NEED CONSUMER ASSISTANCE • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center. Any communication to the Manufacturer’s Customer Center should include the following information: • Owner’s name and address • Owner’s telephone number (home and office) • Dealership name • Vehicle identification number • Vehicle delivery date and mileage DaimlerChrysler Motors Corporation Customer Center P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: (800) 992-1997 225 DaimlerChrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone —(800) 465–2001 In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY. I nf or mat i onPr ov i dedby : 9 226 IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date. If you have any questions about your service contract, call the manufacturer’s Service Contract National Customer Hotline at 1-800-521-9922. The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract. If you purchased a service contract that is not a manufacturer’s Service Contract, and you require service after your manufacturer’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased your new vehicle. Your dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. I nf or mat i onPr ov i dedby : IF YOU NEED CONSUMER ASSISTANCE 227 WARRANTY INFORMATION See your manufacturer’s Warranty Information Booklet for information on warranty coverage and transfer of warranty. 9 I nf or mat i onPr ov i dedby : 228 IF YOU NEED CONSUMER ASSISTANCE U.S. ONLY I nf or mat i onPr ov i dedby : IF YOU NEED CONSUMER ASSISTANCE MOPART PARTS Mopart fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, and the manufacturer. To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1-800-424-9393 (or 366-0123 in Washington DC area) or write to: NHTSA, U.S. Dept. of 229 Transportation, Washington DC 20590. You can also obtain other information about motor vehicle safety from the Hotline. In Canada: If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately. Canadian customers who wish to report a safety defect to the Canadian government should write to Transport Canada, Motor Vehicle Defect Investigations and Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B 3V9. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). I nf or mat i onPr ov i dedby : 9 230 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals. • Owner’s Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts. • Diagnostic Procedure Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance procedures as well as specifications, capabilities and safety tips. Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Or Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix problems on computercontrolled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-by-step troubleshooting and driveability procedures, proven diagnostic tests and a complete list of all tools and equipment. Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.ca/manuals I nf or mat i onPr ov i dedby : IF YOU NEED CONSUMER ASSISTANCE 231 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car. Traction Grades The traction grades, from highest to lowest, are A, B, and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. All Passenger Car Tires Must Conform to Federal Safety Requirements in Addition to These Grades. WARNING! Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. I nf or mat i onPr ov i dedby : The traction grade is based on braking (straightahead) traction tests and does not include cornering (turning) performance. 9 232 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. I nf or mat i onPr ov i dedby : WARNING! The temperature grade is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. INDEX 10 I nf or mat i onPr ov i dedby : 234 INDEX ABS (Anti-Lock Brake) System . . . . . . . . . . . . . 123 Adding Engine Coolant (Antifreeze) . . . . . . . . . 183 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Air Cleaner, Engine (Engine Air Cleaner Filter) . 175 Air Conditioning . . . . . . . . . . . . . . . . . . . . 103,177 Air Conditioning Controls . . . . . . . . . . . . . . . . 103 Air Conditioning Refrigerant . . . . . . . . . . . . . . 177 Air Conditioning System . . . . . . . . . . . . . . . . . 177 Air Pressure, Tires . . . . . . . . . . . . . . . . . . . . . . 133 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . 36 Airbag Light . . . . . . . . . . . . . . . . . . . . . . . 39,47,79 Airbag Maintenance . . . . . . . . . . . . . . . . . . . . . . 38 Airbag, Side . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Alarm, Panic . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Alarm System . . . . . . . . . . . . . . . . . . . . . . . . 22,79 Alignment and Balance . . . . . . . . . . . . . . . . . . 139 Alterations/Modifications, Vehicle . . . . . . . . . . . . 6 Antenna, Satellite Radio . . . . . . . . . . . . . . . . . . . 96 Antifreeze (Engine Coolant) . . . . . . . . . 182,202,203 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 Anti-Lock Brake System (ABS) . . . . . . . . . . . . . 123 Anti-Lock Warning Light . . . . . . . . . . . . . . . . . . 