Fiat - 500C - Owners Manual - 2015 - 2015 (3)

2015 FIAT 500 FIAT 500 2015 OWNER’S MANUAL Chrysler Group LLC 15FF500-126-AB Second Edition Rev 1 Printed in U.S.A. I nf or mat i onPr ovi dedby: VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated nondrinking driver, call a cab, a friend, or use public transportation. WARNING! Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive. This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle. Chrysler Group LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured. FIAT is a registered trademark of Fiat Group Marketing & Corporate Communication S.p.A., used under license by Chrysler Group LLC. Copyright © 2014 Chrysler Group LLC I nf or mat i onPr ovi dedby: INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible. The negative power connection should be made to body sheet metal adjacent to the negative battery connection. This connection should not be fused. Antennas for two-way radios should be mounted on the roof or the rear area of the vehicle. Care should be used in mounting antennas with magnet bases. Magnets may affect the accuracy or operation of the compass on vehicles so equipped. The antenna cable should be as short as practical and routed away from the vehicle wiring when possible. Use only fully shielded coaxial cable. Carefully match the antenna and cable to the radio to ensure a low Standing Wave Ratio (SWR). Mobile radio equipment with output power greater than normal may require special precautions. All installations should be checked for possible interference between the communications equipment and the vehicle’s electronic systems. SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 4 5 STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 5 6 WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 6 7 MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351 7 8 MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411 8 9 IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 9 10 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 10 I nf or mat i onPr ovi dedby: I nf or mat i onPr ovi dedby: INTRODUCTION CONTENTS ! INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 ! VEHICLE IDENTIFICATION NUMBER . . . . . . . .7 ! HOW TO USE THIS MANUAL . . . . . . . . . . . . . .5 ! VEHICLE MODIFICATIONS/ALTERATIONS . . . .8 ! WARNINGS AND CAUTIONS . . . . . . . . . . . . . .7 I nf or mat i onPr ovi dedby: 1 4 INTRODUCTION INTRODUCTION The enclosed Warranty Information lists the services that FIAT Group Automobiles offers to its customers: Congratulations on selecting your new vehicle. Be assured that it represents precision workmanship, distinc- • The Warranty Certificate with terms and conditions for tive styling, and high quality - all essentials that are maintaining its validity traditional to our vehicles. • The range of additional services available to FIAT This Owner’s Manual has been prepared with the assisGroup Automobiles customers tance of service and engineering specialists to acquaint NOTE: After reviewing the owner information, it you with the operation and maintenance of your vehicle. should be stored in the vehicle for convenient referencIt is supplemented by Warranty Information, and various ing and remain with the vehicle when sold. customer-oriented documents. Please take the time to read these publications carefully. Following the instruc- When it comes to service, remember that your authorized tions and recommendations in this manual will help dealer knows your vehicle best, has factory-trained techassure safe and enjoyable operation of your vehicle. nicians and genuine parts, and cares about your satisfaction. I nf or mat i onPr ovi dedby: INTRODUCTION 5 HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects. Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual: I nf or mat i onPr ovi dedby: 1 6 INTRODUCTION I nf or mat i onPr ovi dedby: INTRODUCTION 7 WARNINGS AND CAUTIONS 1 This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears engraved on the right front door sill under the sill scuff plate, on an adhesive label applied to the right door opening on the B-Pillar, on the vehicle registration and title. I nf or mat i onPr ovi dedby: Vehicle Identification Number 8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS ! A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .11 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .11 ▫ Locking Doors With A Key. . . . . . . . . . . . . . . .13 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .13 ! SENTRY KEY® . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . .14 ▫ General Information . . . . . . . . . . . . . . . . . . . .15 ! REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 ▫ Remote Key Unlock, Driver Door/All Doors 1st Press . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 ▫ To Lock The Doors And Liftgate . . . . . . . . . . . .16 ▫ Programming Additional Transmitters. . . . . . . .16 ▫ Transmitter Battery Replacement . . . . . . . . . . .16 ▫ General Information . . . . . . . . . . . . . . . . . . . .18 ! DOOR LOCKS . . . . . . . . . . . . . . . . . . . . . . . . .19 ▫ Power Door Locks — If Equipped . . . . . . . . . .21 ▫ Auto Door Locks . . . . . . . . . . . . . . . . . . . . . .21 ▫ To Unlock The Doors And Liftgate . . . . . . . . . .16 ! POWER WINDOWS . . . . . . . . . . . . . . . . . . . . .22 I nf or mat i onPr ovi dedby: 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Power Window Switches . . . . . . . . . . . . . . . . .22 ▫ Transporting Pets . . . . . . . . . . . . . . . . . . . . . .74 ▫ Auto-Down . . . . . . . . . . . . . . . . . . . . . . . . . .23 ! ENGINE BREAK-IN RECOMMENDATIONS . . . .74 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .23 ! SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . . .75 ! LIFTGATE . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 ▫ Transporting Passengers. . . . . . . . . . . . . . . . . .75 ! OCCUPANT RESTRAINT SYSTEMS . . . . . . . . . .25 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .76 ▫ Important Safety Precautions . . . . . . . . . . . . . .25 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 ▫ Seat Belt Systems . . . . . . . . . . . . . . . . . . . . . .27 ▫ Supplemental Restraint System (SRS) . . . . . . . .39 ▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . .55 ▫ Periodic Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . .79 I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 The vehicle is supplied with a code card containing key The key fob contains the Remote Keyless Entry (RKE) code numbers to order duplicate keys, and the authotransmitter with an integrated key. To use the mechanical rized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can key simply push the mechanical key release button. be used to order duplicate keys. A WORD ABOUT YOUR KEYS Ignition Key Removal 1. Place the shift lever in PARK (if equipped with an automatic transmission). 2. Rotate the key to the OFF/LOCK position. 3. Remove the key from the ignition switch lock cylinder. Mechanical Key Release Button I nf or mat i onPr ovi dedby: 2 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignition Switch Positions 1 — STOP (OFF/LOCK) 2 — MAR (ACC/ON/RUN) 3 — AVV (START) • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK and remove the Key Fob from the vehicle. When leaving the vehicle, always lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector. • Do not leave the Key Fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle. (Continued) I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key-In-Ignition Reminder WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Opening the driver’s door when the key is in the ignition and the ignition switch position is OFF/LOCK sounds a signal to remove the key. SENTRY KEY® CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. Locking Doors With A Key You can insert the key with either side up. To lock the door, turn the key to the left. To unlock the door, turn the key to the right. Refer to “Body Lubrication” in “Maintaining Your Vehicle” for maintenance procedures. The Sentry Key® Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys which have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation. Therefore, only keys that are programmed to the vehicle can be used to start and operate the vehicle. I nf or mat i onPr ovi dedby: 2 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A key which has not been programmed is also Replacement Keys considered an invalid key, even if it is cut to fit the NOTE: Only keys that have been programmed to the ignition switch lock cylinder for that vehicle. vehicle electronics can be used to start the vehicle. Once If the Vehicle Security Light is on after the key is turned a Sentry Key® has been programmed to a vehicle, it to the ON/RUN position, it indicates that there is a cannot be programmed to any other vehicle. When having the Sentry Key® Immobilizer System serviced, bring problem with the electronics. all vehicle keys with you to an authorized dealer. CAUTION! • Always remove the Sentry Key® from the vehicle and lock all doors when leaving the vehicle unattended. • The Sentry Key® Immobilizer system is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. At the time of purchase, the original owner is provided with a five digit Personal Identification Number (PIN). This PIN is required for authorized dealer replacement of keys. Duplication of keys may be performed at an authorized dealer. All of the keys provided with your new vehicle have been programmed to the vehicle electronics. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 General Information The Sentry Key® system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 2 • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Remote Keyless Entry Transmitter With Mechanical Key Release Button REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED NOTE: The line of transmission must not be blocked This system allows you to lock or unlock the doors and with metal objects. liftgate from distances up to approximately 66 ft (20 m) using a hand-held Remote Keyless Entry (RKE) transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system. I nf or mat i onPr ovi dedby: 16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock The Doors And Liftgate To Lock The Doors And Liftgate Push and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice, within five seconds, to unlock all doors and the liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Push and release the LOCK button on the RKE transmitter to lock all doors and the liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Remote Key Unlock, Driver Door/All Doors 1st Press This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the UNLOCK button on the RKE transmitter. To change the current setting, refer to “Personal Settings (CustomerProgrammable Features)” in “Understanding Your Instrument Panel” for further information. Programming Additional Transmitters Refer to Sentry Key® “Customer Key Programming.” If you do not have a programmed RKE transmitter, contact your authorized dealer for details. Transmitter Battery Replacement NOTE: Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate The recommended replacement battery is CR2032. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 1. Push the mechanical key release button and release the 2. Rotate the screw located on the side of the Key Fob mechanical key to access the battery case screw lousing a small screwdriver. cated on the side of the Key Fob. 2 Key Fob Screw Location Mechanical Key Release Button I nf or mat i onPr ovi dedby: 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Take out the battery case. Remove and replace the General Information battery observing its polarity. This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Battery Case Removed 4. Refit the battery case inside the Key Fob and turn the screw to lock it into place. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 If your RKE transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years. 2 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. DOOR LOCKS The door locks can be manually locked or unlocked from inside the vehicle by using the door handle. If the door handle is pushed a red lock indicator will show on the door handle (indicating locked) when the door is closed, the door will lock. I nf or mat i onPr ovi dedby: Driver’s Door Lock Handle 20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • For personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • Before exiting a vehicle, always turn the ignition to the OFF/LOCK position, apply the parking brake, shift the transmission into REVERSE gear, and remove the Key Fob from the vehicle. When leaving the vehicle, always lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector. • Do not leave the Key Fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle. (Continued) CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Power Door Locks — If Equipped A power door lock switch is incorporated into the driver door handle. Push or pull the handle to lock or unlock the doors and liftgate. If the driver’s door handle is pushed a red lock indicator will show on the driver’s door handle (indicating locked) when the door is closed, the door will lock. 2 NOTE: To prevent the key from being locked in the vehicle, the doors will automatically unlock if the driver’s door handle is pushed when the key is in the ignition. Driver’s Power Door Lock Handle Auto Door Locks When enabled, the door locks will lock automatically when the vehicles speed exceeds 15 mph (24 km/h). I nf or mat i onPr ovi dedby: 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To change the setting proceed as follows: POWER WINDOWS 1. Briefly push the MENU button to enter the MENU Power Window Switches screen. There are single window controls located on the shifter or DOWN button to highlight bezel, below the climate controls, which operate the 2. Push the UP “Auto Door Locks”. Push the MENU button, use driver and passenger door windows. The window conor DOWN buttons to turn setting ON trols will operate when the ignition switch is in the the UP ON/RUN position. or OFF 3. Briefly push the MENU button to go back to the menu screen, or push and hold the MENU button (approximately one second) to go back to the main screen without storing the settings. NOTE: Use the Automatic Door Locks feature in accordance with local laws. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” in your owner manual on your DVD for further information. WARNING! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the Key Fob in or near the vehicle, or in a location accessible to children. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Auto-Down The driver’s door window switch has an Auto-Down feature. Push the window switch for approximately one second, release, and the window will go down automatically. To cancel the Auto-Down movement, operate the switch in either the up or down direction and release the switch. Wind Buffeting Power Window Switches Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. I nf or mat i onPr ovi dedby: 2 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE To unlock the liftgate, use the Remote Keyless Entry (RKE) transmitter or activate the power door lock switches located on the driver door handle. To open the liftgate, squeeze the liftgate release handle and pull the liftgate open with one fluid motion. Liftgate Handle I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 OCCUPANT RESTRAINT SYSTEMS WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. Do not use the recirculation mode. Some of the most important safety features in your vehicle are the restraint systems: • Seat Belt Systems • Supplemental Restraint Systems (SRS) Air Bags • Child Restraints Important Safety Precautions Please pay close attention to the information in this section. It tells you how to use your restraint system NOTE: Gas props support the liftgate in the open posi- properly, to keep you and your passengers as safe as tion. However, because the gas pressure drops with possible. temperature, it may be necessary to assist the props when opening the liftgate in cold weather. I nf or mat i onPr ovi dedby: 2 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the 5. You should read the instructions provided with your risk of harm from a deploying air bag: child restraint to make sure that you are using it properly. 1. Children 12 years old and under should always ride 6. All occupants should always wear their lap and buckled up in a vehicle with a rear seat. shoulder belts properly. 2. If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, 7. The driver and front passenger seats should be moved back as far as practical to allow the Advanced Front move the seat as far back as possible and use the proper child restraint. (Refer to “Child Restraints”) Air Bags room to inflate. 3. Children that are not big enough to wear the vehicle 8. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the seat belt properly (Refer to #Child Restraints#) should be secured in a vehicle with a rear seat in child side air bags will inflate forcefully into the space between you and the door and you could be injured. restraints or belt-positioning booster seats. Older children who do not use child restraints or belt9. If the air bag system in this vehicle needs to be positioning booster seats should ride properly buckled modified to accommodate a disabled person, contact up in a vehicle with a rear seat. the Customer Center. Phone numbers are provided under #If You Need Assistance.# 4. Never allow children to slide the shoulder belt behind them or under their arm. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint. • Only use rear-facing child restraint in a vehicle with a rear seat. ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Enhanced Seat Belt Use Reminder System (BeltAlert) BeltAlert is a feature intended to remind the driver and outboard front passenger (if equipped with outboard front passenger BeltAlert) to buckle their seat belts. The feature is active whenever the ignition Seat Belt Systems switch is in the START or ON/RUN position. If the Buckle up even though you are an excellent driver, even driver or outboard front seat passenger is unbelted, on short trips. Someone on the road may be a poor driver the Seat Belt Reminder Light will turn on and remain and could cause a collision that includes you. This can on until both outboard front seat belts are buckled. happen far away from home or on your own street. The BeltAlert warning sequence begins after the vehicle Research has shown that seat belts save lives, and they speed is over 5 mph (8 km/h) by blinking the Seat Belt can reduce the seriousness of injuries in a collision. Some Reminder Light and sounding an intermittent chime. of the worst injuries happen when people are thrown Once the sequence starts, it will continue for the entire from the vehicle. Seat belts reduce the possibility of duration or until the respective seat belts are buckled. I nf or mat i onPr ovi dedby: 2 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE After the sequence completes, the Seat Belt Reminder Light remains illuminated until the respective seat belts are buckled. The driver should instruct all other occupants to buckle their seat belts. If an outboard front seat belt is unbuckled while traveling at speeds greater than 5 mph (8 km/h), BeltAlert will provide both audio and visual notification. The outboard front passenger seat BeltAlert is not active when the outboard front passenger seat is unoccupied. BeltAlert may be triggered when an animal or heavy object is on the outboard front passenger seat or when the seat is folded flat (if equipped). It is recommended that pets be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts, and cargo is properly stowed. NOTE: If BeltAlert has been deactivated, the Seat Belt Reminder Light will continue to illuminate while the driver’s or outboard front passenger’s (if equipped with BeltAlert) seat belt remains unbuckled. Lap/Shoulder Belts All seating positions in your vehicle are equipped with lap/shoulder belts. The seat belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoulder part of the seat belt to move freely with you under normal conditions. However, in a collision the seat belt will lock and reduce your risk of striking the inside of the vehicle or being thrown out of the vehicle. BeltAlert can be activated or deactivated by your authorized dealer. Chrysler Group LLC does not recommend deactivating BeltAlert. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! WARNING! (Continued) • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags. • In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of the seat belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. (Continued) (Continued) I nf or mat i onPr ovi dedby: 2 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • A lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • A twisted seat belt may not protect you properly. In a collision, it could even cut into you. Be sure the seat belt is flat against your body, without twists. If you can’t straighten a seat belt in your vehicle, take it to your authorized dealer immediately and have it fixed. • A seat belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your seat belt into the buckle nearest you. • A seat belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A seat belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A seat belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the seat belt over your shoulder so that your strongest bones will take the force in a collision. (Continued) I nf or mat i onPr ovi dedby: (Continued) THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Lap/Shoulder Belt Operating Instructions WARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. • A frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the seat belt system. Seat belt assemblies must be replaced after a collision. 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the seat belt. Slide the latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. I nf or mat i onPr ovi dedby: 2 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pulling Out The Latch Plate Inserting Latch Plate Into Buckle 3. When the seat belt is long enough to fit, insert the latch 4. Position the lap belt so that it is snug and lies low plate into the buckle until you hear a “click.” across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding under the seat belt in a collision. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 6. To release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180° to create a fold that begins immediately above the latch plate. 5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. Positioning The Lap Belt I nf or mat i onPr ovi dedby: 2 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted. Seat Belt Extender If a seat belt is not long enough to fit properly, even when the webbing is fully extended and the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a Seat Belt Extender. The Seat Belt Extender should be used only if the existing seat belt is not long enough. When the Seat Belt Extender is not required for a different occupant, it must be removed. WARNING! • ONLY use a Seat Belt Extender if it is physically required in order to properly fit the original seat belt system. DO NOT USE the Seat Belt Extender if, when worn, the distance between the front edge of the Seat Belt Extender buckle and the center of the occupant’s body is LESS than 6 inches. • Using a Seat Belt Extender when not needed can increase the risk of serious injury or death in a collision. Only use the Seat Belt Extender when the lap belt is not long enough and only use in the recommended seating positions. Remove and store the Seat Belt Extender when not needed. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be We recommend that pregnant women use the seat belts worn snugly and positioned properly. throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. The pretensioners are triggered by the Occupant Restraint Controller (ORC). Like the air bags, the pretenPregnant women should wear the lap part of the seat belt sioners are single use items. A deployed pretensioner or across the thighs and as snug across the hips as possible. a deployed air bag must be replaced immediately. Keep the seat belt low so that it does not come across the abdomen. That way the strong bones of the hips will take Energy Management Feature the force if there is a collision. This vehicle has a seat belt system with an Energy Management feature in the front seating positions that Seat Belt Pretensioner The front seat belt system is equipped with pretensioning may help further reduce the risk of injury in the event of devices that are designed to remove slack from the seat a collision. This seat belt system has a retractor assembly belt in the event of a collision. These devices may that is designed to release webbing in a controlled improve the performance of the seat belt by removing manner. Seat Belts And Pregnant Women slack from the seat belt early in a collision. Pretensioners work for all size occupants, including those in child restraints. I nf or mat i onPr ovi dedby: 2 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Switchable Automatic Locking Retractor (ALR) — If Equipped The seat belts in the passenger seating positions may be equipped with a switchable Automatic Locking Retractor (ALR) which is used to secure a child restraint system. For additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt” under the “Child Restraints” section of this manual. The table below defines the type of feature for each seating position. • Lower Anchorage Symbol 2 anchorages per seating position • I nf or mat i onPr ovi dedby: Top Tether Anchorage Symbol THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 In Automatic Locking Mode, the shoulder belt is automatically pre locked. The seat belt will still retract to First Row remove any slack in the shoulder belt. The Automatic Second Locking Mode is available on all passenger seating Row positions with a combination lap/shoulder belt. Use the Automatic Locking Mode anytime a child restraint is • N/A — Not Applicable installed in a seating position that has a seat belt with this • ALR — Automatic Locking Retractor feature. Children 12 years old and under should always If the passenger seating position is equipped with an be properly restrained in a vehicle with a rear seat. ALR and is being used for normal usage: Driver N/A ALR Center N/A N/A Passenger ALR ALR Only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the ALR. If the ALR is activated, you will hear a clicking sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfort- ably wrap around the occupant’s mid-section. Slide the latch plate into the buckle until you hear a #click.# WARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint. • Only use rear-facing child restraint in a vehicle with a rear seat. I nf or mat i onPr ovi dedby: 2 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Engage The Automatic Locking Mode WARNING! 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire seat belt is extracted. 3. Allow the seat belt to retract. As the seat belt retracts, you will hear a clicking sound. This indicates the seat belt is now in the Automatic Locking Mode. How To Disengage The Automatic Locking Mode Unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the Automatic Locking Mode and activate the vehicle sensitive (emergency) locking mode. • The seat belt assembly must be replaced if the switchable Automatic Locking Retractor (ALR) feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual. • Failure to replace the seat belt assembly could increase the risk of injury in collisions. • Do not use the Automatic Locking Mode to restrain occupants who are wearing the seat belt or children who are using booster seats. The locked mode is only used to install rear-facing or forward-facing child restraints that have a harness for restraining the child. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Supplemental Restraint System (SRS) Air Bag System Components • Supplemental Knee Air Bag • Front and Side Impact Sensors Your vehicle may be equipped with the following air bag • Seat Belt Pretenioners system components: • Seat Belt Buckle Switch • Occupant Restraint Controller (ORC) • Seat Track Position Sensors • Air Bag Warning Light Advanced Front Air Bags • Steering Wheel and Column This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat • Instrument Panel belt restraint systems. The driver’s Advanced Front Air • Knee Impact Bolsters Bag is mounted in the center of the steering wheel. The passenger’s Advanced Front Air Bag is mounted in the • Advanced Front Air Bags instrument panel, above the glove compartment. The • Supplemental Side Air Bags words SRS AIRBAG are embossed on the air bag covers. I nf or mat i onPr ovi dedby: 2 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Advanced Front Air Bag And Knee Bolster Locations 1 — Driver And Passenger Advanced Front Air Bags 2 — Passenger Knee Impact Bolster 3 — Supplemental Driver Side Knee Air Bag/Driver Knee Impact Bolster • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint. • Only use a rear-facing child restraint in a vehicle with a rear seat. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 the driver or front passenger seat belt is buckled. The seat belt buckle switch may adjust the inflation rate of the The Advanced Front Air Bag system has multistage Advanced Front Air Bags. driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as WARNING! determined by the Occupant Restraint Controller (ORC), which may receive information from the front impact • No objects should be placed over or near the air sensors or other system components. bag on the instrument panel or steering wheel, Advanced Front Air Bag Features The first stage inflator is triggered immediately during an impact that requires air bag deployment. A low energy output is used in less severe collisions. A higher energy output is used for more severe collisions. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Air Bags based upon seat position. This vehicle may be equipped with a driver and/or front passenger seat belt buckle switch that detects whether because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bags to inflate. • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating. I nf or mat i onPr ovi dedby: (Continued) 2 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, air bags won’t deploy at all. Always wear your seat belts even though you have air bags. Advanced Front Air Bag Operation Advanced Front Air Bags are designed to provide additional protection by supplementing the seat belts. Advanced Front Air Bags are not expected to reduce the risk of injury in rear, side, or rollover collisions. The Advanced Front Air Bags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, Advanced Front Air Bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all collisions, and also are needed to help keep you in position, away from an inflating air bag. When the ORC detects a collision requiring the Advanced Front Air Bags, it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the Advanced Front Air Bags. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The Advanced Front Air Bags fully inflate in less time than it takes to blink your eyes. The air bags then quickly deflate while helping to restrain the driver and front passenger. Supplemental Driver Knee Air Bag This vehicle is equipped with a Supplemental Driver Knee Air Bag mounted in the instrument panel below the steering column. The Supplemental Driver Knee Air Bag provides enhanced protection during a frontal impact by working Knee Impact Bolsters together with the seat belts, pretensioners, and Advanced The Knee Impact Bolsters help protect the knees of the Front Air Bags. driver and front passenger, and position the front occupants Supplemental Side Air Bags for improved interaction with the Advanced Front Air Bags. Your vehicle is equipped with two types of side air bags: WARNING! • Do not drill, cut, or tamper with the knee impact bolsters in any way. • Do not mount any accessories to the knee impact bolsters such as alarm lights, stereos, citizen band radios, etc. • Supplemental Seat-Mounted Side Air Bags (SABs): Located in the outboard side of the front seats. The SABs are marked with a SRS AIRBAG label sewn into the outboard side of the seats. I nf or mat i onPr ovi dedby: 2 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the SAB deploys, it opens the seam on the outboard side of the seatback’s trim cover. The inflating SAB deploys through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure you if you are not seated properly, or if items are positioned in the area where the SAB inflates. Children are at an even greater risk of injury from a deploying air bag. WARNING! Supplemental Seat-Mounted Side Air Bag Label The SABs may help to reduce the risk of occupant injury during certain side impacts, in addition to the injury reduction potential provided by the seat belts and body structure. Do not use accessory seat covers or place objects between you and the Side Air Bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 • Supplemental Side Air Bag Inflatable Curtains SABICs may help reduce the risk of head injury to front (SABICs): Located above the side windows. The trim and rear seat outboard occupants in certain side impacts. covering the SABICs is labeled SRS AIRBAG. SABICs may reduce the risk of injuries in certain side impacts, in addition to the injury reduction potential provided by the seat belts and body structure. The SABIC deploys downward, covering the side windows. An inflating SABIC pushes the outside edge of the headliner out of the way and covers the window. The SABICs inflate with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the SABICs inflate. Children are at an even greater risk of injury from a deploying air bag. Supplemental Side Air Bag Inflatable Curtain (SABIC) Label Location The SABICs may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain side impact events. I nf or mat i onPr ovi dedby: 2 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Your vehicle is equipped with left and right Supplemental Side Air Bag Inflatable Curtains (SABICs). Do not stack luggage or other cargo up high enough to block the deployment of the SABICs. The trim covering above the side windows where the SABIC and its deployment path are located should remain free from any obstructions. • Your vehicle is equipped with SABICs. In order for the SABICs to work as intended, do not install any accessory items in your vehicle which could alter the roof. Do not add an aftermarket sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof of the vehicle for any reason. The SABICs and SABs (“Side Air Bags”) are designed to activate in certain side impacts. The Occupant Restraint Controller (“ORC”) determines whether the deployment of the Side Air Bags in a particular impact event is appropriate, based on the severity and type of collision. The side impact sensors aid the ORC in determining the appropriate response to impact events. The system is calibrated to deploy the Side Air Bags on the impact side of the vehicle during impacts that require Side Air Bag occupant protection. In side impacts, the Side Air Bags deploy independently; a left side impact deploys the left Side Air Bags only and a right-side impact deploys the right Side Air Bags only. Vehicle damage by itself is not a good indicator of whether or not Side Air Bags should have deployed. The Side Air Bags will not deploy in all side collisions, including some collisions at certain angles, or some side collisions that do not impact the area of the passenger I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 compartment. The Side Air Bags may deploy during angled or offset frontal collisions where the Advanced Front Air Bags deploy. Side Air Bags are a supplement to the seat belt restraint system. Side Air Bags deploy in less time than it takes to blink your eyes. Occupants, including children, who are up against or very close to Side Air Bags can be seriously injured or killed. Occupants, including children, should never lean on or sleep against the door, side windows, or area where the Side Air Bags inflate, even if they are in an infant or child restraint. WARNING! • Side Air Bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • Being too close to the Side Air Bags during deployment could cause you to be severely injured or killed. • Relying on the Side Air Bags alone could lead to more severe injuries in a collision. The Side Air Bags work with your seat belt to restrain you properly. In some collisions, Side Air Bags won’t deploy at all. Always wear your seat belt even though you have Side Air Bags. Seat belts (and child restraints where appropriate) are necessary for your protection in all collisions. They also help keep you in position, away from inflating Side Air Bags. To get the best protection from the Side Air Bags, NOTE: Air bag covers may not be obvious in the interior occupants must wear their seat belts properly and sit trim, but they will open during air bag deployment. upright with their backs against the seats. Children must be properly restrained in a child restraint or booster seat that is appropriate for the size of the child. I nf or mat i onPr ovi dedby: 2 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The Advanced Front Air Bags are designed to deflate immediately after deployment. NOTE: Front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision, which deploys the air bags, any or all of the following may occur: • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • The air bag material may sometimes cause abrasions Do not drive your vehicle after the air bags have deand/or skin reddening to the occupants as the air bags ployed. If you are involved in another collision, the air deploy and unfold. The abrasions are similar to fricbags will not be in place to protect you. tion rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Enhanced Accident Response System WARNING! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the seat belt retractor assemblies replaced by an authorized dealer immediately. Also, have the Occupant Restraint Controller System serviced as well. NOTE: In the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the ORC will determine whether to have the Enhanced Accident Response System perform the following functions: • Cut off fuel to the engine. • Flash hazard lights as long as the battery has power or until the ignition switch is turned to the “OFF” position. • Air bag covers may not be obvious in the interior trim, • Turn on the interior lights, which remain on as long as but they will open during air bag deployment. the battery has power or until the ignition switch is • After any collision, the vehicle should be taken to an turned to the “OFF” position. authorized dealer immediately. • Unlock the doors automatically. I nf or mat i onPr ovi dedby: 2 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ignition switch is turned to the OFF position. In order to Depending on the nature of the event the left and right move your vehicle to the side of the road, you must turn signal lights, located in the instrument panel cluster, follow the system reset procedure. may both be blinking and will continue to blink until the System Reset Procedure Customer Action 1. Turn ignition OFF. (Turn Signal Switch Must be placed in Neutral State). 2. Turn ignition ON. 3. Turn Right Turn Signal Switch ON. 4. Turn Left Turn Signal Switch ON. 5. Turn Right Turn Signal Switch ON. 6. Turn Left Turn Signal Switch ON. Customer Will See Left Turn Light is OFF. Right Turn Light BLINKS. Right Turn Light is ON SOLID. Left Turn Light BLINKS. Left Turn Light is ON SOLID. Right Turn Light BLINKS. Right Turn Light is ON SOLID. Left Turn Light BLINKS. Left Turn Light is ON SOLID. Right Turn Light is ON SOLID. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Customer Action 7. Turn Left Turn Signal Switch OFF. (Turn Signal Switch Must be placed in Neutral State). 8. Turn ignition OFF. 9. Turn Hazard Flashers OFF (Manually). Customer Will See Left Turn Light is OFF. Right Turn Light is OFF. System is now reset and the engine may be started. If a reset procedure step is not completed within 45 seconds, then the turn signal lights will turn off and the reset procedure must be performed again in order to be successful. Air Bag Warning Light The ORC monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position. If the ignition switch is in the OFF position, the air bag system is not on and the air bags will not inflate. The ORC contains a backup power supply system that The air bags must be ready to inflate for your may deploy the air bags even if the battery loses power or protection in a collision. The Occupant Re- it becomes disconnected prior to deployment. straint Controller (ORC) monitors the internal The ORC turns on the Air Bag Warning Light in the circuits and interconnecting wiring associated instrument panel for approximately four to eight seconds with air bag system electrical components. for a self-check when the ignition switch is first turned to the ON/RUN position. After the self-check, the Air Bag I nf or mat i onPr ovi dedby: 2 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Warning Light will turn off. If the ORC detects a mal- • The Air Bag Warning Light comes on intermittently or function in any part of the system, it turns on the Air Bag remains on while driving. Warning Light, either momentarily or continuously. A NOTE: If the speedometer, tachometer, or any engine single chime will sound to alert you if the light comes on related gauges are not working, the Occupant Restraint again after initial startup. Controller (ORC) may also be disabled. In this condition The ORC also includes diagnostics that will illuminate the air bags may not be ready to inflate for your protecthe instrument panel Air Bag Warning Light if a malfunc- tion. Have an authorized dealer service the air bag tion is detected that could affect the air bag system. The system immediately. diagnostics also record the nature of the malfunction. While the air bag system is designed to be maintenance WARNING! free, if any of the following occurs, have an authorized Ignoring the Air Bag Warning Light in your instrudealer service the air bag system immediately. ment panel could mean you won’t have the air bags • The Air Bag Warning Light does not come on during to protect you in a collision. If the light does not come the four to eight seconds when the ignition switch is on as a bulb check when the ignition is first turned first turned to the ON/RUN position. on, stays on after you start the vehicle, or if it comes • The Air Bag Warning Light remains on after the four to on as you drive, have an authorized dealer service the air bag system immediately. eight-second interval. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Maintaining Your Air Bag System WARNING! (Continued) WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or add aftermarket side steps or running boards. • It is dangerous to try to repair any part of the air bag system yourself. Be sure to tell anyone who works on your vehicle that it has an air bag system. • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer. Only manufacturer approved seat accessories may be used. If it is necessary to modify the air bag system for persons with disabilities, contact your authorized dealer. (Continued) I nf or mat i onPr ovi dedby: 2 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE These data can help provide a better understanding of This vehicle is equipped with an event data recorder the circumstances in which crashes and injuries occur. (EDR). The main purpose of an EDR is to record, in NOTE: EDR data are recorded by your vehicle only if a certain crash or near crash-like situations, such as an air non-trivial crash situation occurs; no data are recorded by bag deployment or hitting a road obstacle, data that will the EDR under normal driving conditions and no perassist in understanding how a vehicle’s systems per- sonal data (e.g., name, gender, age, and crash location) formed. The EDR is designed to record data related to are recorded. However, other parties, such as law envehicle dynamics and safety systems for a short period of forcement, could combine the EDR data with the type of time, typically 30 seconds or less. The EDR in this vehicle personally identifying data routinely acquired during a is designed to record such data as: crash investigation. Event Data Recorder (EDR) • How various systems in your vehicle were operating; To read data recorded by an EDR, special equipment is • Whether or not the driver and passenger safety belts required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, were buckled/fastened; such as law enforcement, that have the special equip• How far (if at all) the driver was pushing the accelera- ment, can read the information if they have access to the tor and/or brake pedal; and, vehicle or the EDR. • How fast the vehicle was traveling. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children. WARNING! (Continued) great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size. Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be prosThere are different sizes and types of restraints for ecuted for ignoring it. children from newborn size to the child almost large Children 12 years or younger should ride properly enough for an adult seat belt. Always check the child seat buckled up in a rear seat, if available. According to crash Owner’s Manual to make sure you have the correct seat statistics, children are safer when properly restrained in for your child. Carefully read and follow all the instructhe rear seats rather than in the front. tions and warnings in the child restraint Owner’s Manual and on all the labels attached to the child restraint. WARNING! In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install it in the vehicle where you will use it. (Continued) I nf or mat i onPr ovi dedby: 2 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK (732–8243). Canadian residents should refer to Transport Canada’s website for additional information: • www.tc.gc.ca/eng/roadsafety/safedriverschildsafety-index-53.htm Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Child Size, Height, Weight Or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint I nf or mat i onPr ovi dedby: Recommended Type Of Child Restraint Either an Infant Carrier or a Convertible Child Restraint, facing rearward in the rear seat of the vehicle THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight Or Age Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt Children 12 years old or younger, who have out-grown the height or weight limit of their booster seat I nf or mat i onPr ovi dedby: Recommended Type Of Child Restraint Forward-Facing Child Restraint with a five-point Harness, facing forward in the rear seat of the vehicle Belt Positioning Booster Seat and the vehicle seat belt, seated in the rear seat of the vehicle Vehicle Seat Belt, seated in the rear seat of the vehicle 2 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children should remain rear-facing until they reach the highest weight or height allowed by their convertible Safety experts recommend that children ride rear-facing child seat. in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing WARNING! child restraint. Two types of child restraints can be used rear-facing: infant carriers and convertible child seats. • Never place a rear-facing child restraint in front of Infants And Child Restraints The infant carrier is only used rear-facing in the vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrier. Convertible child seats can be used either rear-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rear-facing direction than infant carriers do, so they can be used rear-facing by children who have outgrown their infant carrier but are still less than at least two years old. an air bag. A deploying passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint. • Only use a rear-facing child restraint in a vehicle with a rear seat. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Older Children And Child Restraints Children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who are over two years old or who have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forwardfacing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forwardfacing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seatback, they should use a belt-positioning booster seat. The child and belt-positioning booster seat are held in the vehicle by the seat belt. WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • After a child restraint is installed in the vehicle, do not move the vehicle seat forward or rearward because it can loosen the child restraint attachments. Remove the child restraint before adjusting the vehicle seat position. When the vehicle seat has been adjusted, reinstall the child restraint. • When your child restraint is not in use, secure it in the vehicle with the seat belt or LATCH anchorages, or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal injury. I nf or mat i onPr ovi dedby: 2 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats 5. Can the child stay seated like this for the whole trip? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether the child can use the vehicle’s seat belt alone: If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check belt fit periodically and make sure the seat belt buckle is latched. A child’s squirming or slouching can move the seat belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly. 1. Can the child sit all the way back against the back of the vehicle seat? 2. Do the child’s knees bend comfortably over the front of the vehicle seat – while they are still sitting all the way back? 3. Does the shoulder belt cross the child’s shoulder between their neck and arm? 4. Is the lap part of the seat belt as low as possible, touching the child’s thighs and not their stomach? WARNING! Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death. A child must always wear both the lap and shoulder portions of the seat belt correctly. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Recommendations For Attaching Child Restraints Restraint Type Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Combined Weight of the Child + Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Use any attachment method shown with an “X” Below LATCH – Seat Belt Only LATCH – Seat Belt + Top Lower Anchors Lower Anchors Tether Anchor Only + Top Tether Anchor X X X X X X I nf or mat i onPr ovi dedby: 2 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors And Tethers For Children (LATCH) Restraint System has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position. These anchorages are used to install LATCH-equipped child seats without using the vehicle’s seat belts. Some seating positions may have a top tether anchorage but no lower anchorages. In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint. Please see the following table for more information. Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 LATCH Positions For Installing Child Restraints In This Vehicle 2 • • Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol I nf or mat i onPr ovi dedby: 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.5 kg) Can the LATCH anchorages and the seat belt be used together to attach a rearfacing or forward-facing child restraint? Can two child restraints be attached using a common lower LATCH anchorage? No No I nf or mat i onPr ovi dedby: Use the LATCH anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and tether anchor instead of the LATCH system once the combined weight is more than 65 lbs (29.5 kg). Do not use the seat belt when you use the LATCH anchorage system to attach a rearfacing or forward-facing child restraint. Never “share” a LATCH anchorage with two or more child restraints. If the center position does not have dedicated LATCH lower anchorages, use the seat belt to install a child seat in the center position next to a child seat using the LATCH anchorages in an outboard position. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Can the rear-facing child restraint touch the back of the front passenger seat? Can the head restraints be removed? Yes Yes The child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information. Yes, all may be removed Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion. LATCH Anchorages I nf or mat i onPr ovi dedby: 2 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The Upper Tether Anchorages Center Seat LATCH There are tether strap anchorages behind each rear seating position located on the back of the seat. WARNING! This vehicle does not have a center seating position. Do not use the center lower LATCH anchorages to install a child seat in the center of the back seat. LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will Always follow the directions of the child restraint manuhave a hook or connector to attach to the lower anchorage facturer when installing your child restraint. Not all child and a way to tighten the connection to the anchorage. restraint systems will be installed as described here. Forward-facing child restraints and some rear-facing child restraints will also be equipped with a tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seatIf the selected seating position has a Switchable Autoing position. matic Locking Retractor (ALR) seat belt, stow the seat belt, following the instructions below. See the section 4. If the child restraint has a tether strap, connect it to the “Installing Child Restraints Using the Vehicle Seat Belt” top tether anchorage. See the section “Installing Child to check what type of seat belt each seating position has. Restraints Using the Top Tether Anchorage” for directions to attach a tether anchor. 1. Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more 5. Tighten all of the straps as you push the child restraint easily attach the hooks or connectors to the vehicle rearward and downward into the seat. Remove slack anchorages. in the straps according to the child restraint manufacturer’s instructions. 2. Place the child seat between the lower anchorages for that seating position. For some second row seats, you 6. Test that the child restraint is installed tightly by may need to recline the seat and/or raise the head pulling back and forth on the child seat at the belt restraint to get a better fit. If the rear seat can be moved path. It should not move more than 1 inch (25.4 mm) forward and rearward in the vehicle, you may wish to in any direction. move it to its rear-most position to make room for the child seat. You may also move the front seat forward to allow more room for the child seat. To Install A LATCH-Compatible Child Restraint I nf or mat i onPr ovi dedby: 2 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Stow An Unused ALR Seat Belt: When using the LATCH attaching system to install a child restraint, stow all ALR seat belts that are not being used by other occupants or being used to secure child restraints. An unused belt could injure a child if they play with it and accidentally lock the seat belt retractor. Before installing a child restraint using the LATCH system, buckle the seat belt behind the child restraint and out of the child’s reach. If the buckled seat belt interferes with the child restraint installation, instead of buckling it behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. Do not lock the seat belt. Remind all children in the vehicle that the seat belts are not toys and that they should not play with them. WARNING! • Improper installation of a child restraint to the LATCH anchorages can lead to failure of the restraint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • Child restraint anchorages are designed to withstand only those loads imposed by correctly-fitted child restraints. Under no circumstances are they to be used for adult seat belts, harnesses, or for attaching other items or equipment to the vehicle. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Installing Child Restraints Using The Vehicle Seat Belt Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip. The ALR retractor can be “switched” into a locked mode by pulling all of the webbing out of the retractor and then letting the webbing retract back into the retractor. If it is locked, the ALR will make a clicking noise while the webbing is pulled back into the retractor. For additional information on ALR, refer to the “Automatic Locking Mode” description under “Occupant Restraints.” 