77 Anti-Theft Security Alarm . . . . . . . . . . . . . . . . . 22 Appearance Care . . . . . . . . . . . . . . . . . . . . . . . 191 Arming Theft System . . . . . . . . . . . . . . . . . . . . . 22 Ashtrays and Lighter . . . . . . . . . . . . . . . . . . . . . 70 Automatic Door Locks . . . . . . . . . . . . . . . . . . . . 16 Automatic Transaxle . . . . . . . . . . . 9,114,116,117,188 Fluid and Filter Changes . . . . . . . . . . . . . . . . 190 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . 188 Interlock System . . . . . . . . . . . . . . . . . . . . 14,116 Reset Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Selection Of Lubricant . . . . . . . . . . . . . . . . . 188 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Special Additives . . . . . . . . . . . . . . . . . . . . . 190 Ball Joints . . . . . . . . . . . . . . . . . . Battery . . . . . . . . . . . . . . . . . . . . . Keyless Transmitter Replacement Belts, Drive . . . . . . . . . . . . . . . . . Belts, Engine . . . . . . . . . . . . . . . . Body Mechanism Lubrication . . . . B-Pillar Location . . . . . . . . . . . . . Brake Fluid . . . . . . . . . . . . . . . . . I nf or mat i onPr ov i dedby : . . . . . . . . . . 178 . . . . . . . . . . 176 . . . . . . . . . . 21 . . . . . . . . . . 173 . . . . . . . . . . 174 . . . . . . . . . . 178 . . . . . . . . . . 128 . . . . . . . . . . 203 INDEX Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . 121 Brake System . . . . . . . . . . . . . . . . . . . . . . . 122,186 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . 187 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Warning Light . . . . . . . . . . . . . . . . . . . . . . . . 77 Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122,186 Brake/Transmission Interlock . . . . . . . . . . . . . . 116 Break-In Recommendations, New Vehicle . . . . . . 46 Bulb Replacement . . . . . . . . . . . . . . . . . . . 198,199 Calibration, Compass . . . . . . . . . . . . . . . . . . . . . 54 Capacities, Antifreeze (Engine Coolant) . . . . . . 202 Capacities, Fluid . . . . . . . . . . . . . . . . . . . . . . . 202 Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . 172 Carbon Monoxide Warning . . . . . . . . . . . . . . . 144 Cassette Tape and Player Maintenance . . . . . . . . 97 Cassette Tape Player . . . . . . . . . . . . . . . . . . . 83,86 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . 173 Caution, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . 46 235 CD Changer . . . . . . . . . . . . . . . . . . . . . . . 87,92,98 CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . 88,90 CD Player Maintenance . . . . . . . . . . . . . . . . . . 100 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . 101 Center High Mounted Stop Light . . . . . . . . . . . 201 Central Door Locks . . . . . . . . . . . . . . . . . . . . . . 15 Central Locking . . . . . . . . . . . . . . . . . . . . . . . . . 15 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . 152 Charging System Light . . . . . . . . . . . . . . . . . . . 79 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . 125 Check Engine Light (Malfunction Indicator Light) . . . . . . . . . . . . . . 167 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . . 39 Child Safety Locks . . . . . . . . . . . . . . . . . . . . . . . 17 Circuit Breakers . . . . . . . . . . . . . . . . . . . . . 195,197 Cleaning Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 194 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . 101 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Compact Disc Changer . . . . . . . . . . . . . . . . . . . 98 Compact Disc Maintenance . . . . . . . . . . . . . . . 100 I nf or mat i onPr ov i dedby : 10 236 INDEX Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . 135 Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Compass Calibration . . . . . . . . . . . . . . . . . . . . . 54 Compass Variance . . . . . . . . . . . . . . . . . . . . . . . 53 Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Contract, Service . . . . . . . . . . . . . . . . . . . . . . . 226 Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . 202,203 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . 181 Adding Coolant (Antifreeze) . . . . . . . . . . . . . 183 Coolant Level . . . . . . . . . . . . . . . . . . . . . 181,184 Disposal of Used Coolant . . . . . . . . . . . . . . . 184 Drain, Flush, and Refill . . . . . . . . . . . . . . . . . 182 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 Points to Remember . . . . . . . . . . . . . . . . 183,184 Pressure Cap . . . . . . . . . . . . . . . . . . . . . . . . 183 Rubber and Plastic Components . . . . . . . . . . 185 Selection of Coolant . . . . . . . . . . . . . . . . . . . 182 Corrosion Protection . . . . . . . . . . . . . . . . . . . . 191 Crankcase Emission Control System . . . . . . . . . 175 Cruise Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Cup Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Customer Assistance . . . . . . . . . . . . . . . . . . . . 