2 • ALR = Switchable Automatic Locking Retractor • I nf or mat i onPr ovi dedby: Top Tether Anchorage Symbol 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? Yes No Yes I nf or mat i onPr ovi dedby: Always use the tether anchor when using the seat belt to install a forward facing child restraint, up to the recommended weight limit of the child restraint. Contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact. Yes, all may be removed Do not twist the buckle stalk in a seating position with an ALR retractor. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 5. To lock the seat belt, pull down on the shoulder part of the seat belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing Place the child seat in the center of the seating to retract back into the retractor. As the webbing position. For some second row seats, you may need to retracts, you will hear a clicking sound. This means the recline the seat and/or raise the head restraint to get a seat belt is now in the Automatic Locking mode. better fit. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move it to its 6. Try to pull the webbing out of the retractor. If it is locked, you should not be able to pull out any webrear-most position to make room for the child seat. bing. If the retractor is not locked, repeat step 5. You may also move the front seat forward to allow more room for the child seat. 7. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the Pull enough of the seat belt webbing from the retractor to child restraint rearward and downward into the vehicle pass it through the seat belt path of the child restraint. Do seat. not twist the belt webbing in the belt path. Slide the latch plate into the buckle until you hear a 8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the “click.” tether strap to the anchorage and tighten the tether strap. See the section “Installing Child Restraints Using Pull on the webbing to make the lap portion tight the Top Tether Anchorage” for directions to attach a against the child seat. tether anchor. Installing A Child Restraint With A Switchable Automatic Locking Retractor (ALR) 1. 2. 3. 4. I nf or mat i onPr ovi dedby: 2 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the seat belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the seat belt occasionally, and pull it tight if necessary. WARNING! (Continued) and Tethers for CHildren (LATCH) Restraint System” for the location of approved tether anchorages in your vehicle. Installing Child Restraints Using The Top Tether Anchorage WARNING! Do not attach a tether strap for a rear-facing car seat to any location in front of the car seat, including the seat frame or a tether anchorage. Only attach the tether strap of a rear-facing car seat to the tether anchorage that is approved for that seating position, located behind the top of the vehicle seat. See the section “Lower Anchors (Continued) 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 2 3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. Rear Seat Tether Strap Mounting 4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. I nf or mat i onPr ovi dedby: 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. Transporting Pets Air Bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or could injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to “Maintenance Procedures” in “Maintaining Your Vehicle.” I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 CAUTION! WARNING! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. I nf or mat i onPr ovi dedby: 2 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! (Continued) WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. • If you are required to drive with the trunk/liftgate/ rear doors open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. (Continued) • If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Safety Checks You Should Make Inside The Vehicle Seat Belts not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Inspect the seat belt system periodically, checking for cuts, Defroster frays, and loose parts. Damaged parts must be replaced Check operation by selecting the defrost mode and place immediately. Do not disassemble or modify the system. the blower control on high speed. You should be able to feel the air directed against the windshield. See your Front seat belt assemblies must be replaced after a authorized dealer for service if your defroster is inopercollision. Rear seat belt assemblies must be replaced after able. a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). If there is any question regarding seat Floor Mat Safety Information belt or retractor condition, replace the seat belt. Always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals The light should come on and remain on for or impair safe operation of your vehicle in other ways. four to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is Air Bag Warning Light I nf or mat i onPr ovi dedby: 2 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle. • Never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals. • Check mounting of mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning. • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory. Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle. (Continued) I nf or mat i onPr ovi dedby: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel bolts for tightness. Check the tires (including spare) for proper cold inflation pressure. Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid (if equipped), or brake fluid leaks are suspected. The cause should be located and corrected immediately. Check for positive closing, latching, and locking. Lights Have someone observe the operation of brake lights and exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. I nf or mat i onPr ovi dedby: 2 I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ! POWER CONVERTIBLE TOP — IF EQUIPPED . .84 ▫ Heated Mirrors — If Equipped . . . . . . . . . . . .90 ▫ Lowering The Power Top. . . . . . . . . . . . . . . . .84 ▫ Sun Visors . . . . . . . . . . . . . . . . . . . . . . . . . . .91 ▫ Raising The Power Top . . . . . . . . . . . . . . . . . .84 ! BLUE&ME™ HANDS-FREE COMMUNICATION. . . . . . . . . . . . . . . . . . . . . .91 ▫ Power Convertible Top Relearn Procedure . . . . .86 ▫ Blue&Me™ Hands-Free Communication ▫ Wind Stop . . . . . . . . . . . . . . . . . . . . . . . . . . .87 Overview — If Equipped . . . . . . . . . . . . . . . . .91 ! MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 ▫ The Hands-Free Kit . . . . . . . . . . . . . . . . . . . . .92 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .87 ! SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 ▫ Automatic Dimming Mirror — If Equipped . . .88 ▫ Forward/Rearward Adjustment . . . . . . . . . . . .99 ▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . . .89 ▫ Recline Adjustment . . . . . . . . . . . . . . . . . . . .100 ▫ Folding Mirrors. . . . . . . . . . . . . . . . . . . . . . . .90 I nf or mat i onPr ovi dedby: 3 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Seat Height Adjustment . . . . . . . . . . . . . . . . .101 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . .110 ▫ EZ Entry Feature . . . . . . . . . . . . . . . . . . . . . .101 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . . .111 ▫ Memory Feature . . . . . . . . . . . . . . . . . . . . . .102 ▫ Follow Me Home/Headlight Delay . . . . . . . . .111 ▫ Heated Seats — If Equipped . . . . . . . . . . . . .103 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . .111 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . .104 ▫ Front Fog Lights — If Equipped . . . . . . . . . . .113 ! TO OPEN AND CLOSE THE HOOD . . . . . . . . .106 ! WINDSHIELD WIPERS AND WASHERS . . . . . .113 ! LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 ▫ Front Windshield Wiper Operation . . . . . . . . .114 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . . .108 ▫ Rear Windshield Wiper . . . . . . . . . . . . . . . . .116 ▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . .108 ! TILT STEERING COLUMN — IF EQUIPPED . . .117 ▫ High Beams . . . . . . . . . . . . . . . . . . . . . . . . .109 ! ELECTRONIC SPEED CONTROL . . . . . . . . . . .118 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . .109 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . .119 ▫ Parking Lights . . . . . . . . . . . . . . . . . . . . . . .109 ▫ To Set A Desired Speed . . . . . . . . . . . . . . . . .119 ▫ Daytime Running Lights — If Equipped . . . . .110 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . .120 I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . .120 ▫ To Close . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . .120 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . .130 ▫ To Accelerate For Passing . . . . . . . . . . . . . . . .121 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .130 ! REAR PARK ASSIST — IF EQUIPPED . . . . . . . .122 ▫ Emergency Operation. . . . . . . . . . . . . . . . . . .130 ▫ Rear Park Assist Sensors . . . . . . . . . . . . . . . .122 ▫ Sun Shade — If Equipped . . . . . . . . . . . . . . .130 ▫ Rear Park Assist Warning Display . . . . . . . . . .123 ! ELECTRICAL POWER OUTLETS . . . . . . . . . . .131 ▫ Rear Park Assist Display . . . . . . . . . . . . . . . .123 ! CIGAR LIGHTER — IF EQUIPPED . . . . . . . . . .134 ▫ Rear Park Assist Audible Alerts . . . . . . . . . . .124 ! CUPHOLDERS . . . . . . . . . . . . . . . . . . . . . . . .134 ▫ Failure Indications . . . . . . . . . . . . . . . . . . . . .125 ! STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .135 ▫ Cleaning The Rear Park Assist System . . . . . . .126 ▫ Glove Compartment . . . . . . . . . . . . . . . . . . .135 ▫ Park Assist System Usage Precautions . . . . . . .126 ! CARGO AREA FEATURES . . . . . . . . . . . . . . . .136 ! POWER SUNROOF — IF EQUIPPED . . . . . . . .128 ! REAR WINDOW FEATURES . . . . . . . . . . . . . .137 ▫ To Open . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . .137 I nf or mat i onPr ovi dedby: 3 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The power top buttons will operate when the On vehicles equipped with a power convertible top, the ignition switch is turned to the ACC/ON/RUN position. power convertible top switch is located on the overhead Lowering The Power Top console. The switch contains two buttons. The passenger Press the top open button approximately one second for side button, is used to open the power top, and the driver the three-quarter open position. Press the top open side button, is used to close the power top. button for approximately one second a second time to fully open the convertible top. POWER CONVERTIBLE TOP — IF EQUIPPED Raising The Power Top From the convertible top fully open position, press the top close button for approximately one second for the three-quarter open position. Press the top close button for approximately one second a second time for the onequarter open position. Press and hold close button to fully close convertible top. Power Convertible Top Switch I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 NOTE: Rail lubrication is recommended every 2000 cycles, or if scratching noises due to dust are present. Refer to “Fluids, Lubes, and Genuine Part” in “Maintaining Your Vehicle” for information. CAUTION! (Continued) • Use care when washing the vehicle, water pressure directed at the weather strip seals may cause water to leak into the vehicle’s interior. CAUTION! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • Avoid high-pressure car washes, as they can damage the top material. Also, increased water pressure may force water past the weather strips. • Remove any standing water from the top and dry the surface before opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be expected to prevent the ejection of the occupants in a collision. Therefore, it is important that all occupants wear their seat belts at all times. Death or serious injuries could occur if you are ejected from the vehicle during a collision. (Continued) I nf or mat i onPr ovi dedby: 3 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Convertible Top Relearn Procedure 6. Hold the CLOSED button to move the top to the fully closed position. If your power convertible top does not operate in the Auto Opening/Closing mode (automatically opening/ 7. CONTINUE to hold the CLOSED button until the top closing to the one-quarter open and three-quarter open begins to cycle fully open, then release the CLOSED comfort stops), or if the trunk lid does not open - the button. following relearn procedure may be necessary. At the end of step 7 the top will automatically cycle to the 1. Confirm that the door/trunk lid are closed. fully open position, and then close to the 1/4 open position. 2. Begin with the top in the fully closed position (using This will confirm that the relearn procedure was successful. manual mode). 3. Hold the OPEN button to move the top to the fully Auto Open/Close will now be functional. Trunk lid operation will be functional. open position. 4. CONTINUE to hold the OPEN button for an addi- NOTE: DO NOT interrupt this activity. tional three seconds. If the power convertible top does not relearn repeat the procedure a second time. 5. Release the OPEN button. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Wind Stop The Wind Stop installs in the backseat area of the vehicle. The Wind Stop will not interfere with power top operation. Therefore, it can remain installed when the top is up. 3 MIRRORS Inside Day/Night Mirror The mirror can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield). I nf or mat i onPr ovi dedby: Adjusting Rearview Mirror 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. NOTE: This feature is disabled when the vehicle is moving in reverse. Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 The power mirror controls consist of a mirror select The power mirror controls are located on the driver’s switch and a four-way mirror control switch. To adjust a mirror, press the mirror select switch to either the L (left) door trim panel. or R (right) to select the mirror you need to adjust. Power Mirrors Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. WARNING! Power Mirror Switches Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. I nf or mat i onPr ovi dedby: 3 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Spotter Mirror — If Equipped Folding Mirrors Some models are equipped with a driver’s side spotter The exterior mirrors are hinged to allow the mirror to mirror. The spotter mirror allows for a greater range of pivot forward or rearward to help avoid damage. The visibility on the driver’s side of the vehicle. mirror has three detent positions: full forward, normal and full rearward. Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped). Refer to “Rear Window Features” in “Understanding The Features Of Your Vehicle” for further information. Spotter Mirror I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Sun Visors BLUE&ME™ HANDS-FREE COMMUNICATION The driver and passenger sun visors are located on the Blue&Me™ Hands-Free Communication headliner, near the front windshield. The sun visor can be Overview — If Equipped rotated downward or up against the door glass. Both sun Windows Mobile™-based FIAT BLUE&ME™ is a pervisors are equipped with courtesy mirrors. sonal telematic system enabling you to use communication and entertainment applications expressly designed for use in the car. The BLUE&ME™ system installed on your car is equipped with a hands-free kit, message reader and media player, and it is preset for future installation of additional services. Sun Visor (Passenger Side Shown) The BLUE&ME™ system, fully integrated with voice commands, buttons on the steering wheel and multifunction display messages, gives you the possibility of interacting with your Bluetooth® wireless technology mobile phone (even if you keep it in your pocket or bag) without I nf or mat i onPr ovi dedby: 3 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE having to take your eyes off the road or remove your hands from the steering wheel. To use voice commands you are not required to train the voice recognition system to recognize your voice. This implies that the system is nearly equally performing with different persons, i.e.: the voice recognition system is of the “speaker independent” type. The Hands-Free Kit The basic characteristic of this hands-free kit is voice recognition with Bluetooth® wireless technology. With this system you can make and receive calls safely and securely by using either voice commands or buttons on the steering wheel. This can be done under any driving condition without ever having to take your eyes off the With this system you can also play your favorite music road or remove your hands from the steering wheel, as stored on USB device and select tracks and playback required by current laws. modes with both voice commands or buttons on the Bluetooth® wireless technology enables wireless connecsteering wheel. tion between your mobile phone and the hands-free kit This device complies with Part 15 of the FCC rules installed on your car. subject to the following two conditions: To use the hands-free kit, you need a Bluetooth® wireless technology enabled mobile phone. This hands-free kit • This device may not cause harmful interference. gives you the possibility of interacting vocally with your • This device must accept all interference received, in- mobile phone while driving, even if your mobile device cluding interference that may cause undesired opera- does not feature Voice Recognition. You can also interact tion. with your mobile phone manually and visually using the I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 steering wheel controls and the instrument panel multi- To get started with BLUE&ME™ hands-free kit with voice function display. Please refer to the Fiat Blue & Me Radio recognition, you have to simply pair your Bluetooth® wireSupplement for further information. less technology enabled mobile phone with the system. Pairing is an operation that has to be made only once. NOTE: • During the mobile phone pairing procedure, BLUE&ME™ attempts to detect a phone equipped with Bluetooth® wireless technology within range and then establishes the connection using a Personal Identification Number (PIN). Steering Wheel Hands Free Buttons 1 — Mute/ESC 2 — Phone/Main 3 — Phone Hang Up 4 — Voice Recognition (VR) • Once your phone is paired, you have the option to transfer your mobile phone contacts to the hands-free kit, to make a phone call either by using the contacts list or directly pronouncing the phone number, to answer a call and also to answer another incoming phone call. I nf or mat i onPr ovi dedby: 3 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To interact with BLUE&ME™ you can use either the The hands-free kit enables the following operations: buttons on the steering wheel or voice commands. • Contact Calling By Voice — You can call a contact in With voice recognition, you can perform system funcyour mobile phone phonebook using your voice. You tions by speaking voice commands, also identified as can also call a contact in your phonebook by scanning “keywords”. When the system recognizes a keyword, through the entries on the multifunction display. (To it will respond with the appropriate action. Voice use this option you have to transfer your mobile phone recognition is an easy and convenient way to use contacts to the hands-free kit phonebook). BLUE&ME™. • Digit Dialing By Voice — You can dial a phone All the system functions are available within the number by pushing the VR button on the steering BLUE&ME™ Main Menu. When the car is not moving, wheel and speaking the digits to be dialed. you can scroll through the complete menu by using either the buttons on the steering wheel or the voice commands. • To Call The SMS Text Sender — Call directly the last When you are traveling, you can interact with SMS text sender or the sender of a message received BLUE&ME™ by using the buttons on the steering wheel and stored in the BLUE&ME™ inbox. or voice commands relevant only to phone functions (LAST CALLS and PHONEBOOK) and the media player. • To Answer A Call — You can answer an incoming call by pushing the MAIN/Phone button on the steering To activate settings when travelling you can only use wheel. voice commands. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • Conference Call — You can call another contact while After pairing and connecting your phone with the you are engaged in a phone conversation (with BLUE&ME™ system, you can make phone calls by Bluetooth® phones supporting this option). speaking keywords or pushing buttons on the steering wheel. When using the hands-free phone, the audio • Call Waiting — While engaged in a phone conversaoutput of a phone conversation is heard through your car tion, you can receive notification of another incoming sound speakers. phone call, answer the other incoming phone call, and switch between two ongoing phone conversations. Message Reader (Call waiting is only supported by a subset of compat- The BLUE&ME™ message reader enables automatic ible mobile phones). reading, through the car sound system, of the SMS texts • Refusing Incoming Call Or Ending A Call — You can refuse an incoming call or end a current call by pushing the Phone Hang-up button on the steering wheel. you receive on your Bluetooth® wireless technology mobile phone that are received when the phone is paired and connected to the BLUE&ME™ system. It does not provide access to messages that were received before the device was connected with the BLUE&ME™ system. The message reader will also interpret many abbreviations and emoticons contained in the SMS text. I nf or mat i onPr ovi dedby: 3 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Not all mobile phones support the SMS text message • To manage the list of SMS texts received on your BLUE&ME™ paired mobile phone. reader function or automatic phonebook transfer via Bluetooth®. For further information on the list of compatible • To read the messages received and stored. Messages mobile phones go to http://www.fiatusa.com, find the can be read multiple times. SUPPORT section near the bottom of web page and • To call the SMS text sender using the buttons on the click on the Bluetooth® logo. steering wheel or voice commands. Message reader functions are managed by the control buttons on the steering wheel or by the BLUE&ME™ • To delete individual messages or the entire inbox using the buttons on the steering wheel or voice commands. voice commands. The BLUE&ME™ message reader enables the following The BLUE&ME™ system can also recognize and read operations: abbreviations, if any (e.g. “ILUVU” will be read like “I love you”) and interpret the most usual emoticons • To display an indicator on the instrument panel that (e.g. :-) will be read like “Smile”), that are currently used indicates you have received a new SMS text. It will to write SMS texts. display the sender’s number/name and will ask you whether to read the text of the message to you. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 • Audio File Selection By Category — You can play all audio files of a certain category, e.g.: album, artist or With the BLUE&ME™ media player you can play the genre. digital audio files stored on a USB device by simply connecting it to the USB port located in the center console • Playback Options — While playing tracks you can of the car. A second USB port, used for charging only, is select the following options: Play, Stop, Next track, located in the glovebox. Previous track, Shuffle and Loop track. Media Player In this way, while you are driving you can play your NOTE: favorite music collections. • The media player does not support audio files com• iPod® Player — See dedicated paragraph under Mepressed with other formats and DRM (Digital Rights dia Player Functions. Management) protected audio files. Non-supported audio files that may be present on the USB device will The media player enables the following operations: be ignored. • Digital Audio Playback — You can play all your digital audio files (.mp3, .wma, .wav, .aac) or play a customized playlist (.m3u or .wpl format). I nf or mat i onPr ovi dedby: 3 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To use the media player, you have to simply connect (directly or by an extension lead) your USB device to the center console USB port. After turning the ignition key to ON, BLUE&ME™ will start building your media library. At the end of this operation you can surf the complete library and scroll its categories as required using the buttons on the steering wheel or voice commands. BLUE&ME™ will then play your selection via the car sound system. WARNING! • Driving while distracted can result in loss of vehicle control, accident and injury. It is strongly recommended that you use extreme caution when using any device or feature that may take your focus off the road or your hands off the steering wheel. Your primary responsibility is the safe operation of your vehicle. WARNING! (Continued) • The use of any handheld device while driving is not recommended. Use voice-operated systems when possible. Follow all applicable laws that may affect the use of electronic devices while driving. • Keep the Owner’s Manual in the car: when kept in the car, the Owner’s Manual will be available for you and other users unfamiliar with the system. Please make certain that before using the system for the first time, all persons have access to the Owner’s Manual and read its instructions and safety information carefully. (Continued) I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 SEATS Forward/Rearward Adjustment Seats are a part of the Occupant Restraint System of the The adjusting bar is located at the front of the seats, near vehicle. the floor. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. I nf or mat i onPr ovi dedby: 3 Adjusting Bar 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired position is reached. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Recline Adjustment The recline adjustment lever is located on the inboard side of the seat. To recline the seatback, lift up the recline lever, lean back until the desired position has been reached, and release the lever. WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. Recline Lever I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. 3 Seat Height Adjustment The driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pump the lever upward to raise the seat height, or pump the lever downward to lower the seat height. Height Adjuster EZ Entry Feature The driver and front passenger seats have an EZ entry feature for rear seat passengers. Pull forward on the release lever, located on the outboard side of the seatback, dump the seatback forward, then slide the seat forward to allow access in and out of the rear seat. I nf or mat i onPr ovi dedby: 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memory Feature Both front seats have a memory feature, which can operate in two ways: Memory Function Option 1 — Full Seat Back And Track Fore/Aft Position Memory: After using the EZ entry function, the seatback angle and the Track fore/aft adjuster can both re-lock into the position they were most recently adjusted to. This is accomplished if the seat is moved fully rearward to its last fore/aft position on the tracks before the seat back is returned upright. EZ Entry Lever Lift the seatback upright and push the seat rearward to its locked position once the rear passengers are seated. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Press the switch once to turn on the heated seats. Press the switch a second time to shut the heating elements off. Memory Function Option 2 — Seat Back Only Memory: After using the EZ entry function, the seat back may first be returned upright prior to going back to the last NOTE: Once a heat setting is selected, heat will be felt fore/aft (memory) position on the tracks. This results in within two to five minutes. the seat back memory being set only – The track will then be locked forward of its last set fore/aft memory posiWARNING! tion. To then reset the fore/aft track memory feature (to reestablish Memory Function Option 1), the seat has to be • Persons who are unable to feel pain to the skin returned fully rearward to its last fore/aft memory track because of advanced age, chronic illness, diabetes, position as described in Memory Function Option 1. spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care Heated Seats — If Equipped when using the seat heater. It may cause burns On some models, the front driver and passenger seats even at low temperatures, especially if used for may be equipped with heaters in both the seat cushions long periods of time. and seatbacks. The controls for the front heated seats are located on the center instrument panel area. (Continued) I nf or mat i onPr ovi dedby: 3 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) WARNING! • Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision. Head Restraints Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rearimpact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Reactive Head Restraints — Front Seats The front driver and passenger seats are equipped with Reactive Head Restraints. In the event of a rear impact the Reactive Head Restraints will automatically extend forward minimizing the gap between the back of the occupant’s head and the Reactive Head Restraint. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. The Reactive Head Restraints will automatically return to their normal position following a rear impact. If the Reactive Head Restraints do not return to their normal position, see your authorized dealership immediately. NOTE: The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealership. WARNING! Push Button Do not place items over the top of the Reactive Head Restraint, such as coats, seat covers or portable DVD players. These items may interfere with the operation of the Reactive Head Restraint in the event of a collision and could result in serious injury or death. I nf or mat i onPr ovi dedby: 3 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Head Restraints TO OPEN AND CLOSE THE HOOD To raise the head restraint, pull upward on the head re- To open the hood, two latches must be released. straint. To lower the head restraint, press the push button, located at the base of the head restraint, and push down- 1. Pull the bottom of the RED hood release lever, located on the left kick panel, rearward. ward on the head restraint. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for information on tether routing. Hood Release Lever Push Button I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 2. Rotate the safety catch under the front edge of the hood, near the center, and raise the hood. 3 Hood Prop Rod In hot climates, the prop rod may be hot. Pick up the prop rod at the foam on the end of the prop rod. Hood Safety Latch Location 3. Lift the hood prop rod that clips to the right side (left side when standing in front of the hood) of the engine compartment. Place the hood prop rod in the hole of hood hinge to secure the hood in the open position. I nf or mat i onPr ovi dedby: 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! Multifunction Lever The multifunction lever, located on the left side of the steering wheel, controls the operation of the headlights, headlight beam selection, passing light and turn signals. NOTE: The external lights can only be turned on with the ignition in the ON/RUN position. Headlights Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. I nf or mat i onPr ovi dedby: Rotate the end of the multifunction lever upward to the first detent for headlight operation. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 High Beams With the low beams activated, push the multifunction lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. Flash-To-Pass Headlight Operation You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to turn on until the lever is released. NOTE: When the headlights are turned on, the Daytime Parking Lights Running Lights will be deactivated. To turn on the parking lights, remove the key or turn the ignition to OFF/LOCK position and turn on the headlights. I nf or mat i onPr ovi dedby: 3 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights — If Equipped To activate the Daytime Running Lights (DRL), rotate the end of the multifunction lever to the O symbol. NOTE: The low beams and side/taillights will not be on with DRL. If allowed by law in the country in which the vehicle was purchased the DRL function can be turned on or off using the display menus. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. Turn Signal Operation Turn Signals Push the multifunction lever upward to signal a right NOTE: The indicators will automatically turn off when turn or downward to signal a left turn. The correspond- the turn has been completed and the steering wheel is ing indicator in the instrument cluster will blink to returned to a straight position. indicate the operation of the turn signal. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Deactivation Lane Change Assist Tap the lever up or down once, without moving beyond Pull the multifunction lever toward the steering wheel the detent, and the turn signal (right or left) will flash and hold it for more than two seconds. three times then automatically turn off. Interior Lights Follow Me Home/Headlight Delay The interior light switches are located in the overhead conWhen this feature is selected the driver can choose to sole. The interior lights can be set to three different positions have the headlights remain on for a preset period of time. (Off/Left Position, Center Position, On/Right Position). Activation Remove the key or turn the ignition to the OFF/LOCK position, and pull the multifunction lever toward the steering wheel, within two minutes. Each time the lever is pulled, the activation of the lights will be extended by 30 seconds. The activation of the lights can be extended to a maximum of 210 seconds. Using the switch on the left overhead, press the switch to the right from its center position and the lights are always on. Press the switch to the left from its center position and the lights are always off. Leave the switch in the center position, and the lights are turned on and off when the doors are opened or closed. The switch on the right side of the overhead console controls the map or reading function of the lights. Press the switch to the right to turn on the right light and press the switch to the left to turn on the left light. I nf or mat i onPr ovi dedby: 3 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • When the doors are unlocked with the Key Fob a 10 second timer is activated. Before getting out of the vehicle be sure that the switch is in the center position or that the lights are off to avoid draining the battery. • When the doors are locked with the Key Fob the lights will turn off. Interior Light Timing (Center Position) There are four different modes of operation that can be activated in this position: Interior Light Timing (On/Right Position) • When all doors are closed a 15 minute timer is activated. NOTE: The timer is deactivated when the key is moved • When one door is opened a three minute timer is into the ON/RUN position. activated. • When the key is removed from the ignition (within two minutes of the ignition being turned off), a 10 second timer is activated. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Press the switch once to turn the front fog lights on. Press The fog light switch is located on the center stack of the the switch a second time to turn the front fog lights off. instrument panel, just below the radio. WINDSHIELD WIPERS AND WASHERS Front Fog Lights — If Equipped The windshield wiper/washer lever is located on the right side of the steering column. NOTE: The windshield wipers/washers will only operate with the ignition in the ON/RUN position. Fog Light Switch I nf or mat i onPr ovi dedby: 3 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Windshield Wiper Operation Windshield Wiper Off There are five different modes of operation for the front This is the normal position of the wiper lever. windshield wipers. The windshield wiper lever can be Intermittent Wiper Operation raised or lowered to access these modes: Push the lever downward to the first detent. The wipers will operate intermittently. NOTE: The Intermittent function only has one detent but wiper delay will vary with changes in vehicle speed. As vehicle speed increases the delay time will decrease. Low Speed Push the lever downward to the second detent. The wipers will operate at low speed. High Speed Windshield Wiper Operation Push the lever downward to the third detent. The wipers will operate at high speed. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Manual High Speed/Mist Push the lever upward from the off position. The wipers will operate at high speed to clear off road mist or spray from a passing vehicle. This operation will continue until the lever is released. When the lever is released, the wipers will return to the off position and automatically shut off. Front Windshield Washer Operation Pull the windshield wiper/washer lever toward the steering wheel to activate the washers. The wipers will activate automatically for three cycles after the lever is released. CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • In cold weather, always turn off the wiper switch and allow the wipers to return to the “Park” position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. • Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. I nf or mat i onPr ovi dedby: 3 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Windshield Wiper Rotate the end of the windshield wiper/washer lever upward to the first detent past the intermittent settings for intermittent wipe operation. With the front windshield wiper active, rotate the end of the windshield wiper/washer lever upward. The rear wiper will operate in the same mode as the front windshield wipers, but at half the frequency. When the transmission is shifted into REVERSE, the rear wiper will automatically operate at Low Speed and return to normal operation when the transmission is shifted out of REVERSE. Rear Wiper Operation NOTE: The windshield wipers/washers will only operate with the ignition in the ON/RUN position. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Rear Windshield Washer Operation Push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released. 3 TILT STEERING COLUMN — IF EQUIPPED This feature allows you to tilt the steering column upward or downward. The tilt control lever is located on the left-side of the steering column, below the turn signal controls. Tilt Control Lever Push down on the lever to unlock the column. With one hand firmly on the steering wheel, move the steering column up or down as desired. Push the lever up to lock the column firmly in place. I nf or mat i onPr ovi dedby: 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. ELECTRONIC SPEED CONTROL When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The Electronic Speed Control buttons are located on the right side of the steering wheel. I nf or mat i onPr ovi dedby: Electronic Speed Control Buttons UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 NOTE: In order to ensure proper operation, the Electronic Speed Control system has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control system can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Activate To Set A Desired Speed Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate. To turn the system off, push the ON/OFF button a second time. The Cruise Indicator Light will turn off. The system should be turned off when not in use. Turn the Electronic Speed Control ON. When the vehicle has reached the desired speed, press the SET (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET (-) button. I nf or mat i onPr ovi dedby: 3 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “ UnderA soft tap on the brake pedal, pushing the CANC button, standing Your Instrument Panel” for more information. or normal brake pressure while slowing the vehicle will The speed increment shown is dependent on the selected deactivate Electronic Speed Control without erasing the speed unit of U.S. (mph) or Metric (km/h): set speed memory. Pressing the ON/OFF button or turning the ignition switch OFF erases the set speed in U.S. Speed (mph) memory. • Pressing the RES (+) button once will result in a 1 mph To Resume Speed increase in set speed. Each subsequent tap of the button results in an increase of 1 mph. To resume a previously set speed, push the RES (+) To Deactivate button and release. Resume can be used at any speed • If the button is continually pressed, the set speed will above 25 mph (40 km/h). continue to increase until the button is released, then the new set speed will be established. To Vary The Speed Setting To Increase Speed Metric Speed (km/h) When the Electronic Speed Control is set, you can in- • Pressing the RES (+) button once will result in a 1 km/h increase in set speed. Each subsequent tap of crease speed by pushing the RES (+) button. the button results in an increase of 1 km/h. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 • If the button is continually pressed, the set speed will • If the button is continually pressed, the set speed will continue to increase until the button is released, then continue to decrease until the button is released, then the new set speed will be established. the new set speed will be established. To Decrease Speed Metric Speed (km/h) When the Electronic Speed Control is set, you can de- • Pressing the SET (-) button once will result in a 1 km/h crease speed by pushing the SET (-) button. decrease in set speed. Each subsequent tap of the button results in a decrease of 1 km/h. The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “ Under- • If the button is continually pressed, the set speed will standing Your Instrument Panel” for more information. continue to decrease until the button is released, then The speed decrement shown is dependant on the selected the new set speed will be established. speed unit of U.S. (mph) or Metric (km/h): To Accelerate For Passing U.S. Speed (mph) Press the accelerator as you would normally. When the • Pressing the SET (-) button once will result in a 1 mph pedal is released, the vehicle will return to the set speed. decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph. I nf or mat i onPr ovi dedby: 3 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using Electronic Speed Control On Hills REAR PARK ASSIST — IF EQUIPPED The transmission may downshift on hills to maintain the The Rear Park Assist system provides visual and audible vehicle set speed. indications of the distance between the rear fascia/ bumper and a detected obstacle when backing up, e.g. NOTE: The Electronic Speed Control system maintains during a parking maneuver. Refer to the “Park Assist speed up and down hills. A slight speed change on System Usage Precautions” for the limitations of this moderate hills is normal. system and recommendations. On steep hills, a greater speed loss or gain may occur so The Rear Park Assist is automatically activated when the it may be preferable to drive without Electronic Speed transmission is placed into REVERSE. Control. Rear Park Assist Sensors WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery. The four Rear Park Assist sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles, in the horizontal direction, from approximately 12 in (30 cm) up to 55 in (140 cm) from the center of the rear fascia/bumper and up to 24 in (60 cm) from the corners of the rear fascia/bumper, depending on the location, type and orientation of the obstacle. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 If several obstacles are detected, the Rear Park Assist Rear Park Assist Display system indicates the nearest obstacle. When the vehicle is in REVERSE, the warning display The minimum height of a detectable obstacle corresponds will turn ON indicating the system status. to the maximum height of an obstacle that would clear the The system will indicate a detected obstacle by showing underside of the car during the parking maneuver. arcs in one or more regions based on the obstacle’s distance and location relative to the vehicle. Rear Park Assist Warning Display The Rear Park Assist Warning screen is located within the Electronic Vehicle Information Center (EVIC). It provides audible and visual warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. Refer to #Electronic Vehicle Information Center (EVIC)# in “Understanding Your Instrument Panel# for further information. If an obstacle is detected in the center rear region, the display will show solid arcs in the center rear region and will produce an audible alert. As the vehicle moves closer to the obstacle, the display will show fewer arcs and the audible alert becomes more frequent. If an obstacle is detected in the left and/or right rear region, the display will show solid arcs in the left and/or right rear region and will produce an audible alert. As the vehicle moves closer to the obstacle, the display will show fewer arcs and the audible alert becomes more frequent. I nf or mat i onPr ovi dedby: 3 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE between the tones are directly proportional to the disIf an obstacle is behind the vehicle when the transmission tance from the obstacle. Pulses emitted in quick succession indicate the presence of a very close obstacle. A is placed into REVERSE, an audible alert is activated. continuous tone indicates that the obstacle is less than 12 The tones emitted by the loudspeaker inform the driver in (30 cm) away. that the vehicle is approaching an obstacle. The pauses Audible And Visual Signals Supplied By The Rear Park Assist System Rear Park Assist Audible Alerts SIGNAL Obstacle Distance MEANING An obstacle is present within the sensors’ field of view INDICATION Audible signal (dashboard loudspeaker) • Sound pulses emitted at a rate that increases as the distance decreases. • Emits continuous tone at 12 in (30 cm). • Adjustable volume level. (Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information). Visual signal (EVIC) • Arcs are shown based on the obstacle’s distance and location relative to the vehicle. (Refer to “Rear Park Assist Display” for further information). I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 SIGNAL Failure MEANING Sensor or System failures INDICATION Visual Signal (instrument panel) • Icon appears on display. • Message is displayed on the Electronic Vehicle Information Center (EVIC) (where provided). While audible signals are emitted, the audio system is not Failure Indications muted. A malfunction of the Rear Park Assist sensors or system is The audible signal is turned off immediately if the indicated, during REVERSE gear engagement, by the indistance increases. The tone cycle remains constant if the strument panel warning icon and message displayed on distance measured by the inner sensors is constant. If this the Electronic Vehicle Information Center (EVIC) display. condition occurs for the external sensors, the signal is The warning icon is illuminated and a message turned off after 3 seconds (stopping warnings during is displayed on the EVIC display (if equipped). maneuvers parallel to walls). Refer to #Electronic Vehicle Information Center (EVIC)# in “Understanding Your Instrument Panel” for further information. I nf or mat i onPr ovi dedby: 3 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The sensors and wiring are tested continuously when the Park Assist System Usage Precautions ignition is in the ON/RUN position. Failures are indiNOTE: cated immediately if they occur when the system is ON. • Ensure that the outer surface and the underside of the Even if the system is able to identify that a specific sensor rear bumper is clean and clear of snow, ice, mud, dirt is in failure condition, the EVIC shall indicate that the or other obstruction to keep the Rear Park Assist Rear Park Assist system is unavailable, without reference system operating properly. to the sensor in failure condition. If even a single sensor fails, the entire system must be disabled. The system is • Jackhammers, large trucks, and other vibrations could turned off automatically. affect the performance of Rear Park Assist. Cleaning The Rear Park Assist System Clean the Rear Park Assist sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. In washing stations, clean sensors quickly keeping the vapor jet/high pressure washing nozzles at least 4 in (10 cm) from the sensors. Do not scratch or poke the sensors. Otherwise, you could damage the sensors. • Clean the Rear Park Assist sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The Rear Park Assist system might not detect an obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/bumper. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 • Objects such as bicycle carriers, etc., must not be placed within 12 in (30 cm) from the rear fascia/ bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing a failure indication to be displayed in the instrument cluster. CAUTION! (Continued) • The vehicle must be driven slowly when using Rear Park Assist in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using Rear Park Assist. CAUTION! • Rear Park Assist is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. (Continued) WARNING! • Drivers must be careful when backing up even when using the Rear Park Assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death. (Continued) I nf or mat i onPr ovi dedby: 3 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! (Continued) • Before using the Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns on the single flashing arc and sounds the continuous tone. Also, the sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle. The power sunroof roof switch is located in the overhead console. Power Sunroof Switch I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 To Open WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured. • Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result. Press and hold the power sunroof switch rearward for approximately one second and the sunroof will stop at the vented position. Press the switch a second time and hold for approximately one second and release, the sunroof will open fully, then stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. To Close With the sunroof in the full open position, pull the power sunroof button and hold it for approximately one second, the sunroof will return to the vented position. Pull the switch a second time and hold for approximately one second to completely close the sunroof. I nf or mat i onPr ovi dedby: 3 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Feature Emergency Operation This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an obstruction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close. In case of electrical failure the sunroof can be operated with the hex wrench that is located in the glove box. There is a plug located in the rear of the sunroof opening at the center of the vehicle. Removing the plug reveals a hex opening in the motor assembly of the sunroof. Insert the hex wrench and turn, moving the sunroof to the desired location. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sun Shade — If Equipped For vehicles equipped with either a power sunroof or a fixed glass roof, there is a sun shade that can be open or closed. To open the sun shade press the tab and move the shade to a full open position. I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 3 Manual Sun Shade Power Outlet Power is available when the ignition switch is in the There is a standard 12 Volt (13 Amp) power outlet, ON/RUN or START position. Insert the cigar lighter or located in the floor console, for added convenience. This accessory plug into the outlet for use. To preserve the heating element, do not hold the lighter in the heating power outlet can power mobile phones, electronics and position. other low power devices. ELECTRICAL POWER OUTLETS I nf or mat i onPr ovi dedby: 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watts (13 Amps) power rating is exceeded, the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty. Power Outlet Fuse Location Underhood F15 Fuse 15 A Blue Cigar Lighter Front Console I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 WARNING! CAUTION! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly. Only use these intermittently and with great caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery. I nf or mat i onPr ovi dedby: 3 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER — IF EQUIPPED CUPHOLDERS This is located on the center console, in front of the cup For the driver and front passenger, cupholders are loholders. To activate the cigar lighter, push and release the cated on the floor console between the front seats. knob. After a few seconds the knob automatically returns to its initial position, and the cigar lighter is ready for use. WARNING! When the cigar lighter is in use it becomes very hot. To avoid serious injury, handle the cigar lighter with care. Always check that the cigar lighter has turned off. Front Cupholders I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 For rear passengers, there are cupholders located on the STORAGE floor between the front driver and passenger seats. Glove Compartment The glove compartment is located on the right side of the instrument panel. Pull outward on the glove compartment latch to open the glove compartment. Push the glove compartment door upward to close it. Rear Cupholders Glove Compartment Latch I nf or mat i onPr ovi dedby: 3 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES The rear seatbacks have a fold down feature to allow increased cargo capacity. Push down the release button, located at the outboard top of the seatback and move the seatback to its foldeddown position to provide a flat load floor cargo area. When returning the seatback to its upright position, push rearward until the seatback is properly latched. Rear Seat Release Buttons I nf or mat i onPr ovi dedby: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located in the center of the instrument panel, below the radio. Press this button to turn on the rear window defroster. An indicator in the instrument cluster will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 20 minutes. To manually shut the defroster off, push the button a second time. Folded Rear Seats NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating. I nf or mat i onPr ovi dedby: 3 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ! INSTRUMENT PANEL FEATURES . . . . . . . . . .141 ! INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . .142 ! INSTRUMENT CLUSTER — ECO . . . . . . . . . . .143 ! INSTRUMENT CLUSTER — POP, LOUNGE, 500C . . . . . . . . . . . . . . . . . . . . . . . .144 ▫ Electronic Vehicle Information Center (EVIC) Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . .162 ▫ Change Engine Oil Indicator System . . . . . . . .164 ▫ Trip Computer . . . . . . . . . . . . . . . . . . . . . . .165 ▫ Trip Button . . . . . . . . . . . . . . . . . . . . . . . . . .165 ! INSTRUMENT CLUSTER DESCRIPTIONS . . . . .145 ▫ Trip Functions . . . . . . . . . . . . . . . . . . . . . . .166 ! ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . . . . . . . .159 ▫ Values Displayed . . . . . . . . . . . . . . . . . . . . . .167 ▫ EVIC Displays . . . . . . . . . . . . . . . . . . . . . . .160 ▫ Personal Settings (Customer-Programmable Features). . . . . . . . . . . . . . . . . . . . . . . . . . . .168 ▫ EVIC Control Buttons . . . . . . . . . . . . . . . . . .161 ! SALES CODE (RAB) RADIO . . . . . . . . . . . . . .180 I nf or mat i onPr ovi dedby: 4 140 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Introduction . . . . . . . . . . . . . . . . . . . . . . . . .181 ! iPod®/USB/MEDIA PLAYER CONTROL — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . ▫ Suggestions. . . . . . . . . . . . . . . . . . . . . . . . . .181 ! STEERING WHEEL AUDIO CONTROLS . . . . . ▫ Technical Specifications . . . . . . . . . . . . . . . . .183 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . ▫ Quick Guide . . . . . . . . . . . . . . . . . . . . . . . . .184 ▫ CD Player Operation . . . . . . . . . . . . . . . . . . ▫ General Information. . . . . . . . . . . . . . . . . . . .187 ▫ Operating Instructions — Hands-Free Phone ▫ Functions And Adjustments . . . . . . . . . . . . . .189 (If Equipped). . . . . . . . . . . . . . . . . . . . . . . . ▫ Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196 ! CD/DVD DISC MAINTENANCE . . . . . . . . . . ▫ SiriusXM Satellite Radio — If Equipped. . . . . .198 ! RADIO OPERATION AND MOBILE PHONES . ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . .201 ! CLIMATE CONTROLS . . . . . . . . . . . . . . . . . . ▫ CD MP3 Player . . . . . . . . . . . . . . . . . . . . . . .204 ▫ Manual Heating And Air Conditioning . . . . . ▫ Troubleshooting. . . . . . . . . . . . . . . . . . . . . . .206 ▫ Automatic Temperature Control (ATC) . . . . . .207 .208 .209 .209 .209 .209 .210 .210 .211 .213 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . .219 I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 141 INSTRUMENT PANEL FEATURES 4 1 2 3 4 5 6 — — — — — — Side Vent Multifunction Lever – Light Control Instrument Cluster And Warning Lights Windshield Wiper, Washer, Trip Computer Central Air Vents Storage Compartment/Radio 7 — Passenger Air Bag 8 — Glove Compartment 9 — Rear Defrost Button 10 — Hazard Button 11 — Climate Controls 12 — Power Windows Control I nf or mat i onPr ovi dedby: 13 14 15 16 — — — — Storage Compartment Shift Lever Sport Button Horn/Driver Airbag 142 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 143 INSTRUMENT CLUSTER — ECO 4 I nf or mat i onPr ovi dedby: 144 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — POP, LOUNGE, 500C I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 145 tire causes the tire to overheat and can lead to tire failure. 1. Tire Pressure Monitoring Telltale Light — If Equipped Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping Each tire, including the spare (if provided), ability. should be checked monthly when cold and Please note that the TPMS is not a substitute for proper inflated to the inflation pressure recommended tire maintenance, and it is the driver’s responsibility to by the vehicle manufacturer on the vehicle maintain correct tire pressure, even if under-inflation has placard or tire inflation pressure label. (If your vehicle not reached the level to trigger illumination of the TPMS has tires of a different size than the size indicated on the low tire pressure telltale. vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not tires.) As an added safety feature, your vehicle has been equipped operating properly. The TPMS malfunction indicator is with a Tire Pressure Monitoring System (TPMS) that illumi- combined with the low tire pressure telltale. When the nates a low tire pressure telltale when one or more of your system detects a malfunction, the telltale will flash for tires is significantly under-inflated. Accordingly, when the approximately one minute and then remain continuously low tire pressure telltale illuminates, you should stop and illuminated. This sequence will continue upon subsecheck your tires as soon as possible, and inflate them to the quent vehicle start-ups as long as the malfunction exists. INSTRUMENT CLUSTER DESCRIPTIONS proper pressure. Driving on a significantly under-inflated I nf or mat i onPr ovi dedby: 4 146 UNDERSTANDING YOUR INSTRUMENT PANEL When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size CAUTION! (Continued) equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket tire sealants may cause the Tire Pressure Monitoring System (TPMS) sensor to become inoperable. After using an aftermarket tire sealant it is recommended that you take your vehicle to an authorized dealership to have your sensor function checked. 2. Electronic Stability Control (ESC) OFF Indicator Light — If Equipped (Continued) I nf or mat i onPr ovi dedby: This light indicates the Electronic Stability Control (ESC) is off. UNDERSTANDING YOUR INSTRUMENT PANEL 147 3. Turn Signal Indicators The arrow will flash with the exterior turn signal when the turn signal lever is operated. NOTE: • A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. • Check for an inoperative outside light bulb if either indicator remains on and does not flash, or flashes at a rapid rate. 4. Electronic Stability Control (ESC) Activation/ Malfunction Indicator Light The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position. It should go out with the engine running. If the “ESC Activation/Malfunction Indicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. I nf or mat i onPr ovi dedby: 4 148 UNDERSTANDING YOUR INSTRUMENT PANEL driving, have the system inspected at an authorized • The “ESC Off Indicator Light” and the “ESC dealer as soon as possible. Refer to “Occupant Restraints” Activation/Malfunction Indicator Light” come on in “Things To Know Before Starting Your Vehicle” for momentarily each time the ignition switch is turned further information. to ON/RUN. 6. Park/Headlight ON Indicator — If Equipped NOTE: • Each time the ignition is turned to ON/RUN, the ESC system will be ON, even if it was turned off previously. This indicator will illuminate when the park lights or headlights are turned on. • The ESC system will make buzzing or clicking 7. High Beam Indicator sounds when it is active. This is normal; the sounds This light shows that the high beam headlights will stop when ESC becomes inactive following the are on. Push the multifunction control lever maneuver that caused the ESC activation. away from you to switch the headlights to high 5. Air Bag Warning Light beam. Pull the lever toward you to switch the headlights This light will turn on for four to eight seconds back to low beam. If the driver’s door is open, and the as a bulb check when the ignition switch is first headlights or park lights are left on, the high beam turned to ON/RUN. If the light is either not on indicator light will remain illuminated and a chime will during starting, stays on, or turns on while sound. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 149 8. Seat Belt Reminder Light testing, the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started. If the vehicle is not ready for emissions testing the light will come on when the ignition is first turned on and remain on for 15 seconds, then blink for 5 seconds, and remain on until the vehicle is started. If the bulb does not come on during starting, have the condition investigated promptly. When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s seat belt remains unbuckled, the seat belt reminder light will flash or remain on continuously. Refer to “Occupant Restraints” in “Things To Know Before If this light comes on and remains on while driving, it suggests a potential engine control problem and the need Starting Your Vehicle” for further information. for system service. 9. Malfunction Indicator Light (MIL) Although your vehicle will usually be drivable and not The Malfunction Indicator Light (MIL) is part need towing, see your authorized dealer for service as of an onboard diagnostic (OBDII) system soon as possible. which monitors the emissions and engine control system. If the vehicle is ready for emissions I nf or mat i onPr ovi dedby: 4 150 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Front Fog Light Indicator — If Equipped CAUTION! Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. WARNING! This indicator will illuminate when the front fog lights are on. 11. Electric Power Steering Malfunction Warning Light This telltale is on when the Electric Power Steering is not operating and needs service. 12. Rear Fog Light Indicator — If Equipped A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others. This indicator will illuminate when the rear fog lights are on. 13. Rear Defrost Indicator This indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 20 minutes. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 151 14. Brake Warning Light CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-lock Brake System reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. I nf or mat i onPr ovi dedby: 4 152 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions. The vehicle should have service performed, and the brake fluid level checked. WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the ABS, are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. If brake failure is indicated, immediate repair is necessary. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 153 Operation of the Brake Warning Light can be checked by 15. Anti-Lock Brake (ABS) Light turning the ignition switch from the OFF position to the This light monitors the Anti-lock Brake System ON/RUN position. The light should illuminate for ap(ABS). The light will turn on when the ignition proximately two seconds. The light should then turn off switch is turned to the ON/RUN position and unless the parking brake is applied or a brake fault is may stay on for as long as four seconds. detected. If the light does not illuminate, have the light If the ABS light remains on or turns on while driving, it inspected by an authorized dealer. indicates that the anti-lock portion of the brake system is The light also will turn on when the parking brake is not functioning and that service is required. However, applied with the ignition switch in the ON/RUN posi- the conventional brake system will continue to operate tion. normally if the BRAKE warning light is not on. NOTE: This light shows only that the parking brake is If the ABS light is on, the brake system should be serviced applied. It does not show the degree of brake application. as soon as possible to restore the benefits of anti-lock brakes. If the ABS light does not turn on when the ignition switch is turned to the ON/RUN position, have the light inspected by an authorized dealer. I nf or mat i onPr ovi dedby: 4 154 UNDERSTANDING YOUR INSTRUMENT PANEL 16. Gas Pedal Percentage Gauge/Turbo Gauge/ ECO Index Gauge Depending on what options and trim level your vehicle is equipped with there are three gauges available. • Gas Pedal Percentage Gauge: This gauge shows what percent the gas pedal is currently depressed at. • Turbo Gauge: This gauge shows the current turbo usage. • ECO Index Gauge: The ECO Index gauge allows the driver to monitor their driving style in order to increase fuel economy. The efficiency of the driving style is displayed on a gauge located on the right side of the instrument cluster and ranges from a minimum value of 0 up to a maximum value of 5 (0 = low, 5 = high). A higher “ECO” index indicates a more fuel efficient drive style and will increase your fuel economy. A lower “ECO” index indicates frequent accelerations/decelerations and will decrease your fuel economy. The index is recalculated approximately every second and takes into account a combination of the instant fuel economy and your driving style during the current trip. NOTE: Different trips may have different values even if the same driving style is maintained. Some factors that may impact the calculated index value are: • Traffic conditions • Trip duration • Temperature (engine and ambient) 17. Fuel Gauge Shows level of fuel in tank when ignition switch is in the ON/RUN position. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 155 18. Electronic Vehicle Information Center (EVIC) CAUTION! The EVIC features a driver-interactive display that is located in the instrument cluster. For further information, refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel.” 19. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an authorized dealer for service. WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle.” Follow the warnings under the “Cooling System Pressure Cap” paragraph. I nf or mat i onPr ovi dedby: 4 156 UNDERSTANDING YOUR INSTRUMENT PANEL before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ The tachometer indicates engine speed in Revolutions service, so that you can be sure that it is properly reset, or Per Minute (RPM x 1000). that the door jamb sticker is accurate if the odometer 21. Speedometer / Trip Odometer / Electronic Vehicle must be reset at zero. Information Center (EVIC) Display Area NOTE: If the vehicle is equipped with the Electronic This display indicates the total distance the vehicle has Vehicle Information Center (EVIC) in the instrument been driven. cluster, all warnings including “door” and “gate” and U.S. Federal regulations require that upon transfer of “Change Engine Oil” will only be displayed in the EVIC vehicle ownership, the seller certify to the purchaser the display. Refer to “Electronic Vehicle Information Center correct mileage that the vehicle has been driven. If your (EVIC) in “Understanding Your Instrument Panel.” odometer needs to be repaired or serviced, the repair 22. Low Fuel Light technician should leave the odometer reading the same When the fuel level reaches approximately as it was before the repair or service. If s/he cannot do so, 1.0 gallon (3.8L) this light will turn on, and remain then the odometer must be set at zero, and a sticker must on until fuel is added. be placed in the door jamb stating what the mileage was 20. Tachometer I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 157 23. Generic Warning Light 25. Charging System Light The Generic Warning Light will illuminate if any of the following conditions occur: Oil Change Request, Engine Oil Pressure Sensor Failure, External Light Failure, Fuel Cut-Off Intervention, Fuel Cut-Off Not Available, Parking Sensor Failure. This light shows the status of the electrical charging system. The light should come on when the ignition switch is first turned to ON/RUN and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the 24. Cruise On Indicator — If Equipped vehicle is experiencing a problem with the charging This light will turn on when the electronic system. Obtain SERVICE IMMEDIATELY. See an authospeed control is ON. For further information, rized dealer. refer to “Electronic Speed Control” in “Under- If jump starting is required, refer to “Jump Starting standing Your Instrument Panel.” Procedures” in “What To Do In Emergencies”. I nf or mat i onPr ovi dedby: 4 158 UNDERSTANDING YOUR INSTRUMENT PANEL 26. Electronic Throttle Control (ETC) Light 27. Oil Pressure Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the NEUTRAL position. The light should turn off. If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. The light will come on when the ignition is first turned to ON/RUN and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood. 28. Engine Temperature Warning Light This light warns of an overheated engine condition. The engine coolant temperature indicator will illuminate and a single chime will sound after reaching a set threshold. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 159 If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To Do In Emergencies” for further information. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster. 4 Electronic Vehicle Information Center (EVIC) Display I nf or mat i onPr ovi dedby: 160 UNDERSTANDING YOUR INSTRUMENT PANEL The EVIC consists of the following: EVIC Displays • System Status • Vehicle Information Warning Message Displays • Personal Settings (Customer-Programmable Features) • Outside Temperature Display • Trip Computer Functions • Tire Pressure Monitoring Display Instrument Cluster 1. Red Telltales (Left Bank) • Hood Ajar • Low Oil Pressure • Electronic Throttle Control I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 161 • Door Ajar • Speed Limiter — If Equipped 2. Amber Telltales • Ice Risk • Fuel Cut Off • Fuel Cut Off Failed • Hill Holder Failed • Oil Change Request • Check Lights • Vehicle Lock 3. Electronic Speed Control Active 4. Amber Telltales • Generic Warning Light • Glow Plug Light • Park Sensor Failed • Stop Lamp Failed 5. Red Telltales (Right Bank) • Trunk Ajar • Transmission Failure • Battery Charge Indicator 6. Exceeded Speed Limiter 7. Shift Up or Down Indicators 8. Gear Indicator EVIC Control Buttons Push and release the MENU button briefly to access the EVIC. Push and hold the MENU button (approximately one second) to return to the main screen. button to scroll upward Push and release the UP through the displayed menu and the related options or to increase the displayed value. I nf or mat i onPr ovi dedby: 4 162 UNDERSTANDING YOUR INSTRUMENT PANEL button to scroll down- Electronic Vehicle Information Center (EVIC) Push and release the DOWN ward through the displayed menu and the related Setup Menu options or to decrease the value displayed. The menu comprises a series of functions arranged in a NOTE: UP and DOWN buttons activate differ- cycle. Push and release the UP and DOWN butent functions according to the following situations: tons to access the different options and settings (setup). • To scroll the menu options upwards or downwards. The setup menu can be activated by pushing the MENU or DOWN butbutton. A single push on the UP NOTE: When opening one of the front doors, the EVIC tons will scroll through the setup menu options. The display will turn on the clock and the miles or kilometers menu includes the following functions: covered (for versions/markets, where provided) for a • Speed Beep few seconds. • To increase or decrease values during settings. • Trip B Data • Set Time • Set Date I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 163 • See Radio Selecting An Option Of The Main Menu Without Submenu • Autoclose 1. Briefly push and release the MENU button to select the main menu option to set. • Speed Display • Units • Language • Buzzer Volume • Button Volume • Daylights (D.R.L.) • Hill Start or DOWN button (by 2. Push and release the UP single pushes) to select the new setting. 3. Briefly push and release the MENU button to store the new setting and go back to the main menu option previously selected. Selecting An Option Of The Main Menu With Submenu • Tire Pressure 1. Briefly push and release the MENU button to display the first submenu option. • Unlock All Doors or DOWN button (by 2. Push and release the UP single pushes) to scroll through all the submenu options. • Unlock Driver Door First • Exit Menu I nf or mat i onPr ovi dedby: 4 164 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Briefly push and release the MENU button to select after a single chime has sounded to indicate the next the displayed submenu option and to open the rel- scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the evant setup menu. engine oil change interval may fluctuate, dependent or DOWN button (by 4. Push and release the UP upon your personal driving style. single pushes) to select the new setting for this Unless reset, this message will continue to display each submenu option. time you turn the ignition switch to the ON/RUN 5. Briefly push and release the MENU button to store the position. To turn off the message temporarily, push and new setting and go back to the previously selected release the MENU button. To reset the oil change indicasubmenu option. tor system (after performing the scheduled maintenance), 6. Push and hold the MENU button to return to the main refer to the following procedure. menu (short hold) or the main screen (longer hold). 1. Turn the ignition switch to the ON position. (do not start the engine.) Change Engine Oil Indicator System Change Engine Oil 2. Fully push the accelerator pedal slowly, three times within 10 seconds. Your vehicle is equipped with an engine oil change indicator system. The “Change Engine Oil” message will 3. Turn the ignition switch to the OFF/LOCK position. flash in the EVIC display for approximately 10 seconds I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 165 NOTE: If the indicator message illuminates when you New Trip start the vehicle, the oil change indicator system did not To reset: reset. If necessary, repeat this procedure. • Push and hold the TRIP button to reset the system Trip Computer manually. The Trip Computer is located in the instrument cluster. It • When the “Trip distance” reaches 9999.9 miles or features a driver-interactive display (displays informakilometers or when the “Travel time” reaches 999.59 tion such as trip information, range, fuel consumption, (999 hours and 59 minutes), the system is reset autoaverage speed, and travel time). matically. Trip Button • Disconnecting/Reconnecting the battery resets the The TRIP button, located on the right steering column system. stalk, can be used to display and to reset the previously NOTE: If the reset operation occurs in the presence of described values. the screens concerning Trip A or Trip B, only the infor• A short button push displays the different values. mation associated with Trip A or Trip B functions will be • A long button push resets the system and then starts a reset. new trip. I nf or mat i onPr ovi dedby: 4 166 UNDERSTANDING YOUR INSTRUMENT PANEL Start Of Trip Procedure • Average consumption With the ignition on, push and hold the TRIP button for • Instantaneous consumption over one second to reset. • Average speed A Exit Trip • Travel time A (driving time) To exit the Trip function, wait until all the values have been displayed or hold the MENU button for longer than one “Trip B” can be used to display the figures relating to: second. • Trip distance B Briefly push and release the MENU button to go back to the • Average consumption menu screen or push and hold the MENU (approximately one second) to go back to the main screen without storing • Average speed B settings. • Travel time B (driving time) Trip Functions NOTE: “Trip B” functions may be excluded (see “Trip Both trip functions are resettable (reset — start of new trip). B Data”). “Range” and “Instantaneous consumption” cannot be reset. “Trip A” can be used to display the figures relating to: • Range • Trip distance A I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 167 Values Displayed Average Economy Range This value shows the approximate average consumption since the last reset. This indicates the distance which may be traveled with the fuel remaining in the tank, assuming that driving Instant Economy conditions will not change. The message “----” will This indicates the fuel consumption. The value is conappear on the display in the following cases: stantly updated. The message “----” will appear on the • Distance less than 30 miles (or 50 km). display if the car is parked with the engine running. • The vehicle is parked for a long time with the engine Average Speed running. This value shows the vehicle’s average speed as a funcNOTE: The range depends on several factors: driving tion of the overall time elapsed since the last reset. style, type of route (freeway, residential, mountain roads, Travel Time etc.), conditions of use of the car (load, tire pressure, etc.). This value shows the time elapsed since the last reset. Trip planning must take into account the above notes. Distance Traveled This value shows the distance covered since the last reset. I nf or mat i onPr ovi dedby: 4 168 UNDERSTANDING YOUR INSTRUMENT PANEL Personal Settings (Customer-Programmable Features) Speed Beep (Speed Limit) With this function, it is possible to set the car speed limit (mph or km/h) to immediately alert the driver when the The EVIC display is provided with a light sensor capable set limit is exceeded. of detecting environmental light conditions and adjusting the brightness of the instruments accordingly. To set the speed limit, proceed as follows: Dimmer NOTE: The brightness of the instrument panel may change 1. Briefly push and release the MENU button to enter the while travelling following an event that causes switching Main MENU. from “day” to “night” conditions (or vice versa) in the or DOWN button to passenger compartment (e.g. in a tunnel, on avenues in 2. Push and release the UP select Speed Beep. Push and release the MENU shadows, under bridges, etc.). or DOWN button, push and release the UP To adjust the brightness, proceed as follows: buttons to select Speed Limit activation (On) or deactivation (Off). or DOWN button to 1. Push and release the UP set the required brightness level. 3. When the function is activated (On), briefly push and release the MENU button to display the presently set 2. Briefly push and release the MENU button to go back to or DOWN activation speed. Pushing the UP the menu screen or push and hold the MENU (approxibuttons selects the speed limit. Push and release mately one second) to go back to the main screen the MENU button to confirm selection. without storing settings. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 169 NOTE: The setting can be increased or decreased by 3. Briefly push and release the MENU button to go back 5 mph or km/h each time the UP/DOWN button is to the menu screen, or push and hold the MENU pushed for speed settings above 20 mph (32 km/h). To button (approximately one second) to go back to the increase or decrease the set speed rapidly, push and hold main screen without storing the settings. the UP/DOWN button. Save the setting by briefly pushTrip B Data (Trip B On) ing the button when you approach the required setting. Through this option, it is possible to activate (On) or • Briefly push and release the MENU button to go back deactivate (Off) the Trip B (partial trip) display. to the menu screen, or push and hold the MENU button (approximately one second) to go back to the For further information see “Trip Computer.” main screen without storing the settings. For activation / deactivation, proceed as follows: To cancel the setting, proceed as follows: 1. Briefly push and release the MENU button. 1. Briefly push and release the MENU button. “On” will 2. Push and release the UP or DOWN button to flash on the display. select Trip B data. Push and release the UP or button. “Off” will 2. Push and release the DOWN buttons to turn ON or OFF DOWN flash on the display. I nf or mat i onPr ovi dedby: 4 170 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Briefly push and release the MENU button to go back 4. When accessing the “Time” sub-menu item, briefly push and release the MENU button and “hours” will to the menu screen, or push and hold the MENU flash on the display. button (approximately one second) to go back to the main screen without storing the settings. 5. Push and release the UP or DOWN button for setting. Set Time (Clock) This function may be used to set the clock through two 6. Briefly push and release the MENU button and “minsubmenu items: “Time” and “Mode.” utes” will flash on the display. Proceed as follows: 7. Push and release the UP setting. or DOWN button for 1. Briefly push and release the MENU button. Push and or DOWN buttons to highlight NOTE: release the UP Set Time — Push and release the MENU button. • The setting will increase or decrease by one unit each time the UP or DOWN button is pushed. 2. Push and release the UP or DOWN button to Push and hold the button to increase/decrease the navigate the two sub-menu items. setting rapidly. Save the setting by briefly pushing 3. Select the required option and then push and release the button when you approach the required setting. the MENU button. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 171 • Briefly push and release the MENU button to return To change the date proceed as follows: to the “Time” sub-function. 1. Briefly push and release the MENU button. Push and • When accessing the “Mode” submenu, briefly push release the UP or DOWN button to highlight and release the MENU button. The previously set Date, push and release the MENU button and Year display format will flash on the display. will begin to flash. • Push and release the UP select “24h” or “12h.” or DOWN button to 2. Push and release the UP setting. or DOWN button for When you have selected the required settings, briefly 3. Briefly push and release the MENU button and push and release the MENU button to go back to the “month” will flash on the display. Time, Mode sub-menu screen, or push and hold the or DOWN button for MENU button (approximately one second) to go back to 4. Push and release the UP setting. the main screen without storing the settings. 