224 Daytime Brightness, Interior Lights . . . . . . . . . . 61 Daytime Running Lights . . . . . . . . . . . . . . . . . . 62 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . 168 Defroster, Rear Window . . . . . . . . . . . . . . . . . . 110 Defroster, Windshield . . . . . . . . . . . . . . . 47,102,105 Deploying, Airbag . . . . . . . . . . . . . . . . . . . . . . . 36 Diagnostic System, Onboard . . . . . . . . . . . . . . . 166 Dimmer Control . . . . . . . . . . . . . . . . . . . . . . . . 60 Dimmer Switch, Headlight . . . . . . . . . . . . . . . . . 62 Disarming, Theft System . . . . . . . . . . . . . . . . . . 23 Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . 184 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Domelight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . 16 Downshifting . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Driving On Slippery Surfaces . . . . . . . . . . . . . . . . . . 158 Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . 55 Electronic Speed Control . . . . . . . . . . . . . . . . . . 65 I nf or mat i onPr ov i dedby : INDEX Emergency, In Case of Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . 155 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Emergency Trunk Release . . . . . . . . . . . . . . . . . 18 Emission Control System Maintenance . . . . 167,206 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Break-In Recommendations . . . . . . . . . . . . . . . 46 Checking Oil Level . . . . . . . . . . . . . . . . . . . . 169 Compartment . . . . . . . . . . . . . . . . . . . . . . . . 165 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . 144 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . 155 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 169,202,203 Oil Change Interval . . . . . . . . . . . . . . . . . . . 170 Oil Filler Cap . . . . . . . . . . . . . . . . . . . . . . . . 172 Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 Oil Selection . . . . . . . . . . . . . . . . . . . . . . . . . 171 Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 172 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . 150 Temperature Gauge . . . . . . . . . . . . . . . . . . . . 81 Timing Belt . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . 46,144 237 Exhaust Pipes . . . . . . . . . . . . . . . . . . . . . . . . . 180 Exhaust System . . . . . . . . . . . . . . . . . . . . . . . . 180 Extender, Seat Belt . . . . . . . . . . . . . . . . . . . . . . . 31 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Automatic Transaxle . . . . . . . . . . . . . . . . . . . 190 Engine Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 175 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . 173,203 Flashers Hazard Warning . . . . . . . . . . . . . . . . . . . . . . 150 Flooded Engine Starting . . . . . . . . . . . . . . . . . . 115 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . 202 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Fluid Level Checks Automatic Transaxle . . . . . . . . . . . . . . . . . . . 188 Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 190 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . 62,77 Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . . . 57 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 159 Front Suspension Ball Joints . . . . . . . . . . . . . . . 178 I nf or mat i onPr ov i dedby : 10 238 INDEX Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141,203 Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Filler Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Octane Rating . . . . . . . . . . . . . . . . . . . . . . . . 141 Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . 202 Fuel System Caution . . . . . . . . . . . . . . . . . . . . 143 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 150 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . 57 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 199 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Hood Prop . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Gas Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . 142 Gasoline/Oxygenate Blends . . . . . . . . . . . . . . . 142 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . 81 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Gearshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 General Information . . . . . . . . . . . . . . . . . . . . . . 13 Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 194 Ignition Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Wiring System . . . . . . . . . . . . . . . . . . . . . . . 175 Immobilizer . . . . . . . . . . . . . . . . . . . . . . . . . . 11,22 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . . 40 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . 51 Instrument Cluster . . . . . . . . . . . . . . . . . . 75,76,77 Instrument Panel and Controls . . . . . . . . . . . . . . 74 Instrument Panel Cover . . . . . . . . . . . . . . . . . . 194 Instrument Panel Lens Cleaning . . . . . . . . . . . . 195 Interior Appearance Care . . . . . . . . . . . . . . . . . 193 I nf or mat i onPr ov i dedby : INDEX Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 197 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Intermittent Wipers . . . . . . . . . . . . . . . . . . . . . . 64 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Jack Operation . . . . . . . . . . . . . . . . . . . . . . . . . 152 Jacking Instructions . . . . . . . . . . . . . . . . . . . . . 152 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 155 Key, Programming . . . . . . . . . . . . . . . . . . . . . . . 12 Key Release Button . . . . . . . . . . . . . . . . . . . . . . 10 Key, Replacement . . . . . . . . . . . . . . . . . . . . . . . 12 Key, Sentry . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Key-In Reminder . . . . . . . . . . . . . . . . . . . . . . . . 11 Keyless Entry System . . . . . . . . . . . . . . . . . . . . . 19 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Lane Change and Turn Signals . . . . . . . . . . . . . . 78 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . 24 LATCH (Lower Anchors and Tether for CHildren) . . . . . 42 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 141 Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 239 Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . 198,199 Lighter, Cigar . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . 39,47,79 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 77 Center Mounted Stop . . . . . . . . . . . . . . . . . . 201 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 62 Dimmer Switch, Headlight . . . . . . . . . . . . . 61,62 Dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Exterior Check . . . . . . . . . . . . . . . . . . . . . . . . 47 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62,77 Headlights On Reminder . . . . . . . . . . . . . . . . 62 High Beam Indicator . . . . . . . . . . . . . . . . . . . 78 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 61 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Lights On Reminder . . . . . . . . . . . . . . . . . . . . 62 Low Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Malfunction Indicator . . . . . . . . . . . . . . . . . . . 80 Map Reading . . . . . . . . . . . . . . . . . . . . . . . . . 60 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 I nf or mat i onPr ov i dedby : 10 240 INDEX Rear Servicing . . . . . . . . . . . . . . . . . . . . . . . 201 Rear Tail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . 79 Security Alarm . . . . . . . . . . . . . . . . . . . . . . . . 22 Side Marker . . . . . . . . . . . . . . . . . . . . . . . . . 201 Theft Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Turn Signal . . . . . . . . . . . . . . . . . . . . . 62,78,201 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Warning (Instrument Cluster Description) . . . . 77 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . . . 146 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Child Protection . . . . . . . . . . . . . . . . . . . . . . . 17 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Power Door . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . . 13 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 178 Maintenance . . . . . . . . . . . . . . . . . . . . . . . 169,206 Maintenance, Airbag . . . . . . . . . . . . . . . . . . . . . 38 Maintenance Free Battery . . . . . . . . . . . . . . . . . 176 Maintenance Procedures . . . . . . . . . . . . . . . . . . 169 Maintenance Schedule . . . . . . . . . . . . . . . . . . . 206 Schedule 9A9 . . . . . . . . . . . . . . . . . . . . . . . . . 218 Schedule 9B9 . . . . . . . . . . . . . . . . . . . . . . . . . 209 Maintenance, Sunroof . . . . . . . . . . . . . . . . . . . . 69 Malfunction Indicator Light . . . . . . . . . . . . . 80,167 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . 229 Manual Transaxle . . . . . . . . . . . . . . . 67,114,119,190 Downshifting . . . . . . . . . . . . . . . . . . . . . . . . 120 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . 190 Frequency of Fluid Change . . . . . . . . . . . . . . 191 Lubricant Selection . . . . . . . . . . . . . . . . . . . . 190 Map/Reading Lights . . . . . . . . . . . . . . . . . . . . . 60 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . . 187 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Compass/Temperature . . . . . . . . . . . . . . . . . . 51 Electric Remote . . . . . . . . . . . . . . . . . . . . . . . 55 Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Modifications/Alterations, Vehicle . . . . . . . . . . . . 6 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . 168,229 Multi-Function Control Lever . . . . . . . . . . . . . 61,62 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . 24 I nf or mat i onPr ov i dedby : INDEX Odometer Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 169,202 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Change Interval . . . . . . . . . . . . . . . . . . . . . . 170 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Identification Logo . . . . . . . . . . . . . . . . . . . . 172 Materials Added to . . . . . . . . . . . . . . . . . . . . 172 Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Recommendation . . . . . . . . . . . . . . . . . . 171,202 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Oil Pressure Light . . . . . . . . . . . . . . . . . . . . . . . 78 Onboard Diagnostic System . . . . . . . . . . . . 166,167 Operator Manuals (Owner’s Manuals) . . . . . . . . . 4 Outside Air Intake . . . . . . . . . . . . . . . . . . . 103,109 Outside Rearview Mirrors . . . . . . . . . . . . . . . . . 54 Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Overheating, Engine . . . . . . . . . . . . . . . . . . . . . 150 Owner’s Manual . . . . . . . . . . . . . . . . . . . . . . 4,229 241 Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . 121 Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . 101 Placard, Tire and Loading Information . . . . . . . 128 Power Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Steering . . . . . . . . . . . . . . . . . . . . . . . . . 124,178 Steering, Checking . . . . . . . . . . . . . . . . . . . . 178 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Power Steering Fluid . . . . . . . . . . . . . . . . . . . . 203 Pregnant Women and Seat Belts . . . . . . . . . . . . . 30 Preparation for Jacking . . . . . . . . . . . . . . . . . . . 152 Programming Transmitters . . . . . . . . . . . . . . . . . 20 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . 135 Radio Broadcast Signals . . . . . . . . . . . . . . . . . . . 82 Radio Operation . . . . . . . . . . . . . . . . . . . . . . 83,88 Radio, Satellite . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Radio (Sound Systems) . . . . . . . . . . . . . . . 82,83,88 I nf or mat i onPr ov i dedby : 10 242 INDEX Rear Window Defroster . . . . . . . . . . . . . . . . . . 110 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . 56 Recommended Fluids, Lubricants and Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 Recreational Towing . . . . . . . . . . . . . . . . . . . . . 148 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . 142 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 Release, Hood . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . . 19 Remote Trunk Release . . . . . . . . . . . . . . . . . . . . 18 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . 198 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . 12 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . 168 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . 138 Reporting Safety Defects . . . . . . . . . . . . . . . . . 229 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . 141 Safety Checks Inside Vehicle . . . . . . . . . . . . . . . 47 Safety Checks Outside Vehicle . . . . . . . . . . . . . . 47 Safety Defects, Reporting . . . . . . . . . . . . . . . . . 229 Safety Information, Tire . . . . . . . . . . . . . . . . . . 124 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Satellite Radio . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 96 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Adjustable Upper Shoulder Anchorage . . . . . . 28 And Pregnant Women . . . . . . . . . . . . . . . . . . 30 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . 39 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 195 Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Untwisting Procedure . . . . . . . . . . . . . . . . . . . 29 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . 57 Rear Folding . . . . . . . . . . . . . . . . . . . . . . . . . 57 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Security Alarm (Theft Alarm) . . . . . . . . . . . . . 22,79 Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . 11,22 Sentry Key Programming . . . . . . . . . . . . . . . . . . 12 Service Assistance . . . . . . . . . . . . . . . . . . . . . . 224 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . 226 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . 229 Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . 82 Shift Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 I nf or mat i onPr ov i dedby : INDEX Shift Speeds, Manual Transaxle . . . . . . . . . . . . 120 Shoulder Belt Upper Anchorage . . . . . . . . . . . . . 28 Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Side Window Demisters . . . . . . . . . . . . . . . 103,109 Slippery Surfaces, Driving On . . . . . . . . . . . . . 158 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . 135,136 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Speed Control . . . . . . . . . . . . . . . . . . . . . . . . 65,81 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Speedometer and Odometer . . . . . . . . . . . . . . 75,76 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Engine Fails to Start . . . . . . . . . . . . . . . . . . . 115 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 114 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Wheel Lock . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . . . 198 Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Sunroof Maintenance . . . . . . . . . . . . . . . . . . . . . 69 Supplemental Restraint System - Airbag . . . . . . . 31 Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . 172 243 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Temperature Control, Automatic . . . . . . . . . . . . 101 Temperature Gauge, Engine Coolant . . . . . . . 81,151 Theft Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Theft System . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Theft System Arming . . . . . . . . . . . . . . . . . . . . . 22 Theft System Disarming . . . . . . . . . . . . . . . . . . . 23 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 64 Tire and Loading Information Placard . . . . . . . 128 Tire Identification Number (TIN) . . . . . . . . . . . 127 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . 124 Tire Safety Information . . . . . . . . . . . . . . . . . . . 124 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 47,132,231 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 132 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Compact Spare . . . . . . . . . . . . . . . . . . . . . . . 135 General Information . . . . . . . . . . . . . . . . . . . 132 High Speed . . . . . . . . . . . . . . . . . . . . . . . . . 134 Inflation Pressures . . . . . . . . . . . . . . . . . . . . 133 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 I nf or mat i onPr ov i dedby : 10 244 INDEX Load Capacity . . . . . . . . . . . . . . . . . . . . 128,129 Quality Grading . . . . . . . . . . . . . . . . . . . . . . 231 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 138 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 124,132 Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Tread Wear Indicators . . . . . . . . . . . . . . . . . . 137 Towing Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . . 160 Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Recreational . . . . . . . . . . . . . . . . . . . . . . . . . 148 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . 146 Minimum Requirements . . . . . . . . . . . . . . . . 147 Trailer and Tongue Weight . . . . . . . . . . . . . . 147 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Trailer Towing Guide . . . . . . . . . . . . . . . . . . . . 147 Trailer Weight . . . . . . . . . . . . . . . . . . . . . . . . . 147 Transaxle Automatic . . . . . . . . . . . . . . . . . 9,114,116,117,188 Manual . . . . . . . . . . . . . . . . . . . 10,67,114,119,190 Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Selection of Lubricant . . . . . . . . . . . . . . . . . . 188 Transmitter Battery Service . . . . . . . . . . . . . . . . 21 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . 45 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . 137 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Trip Odometer Reset Button . . . . . . . . . . . . . . . . 80 Trunk Release Button . . . . . . . . . . . . . . . . . . . . . 18 Trunk Release, Emergency . . . . . . . . . . . . . . . . . 18 Trunk Release Remote Control . . . . . . . . . . . . . . 18 Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 62,78 Underhood Fuses . . . . . . . . . . . . . . . . . . . . . . . 195 Uniform Tire Quality Grades . . . . . . . . . . . . . . 231 Untwisting Procedure, Seat Belt . . . . . . . . . . . . . 29 Vacuum/Vapor Harnesses . . . . . . . . . . . . . . . . 185 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 53 Vehicle Identification Number . . . . . . . . . . . . . . . 6 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . 129,146 Vehicle Modifications/Alterations . . . . . . . . . . . . 6 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . . 198 I nf or mat i onPr ov i dedby : INDEX Warning Lights (Instrument Cluster Description) . 77 Warnings and Cautions . . . . . . . . . . . . . . . . . . . . 6 Warranty Information . . . . . . . . . . . . . . . . . . . . 227 Washer, Adding Fluid . . . . . . . . . . . . . . . . . . . 180 Washers, Windshield . . . . . . . . . . . . . . . . . . . . . 63 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . 192 Wheel Alignment and Balance . . . . . . . . . . . . . 139 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . 193 Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . . . 69 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . 109 Windows Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Windshield Washer Aiming . . . . . . . . . . . . . . . 180 Windshield Washers . . . . . . . . . . . . . . . . . . . . . 63 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 Windshield Wiper Blades . . . . . . . . . . . . . . . . . 179 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . 63 Wiper Blade Replacement . . . . . . . . . . . . . . . . . 179 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . 64 Wiring, Ignition . . . . . . . . . . . . . . . . . . . . . . . . 175 I nf or mat i onPr ov i dedby : 245 10 246 INDEX I nf or mat i onPr ov i dedby :