5. Briefly push and release the MENU button and “day” Set Date will flash on the display. This function may be used to set the date (day - month or DOWN button for 6. Push and release the UP year). setting. I nf or mat i onPr ovi dedby: 4 172 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The setting will increase or decrease by one unit To activate (On) or to deactivate (Off) the sound system or DOWN button is pushed. info displaying proceed as follows: each time the UP or DOWN button to Push and hold the UP 1. Briefly push and release the MENU button. Push and increase/decrease the setting rapidly. Save the setting release the UP or Down button to highlight by briefly pushing the button when you approach the See Radio and push and release the MENU button. required setting. 2. Push and release the UP or DOWN button for • Briefly push and release the MENU button to go back setting. to the menu screen, or push and hold the MENU button (approximately one second) to go back to the 3. Briefly push and release the MENU button to go back to the menu screen, or push and hold the MENU main screen without storing the settings. button (approximately one second) to go back to the See Radio (Repeat Audio Information) main screen without storing the settings. With this function active, the EVIC display shows inforIf the radio has BLUE&ME™, refer to the appropriate mation relevant to the sound system. “BLUE&ME™ Radio Supplement” for further informa• Radio: tuned radio station frequency, automatic tuning tion. activation or AutoStore. • CD audio, CD MP3: track number. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 173 Speed Display Autoclose When this function is activated the cluster will display With this function active, the doors will automatically the vehicle speed (MPH or km/h). lock at when the vehicle’s speed exceeds 15 mph (24 km/h). To activate (On) or to deactivate (Off) the speed display feature, proceed as follows: To change the setting proceed as follows: 1. Briefly push and release the MENU button. Push and 1. Briefly push and release the MENU button. Push the or DOWN button to highlight release the UP or DOWN button to highlight Autoclose. UP Speed Display. Push and release the MENU button Push and release the MENU button to enter Autoto enter the Speed Display MENU. close MENU. 2. Push and release the UP or DOWN button to 2. Push and release the UP select display deactivation “Off”, “MPH” or “km/h”. setting. or DOWN button for 3. Briefly push and release the MENU button to go back 3. Briefly push and release the MENU button to go back to the menu screen, or push and hold the MENU to the menu screen, or push and hold the MENU button (approximately one second) to go back to the button (approximately one second) to go back to the main screen. main screen without storing the settings. I nf or mat i onPr ovi dedby: 4 174 UNDERSTANDING YOUR INSTRUMENT PANEL or DOWN button for 5. Push and release the UP setting. This function may be used to set the measurement unit in three submenus: “Distance,” “Temperature” and “Fuel 6. Briefly push and release the MENU button to return to Economy, and Tire Pressure.” the sub-menu. Units (Set Units) To set the required unit, proceed as follows: 7. When accessing the “Fuel Economy” submenu, briefly push and release the MENU button. Either “mpg,” 1. Briefly push and release the MENU button. Push and “km/l ” or “l/100km” will appear on the display or DOWN button to highlight release the UP (according to the previous setting). Units. Push and release the MENU button to enter Units MENU. If the distance unit set is “mi,” the fuel economy unit will 2. Push and release the UP or DOWN button to be displayed in “mpg.” navigate the three sub-menus. If the distance unit set is “km,” the fuel economy unit will 3. Select the required sub-menu and then briefly push be displayed in either km/l or l/100km. and release the MENU button. or DOWN button for 1. Push and release the UP setting. 4. When accessing the “Distance” submenu: briefly push and release the MENU button. Either “mi” or “km” will 2. Briefly push and release the MENU button to return to appear on the display (according to the previous setting). the sub-menu. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 175 3. When accessing the “Temperature” submenu: briefly push and release the MENU button. Either “°F” or “°C” will appear on the display (according to the previous setting). 4. Push and release the UP setting. or DOWN button for Language (Selecting The Language) The messages can be displayed in the following languages: Italian, English, Turkce, Nederlands, Spanish, French, Dutch, Polish, Brasilian. To set the required language, proceed as follows: 1. Briefly push and release the MENU button. Push and or DOWN button to highlight release the UP Language. Push and release the MENU button to enter the Language MENU. When you have made the required settings, briefly push and release the MENU button to go back to the sub-menu 2. Push and release the UP or DOWN button for screen, or push and hold the MENU button (approxisetting. mately one second) to go back to the main screen without 3. Briefly push and release the MENU button to go back storing the settings. to the menu screen, or push and hold the MENU button (approximately one second) to go back to the main screen without storing the settings. 5. Briefly push and release the MENU button to return to the Tire Pressure — PSI/KPA sub-menu. I nf or mat i onPr ovi dedby: 4 176 UNDERSTANDING YOUR INSTRUMENT PANEL Buzzer Volume (Adjusting The Failure/Warning Buzzer Volume) Button Volume (Button Volume Adjustment) To adjust the volume proceed as follows: To adjust the volume, proceed as follows: This function may be used to adjust the volume of the With this function the volume of the buzzer accompany- beep accompanying the buttons. MENU, UP or ing any failure/warning indication can be adjusted to DOWN buttons can be adjusted according to one of eight volume levels. 8 levels. 1. Briefly push and release the MENU button. Push and 1. Briefly push and release the MENU button. Push and or DOWN button, then highrelease the UP or DOWN button to highlight release the UP light the Buzzer Volume. Push and release the the Buzzer Volume, push and release the MENU MENU button to enter the Buzzer Volume MENU. button. 2. Push and release the UP or DOWN button for 2. Push and release the UP or DOWN button for setting. setting. 3. Briefly push and release the MENU button to go back 3. Briefly push and release the MENU button to go back to the menu screen, or push and hold the MENU to the menu screen, or push and hold the MENU button (approximately one second) to go back to the button (approximately one second) to go back to the main screen without storing the settings. main screen without storing the settings. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 177 3. Push and release the UP or DOWN button for setting. This function will only be displayed after a FIAT Group Automobiles dealership has deactivated the S.B.R. system. 4. Briefly push and release the MENU button to go back to the menu screen, or push and hold the button Daytime Running Lamps (DRL) (approximately one second) to go back to the main This function may be used to activate / deactivate the screen without storing the settings. Daytime Running Lamps. GSI (Gear Shift Indicator) Proceed as follows to switch this function on or off: This function may be used to set the Gear Shift Indicator 1. Briefly push and release the MENU button. Push and in two submenus: “Fuel Econ On” and “Fuel Econ Off.” or DOWN button to highlight release the Up Daytime Running Lamps (DRL). Push and release • Fuel Econ On – turns on a fuel economy upshift light in the instrument cluster, for optimum fuel economy, the MENU button to enter the DRL MENU. when operating in base driving mode. 2. Briefly push and release the MENU button. “On” or “Off” will flash on the display (according to previous • Fuel Econ Off – the fuel economy upshift light is disabled. setting). Belt Buzzer (Buzzer Activation For S.B.R. Indication) I nf or mat i onPr ovi dedby: 4 178 UNDERSTANDING YOUR INSTRUMENT PANEL To set the required unit, proceed as follows: Hill Start Assist 1. Briefly push and release the MENU button to display This function is used when starting a vehicle from a stop on a hill. Hill Start Assist maintains the same level of the two sub-menus. brake pressure the driver applied for a short period of or DOWN button to 2. Push and release the UP time after the foot has been removed from the brake navigate the two sub-menus. pedal. 3. Select the required sub-menu and then briefly push Proceed as follows to switch this function on or off: and release the MENU button. 1. Briefly push and release the MENU button. Push and or DOWN button for 4. Push and release the UP or DOWN button to highlight release the UP setting. the Hill Start Assist. Push and release the MENU button to enter the Hill Start Assist MENU. 5. Briefly push and release the MENU button to return to the sub-menu. 2. Push and release the UP or DOWN button for setting. When you have made the required settings, briefly push and release the MENU button to go back to the sub-menu 3. Briefly push and release the MENU button to go back screen, or push and hold the MENU button (approxito the menu screen, or push and hold the button mately one second) to go back to the main screen without (approximately one second) to go back to the main storing the settings. screen without storing the settings. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 179 Tire Pressure Lock This function will be used to display the tire pressures When Unlock Driver Door is selected, only the driver’s individually for all four tires by location. door will unlock on the first push of the Remote Keyless Entry (RKE) transmitter UNLOCK button. When Unlock Proceed as follows: Drivers Door is selected, you must push the RKE trans1. Briefly push and release the MENU button. Push and mitter UNLOCK button twice to unlock the passenger or DOWN button to highlight door. When All Doors is selected, both of the doors will release the UP the Tire Pressure. Push and release the MENU unlock on the first push of the RKE transmitter UNLOCK button to enter the Tire Pressure MENU. button. To make your selection, push and release the SELECT button until “Unlock Driver Door” or “All 2. Push and release the UP or DOWN button to scroll Doors” appears. through all four tire pressure value locations. 3. Briefly push and release the MENU button to go back to the menu screen, or push and hold the button (approximately one second) to go back to the main screen. I nf or mat i onPr ovi dedby: 4 180 UNDERSTANDING YOUR INSTRUMENT PANEL Exit Menu SALES CODE (RAB) RADIO This function closes the initial menu screen. Briefly push and release the MENU button to go back to the main screen. button to return to the first Push and release the menu option (Speed Beep). Push and release the button to return to the last menu option (Daylights). RAB Radio I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 181 Reception Conditions Introduction The radio has been designed according to the specifica- Reception conditions change constantly while driving. tions of the passenger compartment, with a personalized Reception may be interfered with by the presence of design to match the style of the dashboard. mountains, buildings or bridges, or when you are far away from the broadcaster. If the radio has BLUE&ME™, refer to the appropriate “BLUE&ME™ User’s Manual” for further information. The instructions for use are given below and we recommend you to read them carefully. Suggestions Road Safety Please, learn how to use all different radio functions (e.g. store stations) before beginning to drive. WARNING! Having the volume turned up high can cause the driver to not be able to hear important traffic sounds, i.e. sirens, horns, etc. Failure to hear traffic sounds and other important audible information can result in serious injury or death. Always adjust the volume so that you can still hear background noises. Care And Maintenance Clean the cover with a soft antistatic cloth only. Cleaning and polishing products could damage the surface. I nf or mat i onPr ovi dedby: 4 182 UNDERSTANDING YOUR INSTRUMENT PANEL • Do not stick labels on the CD surface or write on the recorded surface with pencils or pens. CDs The presence of dirt, scratches or distortions on the CDs could cause skipping and poor sound quality while it is • Do not use CDs that are very scratched, flawed, playing. For optimal playback conditions, follow these distorted, etc. Using discs like these will result in guidelines: malfunctions or damage to the player. • Only use branded CDs. • The use of original CD media is required for the best quality audio production. Correct operation is not • Clean every CD thoroughly removing any finger guaranteed when CD-R/RW media are used that were marks or dust using a soft cloth. Hold CDs by the not correctly burned and/or with a maximum capacity outside and clean them from the middle outwards. above 650 Mb. • Never use chemicals (e.g. antistatics or thinners or sprays) for cleaning as they could damage the surface • Do not use commercially available protective sheets for CDs or discs, with stabilizers, etc. as they could get of the CDs. stuck in the internal mechanism and damage the disc. • After listening to them place CDs back in their boxes to prevent them from being damaged. • Do not expose CDs to direct sunlight, high temperatures or moisture for long periods. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 183 • If a copy-protected CD is used, it may take a few seconds before the system starts to play it. The CD player cannot be guaranteed to play all protected discs. The fact that the CD is protected from being copied is often shown in very small letters or is difficult to read on the actual CD cover where it may be, for example, “COPY CONTROL,” “COPY PROTECTED,” “THIS CD CANNOT BE PLAYED ON A PC/MAC.” Technical Specifications The complete system consists of: • Two 165 mm diameter midwoofer speakers, one speaker in each of the front doors. • Two 22 mm diameter tweeter speakers, one speaker in each of the front pillars. • Two 100 mm diameter full range speakers, one speaker in each of the rear side panels. • The CD player is capable of reading most compression systems currently in use, following the development of • Antenna on the car roof. these systems, the reading of all compression formats • Radio with CD/MP3 player. is not guaranteed. I nf or mat i onPr ovi dedby: 4 184 UNDERSTANDING YOUR INSTRUMENT PANEL With Alpine Premium Audio system (if equipped): • Antenna on the car roof. • Two 165 mm diameter midwoofer speakers. • Radio with CD/MP3 player. With BEATS Premium Audio system (if equipped): • Two 11 mm tweeter speakers in the front pillars. • Two 100 mm full range speakers, one speaker in each • A subwoofer in the trunk on the left-hand side panel. of the rear side panels. • An amplifier in the trunk on the right-hand side panel. Quick Guide Radio Controls BUTTON TUNER A-B-C GENERAL FUNCTIONS On Off AM, FM, SAT (if equipped) source selection Cycles A, B, C presets for AM, FM, SAT (if equipped) I nf or mat i onPr ovi dedby: MODE Short button push Short button push Short repeated button push Short repeated button push UNDERSTANDING YOUR INSTRUMENT PANEL 185 BUTTON MEDIA GENERAL FUNCTIONS CD/AUX/Media Player (if equipped and present) source selection BUTTON (Mute/Pause Button) AUDIO (Information Button) GENERAL FUNCTIONS Volume activation/deactivation (Mute/Pause) Audio adjustments: low tones (BASS), high tones (TREBLE), left/ right balance (BALANCE), front/ rear balance (FADER) Song, Artist, Album, Genre, Playlist, Folder information (if available) in CD, Media Player and Satellite (if so equipped); Toggles RBDS information in FM I nf or mat i onPr ovi dedby: MODE Short repeated button push MODE Short button push Menu activation: short button push Adjustment type selection: push or Adjustment of values: push or 4 186 UNDERSTANDING YOUR INSTRUMENT PANEL BUTTON MENU GENERAL FUNCTIONS Advanced functions adjustment +Vol/–Vol Volume adjustment BUTTON RADIO FUNCTIONS Radio Station Search: • Automatic Search • Manual Search 12345 Current radio station storing Stored station recall I nf or mat i onPr ovi dedby: MODE Menu activation: short button push or Adjustment type selection: push Adjustment of values: push or Push + button: volume increase Push – button: volume decrease MODE Automatic search: push buttons or (long push for fast forward) Manual search: push buttons or (long push for fast forward) Long button push for memory preset 1 to 5 respectively Short button push for memory preset 1 to 5 respectively UNDERSTANDING YOUR INSTRUMENT PANEL 187 BUTTON CD FUNCTIONS CD ejection Previous/next track play CD track fast forward/rewind Previous/next folder play (for CD-MP3) General Information The radio offers the following functions: Radio Section • PLL tuning with FM/AM bands • RBDS (Radio Broadcast Data System) • Automatic/manual station tuning • FM Multipath detector MODE Short button push Short button push Long button push Short button push or or or • Manual storing of 25 stations (base radio) and 40 stations (if equipped with Satellite): 15 on FM band (5 on FMA, 5 on FMB, 5 on FMC), 10 on AM band (5 on AMA, 5 on AMB), 15 on Satellite Band - if equipped (5 on SATA, 5 on SATB, 5 on SATC) • SPEED VOLUME function: Customer selectable automatic volume adjustment depending on the car speed • Automatic Stereo/Mono selection I nf or mat i onPr ovi dedby: 4 188 UNDERSTANDING YOUR INSTRUMENT PANEL • Track selection (forward/backward) CD Section • Fast forward/rewind through tracks • Track selection (forward/backward) • MP3 Display function: display of folder name, ID3-TAG information, time elapsed since the start of • CD Display function: display of track number and on the track, name of the file mp3 discs (song title, artist) and time elapsed since • Playing audio or data CD, CD-R and CD-RW start of the track • Fast forward/rewind through tracks • Playing Audio CD, CD-R and CD-RW Audio Section • Mute/pause function CAUTION! On multimedia CDs, besides audio tracks, there are data tracks too. Playing this type of CD could cause hissing at a volume that could damage the speakers. CD/MP3 Section • MP3-Info function (ID3-TAG) • Folder selection (previous/next) • Soft mute function • Loudness function • Graphic 7 band equalizer (if equipped) • Separate bass/treble tone adjustment • Right/left channel balancing • Front/rear fader I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 189 Functions And Adjustments Selecting The CD Function Turning The Car Radio On By briefly pushing the MEDIA button, the CD audio source can be selected (only if a CD is loaded). The car radio comes on when the is pushed briefly. (ON/OFF) button Volume Adjustment When the car radio is turned on and the on volume limit To adjust the volume, push the buttons +Vol or –Vol to is on, the volume is limited to a setting of five even if it increase/decrease the volume. had been set higher when previously used. Mute/Pause Function Turning The Car Radio Off Push the button briefly to activate the MUTE funcPush the (ON/OFF) button to turn the radio off. Selecting The Radio Functions tion. The volume will gradually decrease and the wording “TUNER Mute” will be shown on the display (in radio mode) or “CD Pause” (in CD mode). By pushing the TUNER button briefly and repeatedly, the Push the button again to deactivate the MUTE following audio sources can be selected cyclically: function. The volume will gradually increase until it • AM, FM and Satellite Bands (if equipped) reaches the previously set level. I nf or mat i onPr ovi dedby: 4 190 UNDERSTANDING YOUR INSTRUMENT PANEL When the volume level is changed using the dedicated The current status of the selected function appears on the controls, the Mute function is deactivated and the vol- display. ume is adjusted to the new level selected. The functions managed by the Audio Menu are: Audio Adjustment • BASS (Bass adjustment) The functions that can be selected from the audio menu change depending on the context: AM/FM/MEDIA/ • MIDRANGE (Midrange adjustment) SATELLITE. • TREBLE (Treble adjustment) Push the AUDIO button briefly to change the Audio • BALANCE (right/left Balance adjustment) functions. After the AUDIO button is first pushed, the display will show the Bass level value for the source • FADER (front/rear Balance adjustment) activated at that time (e.g. in FM mode the display will • LOUDNESS — if equipped (Loudness function show the wording “FM Bass +2”). activation/deactivation) or to scroll through the Menu • EQUALIZER — if equipped (activation and selection Use the buttons functions. To change the setting of the selected funcof factory equalization adjustments) or buttons. tion, use the • USER EQUALIZER — if equipped (customized equalization adjustment) I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 191 Tone Adjustment Balance Adjustment Proceed as follows: Proceed as follows: 1. Push the AUDIO button. 1. Push the AUDIO button. or button to select “Bass,” “Mid- 2. Push the or 2. Push the range” or “Treble” in the AUDIO menu. AUDIO menu. button to set “Balance” in the 3. Push the or button to increase/decrease the 3. Push the button to increase the sound from the button to increase the sound bass or treble adjustments. left speakers or the from the right speakers. By pushing the or buttons briefly, the levels will change progressively. By pushing them down longer, By pushing the or buttons briefly, the levels will the levels will change quickly. change progressively. By pushing them down longer, the levels will change quickly. Select the value “0” to set the right and left audio outputs at the same level. I nf or mat i onPr ovi dedby: 4 192 UNDERSTANDING YOUR INSTRUMENT PANEL Fader Adjustment Loudness Function — If Equipped Proceed as follows: The Loudness function improves the volume of the sound while listening at low volumes, increasing the bass and treble. 1. Push the AUDIO button. or 2. Push the AUDIO menu. button to set “Fader” in the To activate/deactivate this function, select the “Loudness” setting in the AUDIO menu. The condition of the 3. Push the button to increase the sound coming function (on or off) is shown on the display for a few button to increase seconds by the wording “Loudness On” or “Loudness from the rear speakers or the the sound coming from the front speakers. Off”. By pushing the or buttons briefly, the levels will Preset/User/Classic/Rock/Jazz Functions — If change progressively. By pushing them down longer, Equipped the levels will change quickly. The built-in equalizer can be activated/deactivated. Select the value “0” to set the right and left audio outputs When the equalizer function is off, the audio settings can only be changed by adjusting the “Bass” and “Treble” at the same level. settings, whereas when the function is on, the acoustic curves can be adjusted. To deactivate the equalizer, select the “EQ Preset” function in the audio menu. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 193 To activate the equalizer, use the AUDIO button to select User EQ Settings Function — If Equipped one of the adjustments: To set a personalized equalizer adjustment: • “EQ User” (adjustment of 7 equalizer bands that can 1. Push the AUDIO button. be changed by the user) or buttons to set EQ function. 2. Use the • “Classic” (equalizer preset for optimal classic music 3. Use or buttons to select #EQ User.# sound) • “Rock” (equalizer preset for optimal rock and pop 4. Push the MENU button to start adjusting equalizer. music sound) 5. On the display a seven bar graph will appear, in which each bar represents a frequency. Select the bar to be • “Jazz” (equalizer preset for optimal jazz music sound) or buttons. The selected adjusted by using the When one of the equalizer adjustments is activated the bar will start to flash and it can be adjusted using wording “EQ” lights up. or buttons. 6. To store the setting, push the MENU or AUDIO buttons. I nf or mat i onPr ovi dedby: 4 194 UNDERSTANDING YOUR INSTRUMENT PANEL Menu MENU Button Functions • System Reset • Speed Volume Push the MENU button briefly to activate the Menu • On Volume Limit function. Push the MENU button again to exit the Menu function. or buttons to scroll through the menu Use the functions. To change the setting of the selected func- Speed Volume Function — If Equipped This function automatically adapts the volume level to the or buttons. tion, use the speed of the car, turning up the volume when the speed The current status of the selected function appears on the increases to maintain the ratio with the noise level inside display. the passenger compartment. To activate/deactivate the function, use the buttons. The wording “Speed volume” The functions managed by the Menu are: appears on the display, followed by the current status of • Speech Volume the function: • Aux Audio Offset • Off: function deactivated • Radio Off • Low: function activated (low sensitivity) • Sat ID • High: function activated (high sensitivity) • SiriusXM Telephone Number I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 195 • “On volume limit: off” – The radio will come on at the same volume as before it was switched off. The This function makes it possible to activate/deactivate the volume level can be between 0 and 40. maximum volume limit when turning the radio on. or to change the setting. Use the buttons The display shows the function status: NOTE: • “On volume limit: on” – when the radio is turned on the volume level will be: • Using the Menu it is only possible to adjust the activation/deactivation of the function and not the – If the volume level is equal to or higher than the minimum or maximum volume value. maximum value, the radio will come on at the maximum volume. • If the battery charge is too low, the volume cannot be – If the volume level is between the minimum and adjusted between the minimum and the maximum maximum values, the radio will come on at the level. same volume as before it was switched off. – If the volume level is equal to or lower than the minimum value, the radio will come on at the minimum volume. On Volume Limit I nf or mat i onPr ovi dedby: 4 196 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Off Function System Reset Function This function makes it possible to set the radio switching This function is used to restore all settings to the factory off mode by choosing between two methods. values. The options are: The chosen mode appears on the display: • NO — No restore intervention. • “Radio off: 00 min” — The radio turns off in connec- • YES — The default parameters will be restored. Durtion with the ignition key; the radio is turned autoing such operation, the wording “Resetting” appears matically off as soon as the key is turned to the STOP on the display. At the end of the operation, the source position. does not change and the previous situation will be displayed. • “Radio off: 20 min” — The radio turns off independently from the ignition key; the radio remains on for Radio a maximum period of 20 minutes after the key has (Tuner) Introduction been turned to the STOP position. When the car radio is turned on, the last function that was selected before turning it off (Radio, CD, CD MP3, AUX) is activated. To select the Radio function when another audio source is being listened to, briefly push the TUNER button. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 197 Once the Radio mode has been activated, the display will Preset Buttons show the name (RBDS stations only) or the frequency of The buttons numbered from 1 to 5 are used to set the the selected radio station, the frequency band selected following pre-selections: (e.g. FMA) and the preset button number (e.g. P1). • 15 in the FM band (5 in FMA, 5 in FMB, 5 in FMC) Frequency Band Selection • 10 in the AM band (5 in AMA, 5 in AMB) With the Radio mode active, press the FM or AM tuner button briefly and repeatedly to select the desired recep- • 15 in SAT (if so equipped) (5 SATA, 5 SATB, 5 SATC) tion band. To listen to a preset station, select the desired frequency Each time the button is pressed the following bands are band and then briefly push the corresponding preset selected cyclically: button (from 1 to 5). • AM, FM or SAT (if equipped) By pushing the preset button for more than two seconds, the tuned station will be stored. Pushing the A-B-C Each band is highlighted by the corresponding wordings button will change between the preset memory group in on the display. The radio will be tuned to last station the current frequency band. selected on the respective frequency band. I nf or mat i onPr ovi dedby: 4 198 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Tuning Stereophonic Broadcasters Briefly push the or button to start the automatic If the incoming signal is weak, the reproduction is tuning search for the next station that can be received automatically switched from Stereo to Mono. in the selected direction. SiriusXM Satellite Radio — If Equipped If the or button is pushed for longer, the rapid SiriusXM Satellite Radio search is started. When the button is released, the tuner will stop on the next station that can be received. With over 130 channels, SiriusXM Satellite Radio brings you more of what you love. Get 69 channels of 100% commercialManual Tuning free music, plus all of your favorite sports, news, talk and This is used to manually search for stations in the entertainment. Hear every NFL game, every NASCAR race, preselected band. college sports and more. The biggest and most compelling names in talk with Howard Stern and Martha Stewart, Select the desired frequency band and then push briefly laugh-out-loud comedy with Jamie Foxx’s The Foxxhole and or button to start the search in and repeatedly the Blue Collar Comedy, plus kids’ programming, world-class or button is pushed the desired direction. If the news, local traffic and weather. All of this with crystal clear, longer, the fast search starts and then stops when the coast-to-coast coverage. Everything worth listening to is button is released. now on SiriusXM. A one-year SiriusXM Satellite Radio subscription is included. SiriusXM and all related marks and I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 199 logos are trademarks of SiriusXM Radio Inc. and its subsidiaries. SiriusXM Radio requires a subscription, sold separately after trial subscription included with vehicle purchase. Prices and programming are provided by SiriusXM and are subject to change. Subscriptions governed by Terms & Conditions available at www.siriusxm.com/ customeragreement. SiriusXM Radio U.S. service only available to those at least 18 years of age in the 48 contiguous United States, D.C., and PR. Service available in Canada; see www.siriusxm.ca. The Program Types available are: All, Pop, Rock, Electronic/Dance, Hip-Hop/R&B, Country, Christian, Jazz/Standards, Classical, Latin/World, Sports, Entertainment, Talk, News, NPR, Comedy, Family & Health, Religion, Traffic/Weather. You can find the SiriusXM current terms and conditions at www.siriusxm.com. Re-Subscribe To SiriusXM Satellite Radio New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio SiriusXM Satellite Radio Program Types with their radio. Following expiration of the free services, Program Types can be selected by pushing the or it will be necessary to access the information on the buttons. The Program Type will change to the next Subscription Information screen in order to re-subscribe. category and the radio will then tune to first station in Press the UP/DOWN button to scroll through the Menu or buttons will tune that program type. Pushing Functions, and the Left/Right button to change the to only the stations in that program type. selected Set-up Menu function. or buttons until #All# is displayed Pushing the will allow normal tuning to all stations. I nf or mat i onPr ovi dedby: 4 200 UNDERSTANDING YOUR INSTRUMENT PANEL Write down the Electronic Serial Number (ESN) for your receiver. To retrieve the Electronic Serial Number of SiriusXM Satellite Receiver Module tune to Channel 0. Make sure that when the order is placed, the ESN are correct. If any of the ESN numbers are not entered correctly, then the SiriusXM subscription will not be able to be transferred to the new radio and will not be active when installed in the customer’s vehicle. To reactivate your service, either call the number listed on the display or visit the provider online. SiriusXM and all related marks and logos are trademarks of SiriusXM Radio Inc. and its subsidiaries. SiriusXM Radio requires a subscription, sold separately after trial subscription included with vehicle purchase. Prices and programming are provided by SiriusXM and are subject to change. Subscriptions governed by Terms & Conditions available at www.siriusxm.com/customeragreement. SiriusXM Radio U.S. service only available to those at least 18 years of age in the 48 contiguous United States, D.C., & PR. www.siriusxm.com. Sirius Subscription Issues When Replacing A Sirius Radio CAUTION! Neither SIRIUS nor FIAT is responsible for any errors in accuracies in the SIRIUS data services or its use in vehicles. When a radio needs to be replaced, the Dealer will need the SIRIUS information to order a new radio (even if the SIRIUS subscription has lapsed). The ESN number contains 12 digits. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 201 The following are instructions for retrieving the Elec- CD Player tronic Serial Number (ESN) from FIAT 500 NAFTA model Introduction radios: This chapter describes the operation of the CD player To retrieve the ESN of SIRIUS Satellite Receiver Module only. To operate the radio, refer to the description in the tune to Channel 0. Make sure that when the order is “Functions and Adjustments” chapter. placed, the ESN are correct. If any of the ESN numbers are not entered correctly, then the SIRIUS subscription CD Player Selection will not be able to be transferred to the new radio and To activate the CD player built into the equipment, will not be active when installed in the customer’s proceed as follows: vehicle. • Load a CD with the equipment switched on. The first Satellite Radio Antenna — If Equipped track will start to play. The antenna for the satellite radio is mounted on the roof Or of the vehicle. Do not place items on the roof around the roof top antenna location. Objects placed within the line • If a CD has already been loaded, turn on the radio and then briefly push the MEDIA button to select the “CD” of sight of the antenna will cause decreased performance. function mode. The last track listened to will start to Larger luggage items should be placed as far from the play. antenna as possible. Do not place items directly on or above the antenna. I nf or mat i onPr ovi dedby: 4 202 UNDERSTANDING YOUR INSTRUMENT PANEL It is advisable to use original CDs to ensure optimal playing. If CD-R/RWs are used, we recommend using good quality media that are burned at the slowest speed possible. Push the button with the radio turned on, to activate the motorized CD ejection system. After ejection, the last audio source listened to before playing the CD will be heard. If the CD is not removed from the radio, it will automatiTo load the CD, insert it gently into the slot to activate the cally be reloaded about 20 seconds later but will not motorized loading system, which will position it cor- resume playing until the #MEDIA# button is pushed to select the CD mode. The radio will switch to the last rectly. source prior to CD mode. The CD can be loaded with the radio off and the ignition key turned to ON/RUN. In this case, the radio will The CD cannot be ejected if the radio is off. remain off. When the radio is turned on, the last source Possible Error Messages listened to before being switched off, will be activated. If the loaded CD cannot be read (e.g. a CD ROM has been When a CD is inserted, the display will show the symbol inserted or the CD is inserted the wrong way or there is “CD” and the wording “CD Reading.” They will remain a reading error) the display shows the wording “CD Disc displayed for the whole time required for the radio to error.” read the CD. When this time has elapsed the radio The CD will then be ejected and the audio source automatically starts playing the first track. activated before the CD mode selection will be heard. CD Loading/Ejecting I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 203 A CD which cannot be read will not be ejected until these functions are over. At the end, with the CD mode activated, the display will show the wording “CD Disc error” for a few seconds and then the CD will be ejected. Display Information If the track has been played for more than 3 seconds, button, starts the track again from the pushing the beginning. In this case, if you want to play the button twice consecuprevious track, push the tively. When the CD player is operating, information will ap- Track Fast Forward/Rewind pear on the display with the following meaning: Keep the button pushed down to fast forward the button pushed down to selected track and keep the • “Track 5” indicates the CD track number. fast rewind the track. The fast forward/rewind will • “03:42” indicates the time elapsed since the start of the stop once the button is released. track (if the relevant Menu function is activated). Pause Function Track Selection To pause the CD player, push the button. The word- Briefly push the button to play the previous CD ing “CD Pause” appears on the display. button to play the next track. The track and the To resume listening to the track, push the tracks are selected cyclically: the first track is selected again. after the last track and vice versa. I nf or mat i onPr ovi dedby: button 4 204 UNDERSTANDING YOUR INSTRUMENT PANEL The specifications and operating conditions for playing MP3 files are the following: CD MP3 Player Introduction This chapter describes the operation of the CD MP3 player. NOTE: Layer-3 audio decoding technology is licensed from Fraunhofer IIS and Thomson multimedia. MP3 Mode In addition to playing regular audio CDs, the radio is also enabled to play CDROMs on which compressed audio files have been recorded in an MP3 format. • The CD-ROMs used should be burned in accordance with ISO standard 9660. • The music files should have the extension “.mp3” or “.wma” files with a different extension will not be reproduced. • The sampling frequencies that can be reproduced are: 44.1 kHz, stereo (from 96 to 320 kbit/s) – 22.05 kHz, mono or stereo (from 32 to 80 kbit/s). • Tracks with a variable bit-rate can be reproduced. To guarantee optimal reproduction, it is advisable to use good quality CDs burned at the lowest speed possible. NOTE: The track names must not include the following characters: spaces, ‘ (apostrophes), ( and ) (open and close The files on an MP3 CD are structured in folders that brackets). During the burning of a MP3 CD, make sure create lists of all the folders containing MP3 tracks that the names of the files do not contain these characters; (folders or subfolders are all on the same level). The if not, the radio will not be able to play the tracks folders that do not contain MP3 tracks cannot be selected. involved. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 205 When one of the ID3-TAG pieces of information is chosen to be displayed (Title, Artist, Album) and this informaIf a hybrid disc is inserted (Mixed Mode, Enhanced, tion has not been recorded for the track played, the text CD-Extra) also containing MP3 files, the radio automati#UNKNOWN# will be displayed for that field. cally starts playing the audio session. It is possible to move to the MP3 session while playing by keeping the Selection Of Next/Previous Folder CD button pressed for more than two seconds. Push the button to select a next folder or the button to select the previous folder. The display NOTE: When the function is activated the radio may take a few seconds to start playing. While checking the disc will show the number of the folder. the display will show “CD Reading.” If no MP3 files are The folders are selected cyclically. The first folder is detected, the radio will resume playing the audio session selected after the last folder and vice versa. from the point where it was interrupted. If no other folder/track is selected in the next two Display Information seconds, the first track on the new folder will be played. ID3–Tag Information Display After the last track in a folder is played, the next folder In addition to the information relating to the time will be played. elapsed, folder name and file name, the radio is also capable of displaying ID3–TAG information relating to Title Track, Artist and Author. Selecting MP3 Sessions With Hybrid Discs I nf or mat i onPr ovi dedby: 4 206 UNDERSTANDING YOUR INSTRUMENT PANEL Structure Of The Folders Source Can Not Be Selected The radio with MP3 player: Nothing has been loaded. Load the CD or the MP3 CD to be listened to. • Recognizes only the folders that effectively contain MP3 format files. CD Player • If the MP3 files on a CD-ROM are structured in The CD Does Not Play: sub-folders their structure is compressed to a single The CD is dirty. Clean the CD. level structure, where the sub-folders are taken to the The CD is scratched. Try using another CD. level of the main folders. The CD Can Not Be Loaded: Troubleshooting General Sound Volume Low A CD is already loaded. Press the the CD. button and remove MP3 File Reading The Fader function should be adjusted to the values “F” Track Skips While Playing Mp3 Files: (front) only to prevent the reduction in radio output power and the cancelling of the volume if the Fader level The CD is scratched or dirty. adjustment is equal to R+9. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 207 The Duration Of The Mp3 Tracks Is Not Correctly Displayed: In some cases (due to the recording mode) the duration of the MP3 tracks can be displayed incorrectly. Operating Instructions — Hands-Free Phone Refer to the appropriate “BLUE&ME™ User’s Manual” for further information. 4 Personal/Portable Navigation Device (PND) A Personal/Portable Navigation Device (PND) is available as optional equipment for this vehicle, refer to the Navigation User Guide for further information. iPod®/USB/MEDIA PLAYER CONTROL — IF EQUIPPED USB/AUX Port 1 — AUXiliary Cable Jack 2 — USB Connector This feature allows an iPod® or external USB device to be Refer to the appropriate Blue&Me™ radio User’s Manual plugged into the USB or AUX port, located in the center for iPod® or external USB device support capability. console. I nf or mat i onPr ovi dedby: 208 UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand control is a rocker-type switch with a The remote sound system controls are located on the rear pushbutton in the center and controls the volume and surface of the steering wheel. Reach behind the wheel to mode of the sound system. Pushing the top of the rocker switch will increase the volume, and pushing the bottom access the switches. of the rocker switch will decrease the volume. STEERING WHEEL AUDIO CONTROLS Pushing the center button will make the radio switch between the various modes available (AM/FM/SAT/ CD/AUX/Media Player, etc.) and can also be used to select/enter an item while scrolling through menu. The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The following describes the left-hand control operation in each mode. Remote Sound System Controls (Back View Of Steering Wheel) I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 209 Radio Operation Operating Instructions — Hands-Free Phone (If Equipped) Pushing the top of the switch will “Seek” up for the next listenable station and pushing the bottom of the switch Refer to the appropriate Blue&Me™ User’s Manual for further information. will “Seek” down for the next listenable station. The button located in the center of the left-hand control CD/DVD DISC MAINTENANCE will tune to the next preset station that you have proTo keep a CD/DVD in good condition, take the following grammed in the radio preset button. precautions: CD Player Operation 1. Handle the disc by its edge; avoid touching the Pushing the top of the switch once will go to the next surface. track on the CD. Pushing the bottom of the switch once will go to the beginning of the current track, or to the 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. beginning of the previous track if it is within one second after the current track begins to play. 3. Do not apply paper or tape to the disc; avoid scratchIf you push the switch up or down twice, it plays the second track; three times, it will play the third, etc. ing the disc. I nf or mat i onPr ovi dedby: 4 210 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Do not use solvents such as benzene, thinner, cleaners, RADIO OPERATION AND MOBILE PHONES or anti-static sprays. Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from 5. Store the disc in its case after playing. your radio. This condition may be lessened or eliminated 6. Do not expose the disc to direct sunlight. by relocating the mobile phone antenna. This condition is 7. Do not store the disc where temperatures may become not harmful to the radio. If your radio performance does not satisfactorily “clear” by the repositioning of the too high. antenna, it is recommended that the radio volume be NOTE: If you experience difficulty in playing a particular turned down or off during mobile phone operation. disc, it may be damaged (e.g., scratched, reflective coating removed, a hair, moisture or dew on the disc) CLIMATE CONTROLS oversized, or have protection encoding. Try a known The air conditioning and heating system is designed to good disc before considering disc player service. make you comfortable in all types of weather. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 211 Manual Heating And Air Conditioning 1. Temperature Control Rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the scale indicates cooler temperatures, while rotating to the right into the red area indicates warmer temperatures. 2. Blower Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “0” (OFF) position. There are four blower speeds. 3. Recirculation Control Manual Temperature Control (MTC) Rotate this control to change the system between recirThe Manual Climate controls consist of a series of rotary culation mode and outside air mode. Recirculation can be dials and one inner push knob. used when outside conditions such as smoke, odors, dust, or high humidity are present. I nf or mat i onPr ovi dedby: 4 212 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. • The use of the Recirculation mode in cold or damp NOTE: The center instrument panel outlets can be aimed weather could cause windows to fog on the inside, so that they are directed toward the rear seat passengers because of moisture buildup inside the vehicle. Se- for maximum airflow to the rear. • Bi-Level lect the outside air position for maximum defogging. Air is directed through the panel and floor • Recirculation can be used in all modes except for outlets. Defrost. • Floor • The A/C can be deselected manually without disAir is directed through the floor outlets with a turbing the mode control selection. small amount flowing through the defrost and side window demister outlets. 4. Mode Control • Mix Rotate this control to change the system between Modes Air is directed through the floor, defrost, and (Panel, Bi-Level, Floor, Mix, Defrost). side window demister outlets. This setting works best in cold or snowy conditions that I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 213 require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. • Defrost Air is directed through the windshield and side window demister outlets. Use this mode with maximum blower and temperature settings for best windshield and side window defrosting. MAX A/C For maximum cooling, use the A/C and recirculation modes at the same time. ECONOMY MODE If economy mode is desired, push the A/C button to turn OFF the indicator light and the A/C compressor. Then, move the temperature control to the desired temperature. NOTE: The air conditioning compressor operates in Mix Automatic Temperature Control (ATC) or Defrost, even if the Air Conditioning (A/C) button is • The Automatic Temperature Control (ATC) allows the not pushed. This dehumidifies the air to help dry the occupant to select a comfort settings. windshield. To improve fuel economy, use these modes only when necessary. • The system provides set-and-forget operation for optimum comfort and convenience. 5. A/C Button Push this button to engage the Air Conditioning. A light • The system can be controlled manually, if desired. will illuminate when the Air Conditioning system is engaged. I nf or mat i onPr ovi dedby: 4 214 UNDERSTANDING YOUR INSTRUMENT PANEL The ATC system automatically maintains the interior between manual mode and automatic modes. Refer to comfort level desired by the occupant. “Automatic Operation” for more information. 2. A/C Button Push and release to change the current Air Conditioning (A/C) setting. Performing this function will cause the ATC to switch into manual mode. 3. Temperature Control Up Button Provides temperature up control. Push the button for warmer temperature settings. 4. Blower Control Up/Down Buttons There are 12 fixed blower speeds. The blower control up/down buttons regulate the amount of air forced Automatic Temperature Control (ATC) through the system in any mode you select. The blower 1. AUTO Temperature Control (ATC) Button speed increases as you push, or hold, the blower control Controls airflow, temperature, distribution, and air recir- up button and decreases when you push, or hold, the culation automatically. Push and release to select. Per- blower control down button. forming this function will cause the ATC to switch I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 215 The blower fan speed may be set to any fixed speed by 6. Front Defrost pushing the blower control up or down buttons. The fan Push and release to change the current airflow will now operate at a fixed speed until additional speeds setting to Defrost mode. The indicator illuminates are selected. This allows the front occupants to control when this feature is ON. Air comes from the windshield the volume of air circulated in the vehicle and cancel the and side window demist outlets. When the defrost butAUTO mode. ton is selected, the blower level will increase. Use Defrost The operator can also select the direction of the airflow mode with maximum temperature settings for best windby selecting one of the following positions. shield and side window defrosting and defogging. Performing this function will cause the ATC to switch into 5. Mix Mode manual mode. If the front defrost mode is turned off the Air is directed through the floor, defrost, and side climate system will return the previous setting. window demister outlets. This setting works best 7. Floor Mode in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort Air is directed through the floor outlets with a while reducing moisture on the windshield. Performing small amount flowing through the defrost and this function will cause the ATC to switch into manual side window demister outlets. Performing this function mode. will cause the ATC to switch into manual mode. I nf or mat i onPr ovi dedby: 4 216 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Panel Mode 10. Temperature Control Down Button Air is directed through the outlets in the instru- Provides temperature down control. Push the button for ment panel. These outlets can be adjusted to direct cooler temperature settings. airflow. Performing this function will cause the ATC to NOTE: If the temperature is lowered until #Lo# is disswitch into manual mode. played, all high voltage Heating, Ventilation, and Air NOTE: The center instrument panel outlets can be aimed Conditioning (HVAC) systems are deactivated and amso that they are directed toward the rear seat passengers bient air is circulated according to the Heating, Ventilafor maximum airflow to the rear. tion, and Air Conditioning (HVAC) control settings. 9. Bi-Level 11. Climate Control ON/OFF Button Air is directed through the panel and floor outlets. Press and release the Panel mode button and Floor mode button to enter Bi-Level mode, the indicators illuminate when ON. Performing this function will cause the ATC to switch into manual mode. Push and release to turn the Climate Control ON or OFF. 12. Recirculation Control Button Push and release to change the current setting. The indicator illuminates when ON. NOTE: When in Defrost mode, the Recirculation button will flash if pushed. This indicates that you can not proceed to this mode due to fogging risk. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 217 Climate Control Functions Recirculation Control Air Conditioning (A/C) When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by pushing the RECIRCULATION control button. Recirculation mode should only be used temporarily. The recirculation LED will illuminate when this button is selected. Push the button a second time to turn off the Recirculation mode LED and allow outside air into the vehicle. The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system. When in A/C mode with the ATC set to a cool temperature, dehumidified air flows through the air outlets. If Economy mode is desired, push the A/C button to turn off the A/C mode in the ATC display and deactivate the A/C system. NOTE: • If the system is in Mix or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows. • If fog or mist appears on the windshield or side glass, select Defrost mode and adjust blower speed if needed. NOTE: In cold weather, use of Recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (indicator light shall blink) if conditions exist that could create fogging on the inside of the windshield. On systems with Manual Climate Controls, the Recirculation mode is not allowed in Defrost mode to improve window clearing operation. Recirculation will be disabled automatically if this mode is selected. Attempting to use Recirculation while in this mode will cause the LED in the control button to blink and then turn off. I nf or mat i onPr ovi dedby: 4 218 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Operation NOTE: 1. Push the AUTO button on the Automatic Temperature • It is not necessary to move the temperature settings for Control (ATC) Panel, the indicator will illuminate cold or hot vehicles. The system automatically adjusts when on. the temperature, mode and fan speed to provide comfort as quickly as possible. 2. Next, adjust the temperature you would like the system to maintain by adjusting the temperature con- • The temperature can be displayed in U.S. or Metric trol buttons. Once the desired temperature is disunits by selecting the US/M customer-programmable played, the system will achieve and automatically feature. Refer to the “Electronic Vehicle Information maintain that comfort level. Center (EVIC) — Customer-Programmable Features” in this section of the manual. 3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 219 Manual Operation Window Fogging The system allows for manual selection of blower speed, Windows will fog on the inside when the humidity inside air distribution mode, A/C status and recirculation con- the vehicle is high. This often occurs in mild or cool trol. temperatures when it’s rainy or humid. In most cases, turning the air conditioning (pressing the A/C button) on The blower fan speed can be set to any fixed speed by will clear the fog. Adjust the temperature control, air adjusting the blower control. The fan will now operate at direction, and blower speed to maintain comfort. a fixed speed until additional speeds are selected. This allows the front occupants to control the volume of air As the temperature gets colder, it may be necessary to circulated in the vehicle and cancel the Auto mode. direct air onto the windshield. Adjust the temperature control and blower speed to maintain comfort. Higher The operator can also select the direction of the airflow blower speeds will reduce fogging. Interior fogging on by selecting one of the available mode settings. A/C the windshield can be quickly removed by selecting the operation and Recirculation control can also be manually Defrost mode. selected in Manual operation. Regular cleaning of the inside of the windows with a Operating Tips non-filming cleaning solution (vinegar and water works NOTE: Refer to the chart at the end of this section for very well) will help prevent contaminates (cigarette suggested control settings for various weather condi- smoke, perfumes, etc.) from sticking to the windows. tions. Contaminates increase the rate of window fogging. I nf or mat i onPr ovi dedby: 4 220 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Automatic Temperature Controls (ATC) will automatically adjust the climate control settings to reduce or eliminate window fogging on the front windshield. When this occurs, recirculation will be unavailable. Summer Operation NOTE: In some cases during high temperature operation, the air conditioning system performance may be reduced. This is to help protect the engine from overheating during the high load condition. Your air conditioning system is also equipped with an automatic recirculation system. When the system senses a heavy load or high heat conditions, it may use Recirculation A/C mode to provide additional comfort while in automatic mode. Winter Operation When operating the system during the winter months, make sure the air intake, located directly in front of the windshield, is free of ice, slush, snow, or other obstructions. Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air using the high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the air conditioning system is started again. I nf or mat i onPr ovi dedby: UNDERSTANDING YOUR INSTRUMENT PANEL 221 Operating Tips Chart 4 I nf or mat i onPr ovi dedby: I nf or mat i onPr ovi dedby: STARTING AND OPERATING CONTENTS ! STARTING PROCEDURES . . . . . . . . . . . . . . . .227 ▫ Five-Speed Manual Transmission. . . . . . . . . . .230 ▫ Manual Transmission — If Equipped . . . . . . .227 ▫ Recommended Shift Speeds . . . . . . . . . . . . . .232 ▫ Automatic Transmission — If Equipped . . . . .227 ▫ Downshifting . . . . . . . . . . . . . . . . . . . . . . . .233 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .228 ! AUTOMATIC TRANSMISSION — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . ▫ Cold Weather Operation . . . . . . . . . . . . . . . .228 ▫ Key Ignition Park Interlock. . . . . . . . . . . . ▫ Extended Park Starting. . . . . . . . . . . . . . . . . .228 ▫ Brake/Transmission Shift Interlock System ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . .229 ▫ Six-Speed Automatic Transmission . . . . . . ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . .230 ▫ Gear Ranges . . . . . . . . . . . . . . . . . . . . . . ▫ Turbocharger “Cool Down” . . . . . . . . . . . . . .230 ! AUTOSTICK . . . . . . . . . . . . . . . . . . . . . . . ! MANUAL TRANSMISSION — IF EQUIPPED . .230 I nf or mat i onPr ovi dedby: 5 . . .233 . . .235 . . .235 . . .235 . . .237 . . .242 224 STARTING AND OPERATING ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .242 ! ELECTRONIC BRAKE CONTROL SYSTEM . . . .252 ! DRIVING ON SLIPPERY SURFACES . . . . . . . . .244 ▫ Four-Wheel Anti-Lock Brake System (ABS) . . .252 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . .244 ▫ Brake Assist System (BAS) . . . . . . . . . . . . . . .254 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .244 ▫ Traction Control System (TCS) . . . . . . . . . . . .255 ! DRIVING THROUGH WATER . . . . . . . . . . . . .245 ▫ Hill Start Assist (HSA) . . . . . . . . . . . . . . . . .255 ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . .245 ▫ Electronic Stability Control (ESC) . . . . . . . . . .257 ▫ Shallow Standing Water . . . . . . . . . . . . . . . . .245 ▫ ESC Activation/Malfunction Indicator Light And ESC OFF Indicator Light . . . . . . . . . . . .260 ! POWER STEERING . . . . . . . . . . . . . . . . . . . . .247 ! PARKING BRAKE . . . . . . . . . . . . . . . . . . . . . .248 ! SPORT MODE . . . . . . . . . . . . . . . . . . . . . . . . .250 ▫ Manual Transmission — If Equipped . . . . . . . .250 ▫ Automatic Transmission — If Equipped . . . . . .251 ! BRAKE SYSTEM . . . . . . . . . . . . . . . . . . . . . . .252 ! TIRE SAFETY INFORMATION . . . . . . . . . . . . .261 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . .261 ▫ Tire Identification Number (TIN). . . . . . . . . . .265 ▫ Tire Terminology And Definitions . . . . . . . . . .266 ▫ Tire Loading And Tire Pressure . . . . . . . . . . .268 I nf or mat i onPr ovi dedby: STARTING AND OPERATING 225 ! TIRES — GENERAL INFORMATION . . . . . . . .273 ! TIRE ROTATION RECOMMENDATIONS . . . . .287 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . .273 ! TIRE PRESSURE MONITORING SYSTEM (TPMS) . . . . . . . . . . . . . . . . ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . .275 ▫ Base System . . . . . . . . . . . . . . . . . . ▫ Tire Pressures For High Speed Operation . . . .276 ▫ Enhanced System — If Equipped . . . ▫ Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . .276 ▫ Premium TPM System . . . . . . . . . . . ▫ Tire Types . . . . . . . . . . . . . . . . . . . . . . . . . . .277 ▫ General Information . . . . . . . . . . . . ▫ Run Flat Tires — If Equipped . . . . . . . . . . . . .279 ! FUEL REQUIREMENTS — 1.4L Engine ▫ Spare Tires — If Equipped . . . . . . . . . . . . . . .279 ! FUEL REQUIREMENTS — 1.4L Turbo . ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . .282 ▫ Reformulated Gasoline . . . . . . . . . . ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . .283 ▫ Gasoline/Oxygenate Blends . . . . . . . ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . .283 ▫ E-85 Usage In Non-Flex Fuel Vehicles ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . .284 ▫ MMT In Gasoline . . . . . . . . . . . . . . ! TIRE CHAINS (TRACTION DEVICES) . . . . . . .286 I nf or mat i onPr ovi dedby: . . . . . . .288 . . . . . . .291 . . . . . . .294 . . . . . . .294 . . . . . . .298 . . . . . . .298 . . . . . . .299 . . . . . . .299 . . . . . . .300 . . . . . . .300 . . . . . . .301 5 226 STARTING AND OPERATING ▫ Materials Added To Fuel . . . . . . . . . . . . . . . .301 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .305 ▫ Fuel System Cautions. . . . . . . . . . . . . . . . . . .302 ! TRAILER TOWING . . . . . . . . . . . . . . . . . . . . .305 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . .303 ! RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) . . . . . . . . . . . . . . . . . . .306 ! ADDING FUEL . . . . . . . . . . . . . . . . . . . . . . . .303 ▫ Towing This Vehicle Behind Another Vehicle . .306 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . .303 I nf or mat i onPr ovi dedby: STARTING AND OPERATING 227 STARTING PROCEDURES Manual Transmission — If Equipped Before starting your vehicle, adjust your seat, adjust both Apply the parking brake, place the shift lever in NEUinside and outside mirrors, and fasten your seat belts. TRAL, and press the clutch pedal before starting the vehicle. This vehicle is equipped with a clutch interlocking ignition system. It will not start unless the clutch WARNING! pedal is pressed to the floor. • Never leave children alone in a vehicle, or with Automatic Transmission — If Equipped access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is The shift lever must be in the PARK or NEUTRAL dangerous for a number of reasons. A child or position before you can start the engine. Depress the others could be seriously or fatally injured. Chil- brake pedal before shifting to any driving gear. dren should be warned not to touch the parking NOTE: You must press the brake pedal before shifting brake, brake pedal or the shift lever. • Do not leave the Key Fob in or near the vehicle (or out of PARK. in a location accessible to children). A child could operate power windows, other controls, or move the vehicle. I nf or mat i onPr ovi dedby: 5 228 STARTING AND OPERATING The message “plug in engine heater” will be displayed in the instrument cluster when the ambient temperature is NOTE: Normal starting of either a cold or a warm below 5° F (–15° C) at the time the engine is shut off as a engine is obtained without pumping or pressing the reminder to avoid possible crank delays at the next cold accelerator pedal. start. Turn the ignition switch to the AVV/ACC (START) position and release it when the engine starts. If the CAUTION! engine fails to start within 10 seconds, turn the ignition switch to the STOP (OFF/LOCK) position, wait 10 to 15 Use of the recommended oil and adhering to the prescribed oil change intervals is important to preseconds, then repeat the “Normal Starting” procedure. vent engine damage and ensure satisfactory starting Cold Weather Operation in cold conditions. To prevent possible engine damage while starting at low temperatures, this vehicle will inhibit engine cranking Extended Park Starting when the ambient temperature is less than –22° F (–30° C) NOTE: Extended Park condition occurs when the vehicle and the oil temperature sensor reading indicates an has not been started or driven for at least 35 days. engine block heater has not been used. An externallypowered electric engine block heater is available as 1. Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle. optional equipment or from your authorized dealer. Normal Starting I nf or mat i onPr ovi dedby: STARTING AND OPERATING 229 2. Cycle the ignition in the START position and release it If Engine Fails To Start when the engine starts. 3. If the engine fails to start within ten seconds, cycle the ignition to the STOP (OFF/LOCK) position, wait five seconds to allow the starter to cool, then repeat the Extended Park Starting procedure. 4. If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure. CAUTION! To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time. Wait 10 to 15 seconds before trying again. WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. CAUTION! 5 • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. (Continued) I nf or mat i onPr ovi dedby: 230 STARTING AND OPERATING MANUAL TRANSMISSION — IF EQUIPPED CAUTION! (Continued) • To prevent damage to the starter, do not continuously crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After Starting The idle speed is controlled automatically and it will decrease as the engine warms up. Turbocharger “Cool Down” Five-Speed Manual Transmission WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should always be applied when the driver is not in the vehicle, especially on an incline. This vehicle is equipped with an after-run pump to cool the turbocharger after the engine is shut off. Depending on the type of driving and the amount of cargo, the pump will run for up to 10 minutes after the engine has been shut off to circulate coolant through the turbocharger. Although the pump is rubber-mounted for quiet operation, it is normal to hear it running during this time. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 231 Use each gear in numerical order; do not skip a gear. Be sure the transmission is in first gear, not third, when starting from a standing position. Damage to the clutch can result from starting in third gear. For most city driving, you will find it easier to use only the lower gears. For steady highway driving with light accelerations, fifth gear is recommended. Never drive with your foot resting on the clutch pedal, and never try to hold the vehicle on a hill with the clutch pedal partially engaged. This will cause abnormal wear on the clutch. Shift Lever REVERSE gear is not synchronized and the vehicle must Fully press the clutch pedal before you shift gears. As you be at a complete stop to shift into REVERSE gear. When release the clutch pedal, lightly press the accelerator selecting REVERSE gear, the driver should pause (appedal. proximately 2 seconds) after pushing in the clutch pedal NOTE: To shift into REVERSE from NEUTRAL, lift the and prior to shifting into REVERSE which allows gears to ring under the knob and, at the same time move the stop spinning. Should an unwanted clash noise be produced, the pause length should be increased. gearshift lever to the right and then backward. I nf or mat i onPr ovi dedby: 5 232 STARTING AND OPERATING NOTE: Recommended Shift Speeds • Clashing REVERSE gear, especially if vehicle is mov- To use your manual transmission for optimal fuel economy, it should be upshifted as listed in the following ing, can result in transmission damage. table. • During cold weather, until the transmission lubricant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the transmission. Engine Size 1.4L/1.4L Turbo Engine Manual Transmission Recommended Shift Speeds Units In mph (km/h) Acceleration 1 to 2 2 to 3 3 to 4 Rate Accel 14 23 29 (23) (37) (47) Cruise 12 18 25 (19) (29) (40) I nf or mat i onPr ovi dedby: 4 to 5 38 (61) 32 (52) STARTING AND OPERATING 233 Downshifting AUTOMATIC TRANSMISSION — IF EQUIPPED Proper downshifting will improve fuel economy and prolong engine life. CAUTION! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage to the clutch and the transmission can result from skipping a gear while downshifting or downshifting at too high of a vehicle speed even if the clutch pedal is held pressed (i.e., not released). CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into or out of PARK or REVERSE only after the vehicle has come to a complete stop. • Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly pressing the brake pedal. NOTE: You must press and hold the brake pedal while To maintain a safe speed and prolong brake life, shift down shifting out of PARK. to second or first gear when descending a steep grade. When turning a corner or driving up a steep grade, downshift early so that the engine will not be overburdened. I nf or mat i onPr ovi dedby: 5 234 STARTING AND OPERATING WARNING! WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal. • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the ignition key. Once the key is removed, the transmission is locked in PARK, securing the vehicle against unwanted movement. • When leaving the vehicle, always remove the ignition key from the vehicle and lock the vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector. • Do not leave the ignition key in or near the vehicle (or in a location accessible to children). A child could operate power windows, other controls, or move the vehicle. (Continued) I nf or mat i onPr ovi dedby: STARTING AND OPERATING 235 Key Ignition Park Interlock Six-Speed Automatic Transmission This vehicle is equipped with a Key Ignition Park Interlock which requires the transmission to be in PARK before the ignition switch can be turned to the LOCK/ OFF (key removal) position. The key can only be removed from the ignition when the ignition is in the LOCK/OFF position, and once removed, the transmission is locked in PARK. The transmission gear position display (located in the instrument cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of PARK (Refer to “Brake/Transmission Shift Interlock System” in this section). To drive, move the shift lever from PARK or NEUTRAL to the DRIVE position. The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new This vehicle is equipped with a Brake Transmission Shift vehicle may be somewhat abrupt. This is a normal Interlock System (BTSI) that holds the shift lever in PARK condition, and precision shifts will develop within a few unless the brakes are applied. To shift the transmission hundred miles (kilometers). out of PARK, the ignition switch must be turned to the ON/RUN position (engine running or not) and the brake pedal must be pressed. Brake/Transmission Shift Interlock System I nf or mat i onPr ovi dedby: 5 236 STARTING AND OPERATING The transmission shift lever has PARK, REVERSE, NEUTRAL, DRIVE, and AutoStick shift positions. Manual shifts can be made using the AutoStick shift control (refer to “AutoStick” in this section for further information). Toggling the shift lever forward (-) or rearward (+) while in the AutoStick position (beside the DRIVE position) will manually select the transmission gear, and will display the current gear in the instrument cluster as 1, 2, 3, etc. NOTE: If the shift lever cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward) it is probably in the AutoStick (+/-) position Shift Lever (beside the DRIVE position). In AutoStick mode, the Only shift from DRIVE to PARK or REVERSE when the transmission gear (1, 2, 3, etc.) is displayed in the accelerator pedal is released and the vehicle is stopped. instrument cluster. Move the shift lever to the right (into Be sure to keep your foot on the brake pedal when the DRIVE [D] position) for access to PARK, REVERSE, shifting between these gears. and NEUTRAL. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 237 When parking on a hill, apply the parking brake before DO NOT race the engine when shifting from PARK or shifting the transmission to PARK, otherwise the load on the transmission locking mechanism may make it difficult to NEUTRAL into another gear range. move the shift lever out of PARK. As an added precaution, NOTE: After selecting any gear range, wait a moment to turn the front wheels toward the curb on a downhill grade allow the selected gear to engage before accelerating. and away from the curb on an uphill grade. This is especially important when the engine is cold. Gear Ranges WARNING! PARK (P) This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. When parking on a level surface, you may shift the transmission into PARK first, and then apply the parking brake. • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever out of PARK with the brake pedal released. Make sure the transmission is in PARK before leaving the vehicle. (Continued) I nf or mat i onPr ovi dedby: 5 238 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal. • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the ignition key. Once the key is removed, the transmission is locked in PARK, securing the vehicle against unwanted movement. • When leaving the vehicle, always remove the ignition key from the vehicle and lock the vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Do not leave the ignition key in or near the vehicle (or in a location accessible to children). A child could operate power windows, other controls, or move the vehicle. (Continued) I nf or mat i onPr ovi dedby: STARTING AND OPERATING 239 CAUTION! • Look at the transmission gear position display and verify that it indicates the PARK position. • Before moving the shift lever out of PARK, you must turn the ignition switch from the LOCK/OFF position to the ON/RUN position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain. • With brake pedal released, verify that the shift lever will not move out of PARK. REVERSE (R) This range is for moving the vehicle backward. Shift into REVERSE only after the vehicle has come to a complete stop. NEUTRAL (N) The following indicators should be used to ensure that Use this range when the vehicle is standing for prolonged you have engaged the transmission into the PARK posiperiods with the engine running. The engine may be tion: started in this range. Apply the parking brake and shift • When shifting into PARK, press the lock button on the the transmission into PARK if you must leave the vehicle. shift lever and firmly move the lever all the way forward and to the left until it stops and is fully seated. I nf or mat i onPr ovi dedby: 5 240 STARTING AND OPERATING DRIVE (D) WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage. Refer to “Recreational Towing” in “Starting And Operating” and “Towing A Disabled Vehicle” in “What To Do In Emergencies” for further information. This range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts, and the best fuel economy. The transmission automatically upshifts through all forward gears. The DRIVE position provides optimum driving characteristics under all normal operating conditions. When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, or traveling into strong head winds), use the AutoStick shift control (refer to AutoStick in this section for further information) to select a lower gear. Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat buildup. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 241 If the transmission temperature exceeds normal operating limits, the transmission controller will expand the range of torque converter clutch engagement. This is done to prevent transmission damage due to overheating. Limp Home Mode allows the vehicle to be driven to an authorized dealer for service without damaging the transmission. In the event of a momentary problem, the transmission During cold temperatures, transmission operation may can be reset to regain all forward gears by performing the be modified depending on engine coolant temperature. following steps: Normal operation will resume once the engine tempera- 1. Stop the vehicle. ture has risen to a suitable level. 2. Shift the transmission into PARK. Transmission Limp Home Mode 3. Turn the ignition switch to the OFF position. Transmission function is monitored electronically for abnormal conditions. If a condition is detected that could 4. Wait approximately 10 seconds. result in transmission damage, Transmission Limp Home Mode is activated. In this mode, the transmission remains 5. Restart the engine. in third gear regardless of which forward gear is selected. 6. Shift into the desired gear range. If the problem is no PARK, REVERSE, and NEUTRAL will continue to operate. longer detected, the transmission will return to normal The Malfunction Indicator Light (MIL) may be illuminated. operation. I nf or mat i onPr ovi dedby: 5 242 STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. Operation When the shift lever is in the AutoStick position (beside the Drive position), it can be moved forward and rearward. This allows the driver to manually select the transmission gear being used. Moving the shift lever If the transmission cannot be reset, authorized dealer forward (-) triggers a downshift, and rearward (+) an upshift. The current gear is displayed in the instrument service is required. cluster. AUTOSTICK NOTE: In AutoStick mode, the transmission will only AutoStick is a driver-interactive transmission feature shift up or down when the driver moves the shift lever providing manual shift control, giving you more control rearward (+) or forward (-), except as described below. of the vehicle. AutoStick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, • The transmission will automatically upshift when necessary to prevent engine over-speed. and improve overall vehicle performance. This system can also provide you with more control during passing, • The transmission will automatically downshift as the city driving, cold slippery conditions, mountain driving, vehicle slows (to prevent engine lugging) and will and many other situations. display the current gear. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 243 • The transmission will automatically downshift to first • Transmission shifting will be more noticeable when gear when coming to a stop. After a stop, the driver AutoStick is engaged. should manually upshift (+) the transmission as the • The system may revert to automatic shift mode if a vehicle is accelerated. fault or overheat condition is detected. • You can start out (from a stop) in first, second, or third To disengage AutoStick mode, return the shift lever to the gear. Starting out in second or third gear can be helpful DRIVE position. You can shift in or out of the AutoStick in snow or icy conditions. To select second or third position at any time without taking your foot off the gear after the vehicle is brought to a stop, tap the shift accelerator pedal. lever rearward (+) once or twice. • The system will ignore shift commands that would cause engine lugging or overspeed. An audible beep will sound if an inappropriate gear is requested. • Avoid using speed control when AutoStick is engaged because the transmission will not shift automatically. WARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. I nf or mat i onPr ovi dedby: 5 244 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Traction Acceleration When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the driving wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have a collision. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.). 1. Slow down during rainstorms or when the roads are slushy. 2. Slow down if the road has standing water or puddles. 3. Replace the tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 245 DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Cautions safety and prevent damage to your vehicle. and Warnings before doing so. Flowing/Rising Water WARNING! WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly. Failure to follow this warning may result in injuries that are serious or fatal to you, your passengers, and others around you. • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes. • Failure to follow these warnings may result in injuries that are serious or fatal to you, your passengers, and others around you. I nf or mat i onPr ovi dedby: 5 246 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • Do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects. • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage. Such damage is not covered by the New Vehicle Limited Warranty. • Getting water inside your vehicle’s engine can cause it to lock up and stall out, and cause serious internal damage to the engine. Such damage is not covered by the New Vehicle Limited Warranty. (Continued) I nf or mat i onPr ovi dedby: STARTING AND OPERATING 247 POWER STEERING The electric power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will vary its assist to provide light efforts while parking and good feel while driving. If the electric steering system experiences a fault that prevents it from providing assist, you will still have the ability to steer the vehicle manually. If the Steering icon is displayed and the “SERVICE POWER STEERING” message is displayed on the EVIC screen, they indicate that extreme steering maneuvers may have occurred which caused an over temperature condition in the power steering system. Once driving conditions are safe, pull over and let the vehicle idle for a few moments until the icon and message turn off. Refer to “Electronic Vehicle Information (EVIC)” in “Understanding Your Instrument Panel” for further information. WARNING! If the Steering icon, and the #SERVICE POWER STEERING - ASSIST OFF# message is displayed on the EVIC Continued operation with reduced or no power steer- screen, the vehicle needs to be taken to an authorized ing assist could pose a safety risk to yourself and dealer for service. Refer to “Electronic Vehicle Informaothers. Service should be obtained as soon as possible. tion (EVIC)” in “Understanding Your Instrument Panel” If the Steering icon is flashing, it indicates that the vehicle for further information. needs to be taken to an authorized dealer for service. It is likely the vehicle has lost power steering assistance. I nf or mat i onPr ovi dedby: 5 248 STARTING AND OPERATING NOTE: • Even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at low speeds and during parking maneuvers. • If the condition persists, see your authorized dealer for service. PARKING BRAKE Before leaving the vehicle, make sure that the parking Parking Brake brake is fully applied. Also, be certain to leave the When the parking brake is applied with the ignition manual transmission in REVERSE or first gear. switch in the MAR (ACC/ON/RUN) position, the Brake The parking brake lever is located in the center console. Warning Light in the instrument cluster will illuminate. To apply the parking brake, pull the lever up as firmly as possible. To release the parking brake, pull the lever up slightly, press the center button, then lower the lever completely. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 249 When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. WARNING! (Continued) • Do not leave the Key Fob in or near the vehicle or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave a manual transmission in REVERSE or first (1st) gear. Failure to do so may allow the vehicle to roll and cause damage or injury. (Continued) I nf or mat i onPr ovi dedby: 5 250 STARTING AND OPERATING CAUTION! If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. SPORT MODE Manual Transmission — If Equipped The Sport mode increases steering feedback to the driver with slight increases in effort and throttle pedal-to-engine SPORT Button response. This driving mode is useful while driving on twisty roads where more steering precision is desired in Once activated, a SPORT message will be displayed in the instrument cluster. spirited cornering. 1. To activate the Sport mode, press the SPORT button. 2. Momentarily release the accelerator pedal. 3. Press the accelerator pedal again to activate. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 251 Automatic Transmission — If Equipped The Sport mode increases steering feedback to the driver with slight increase in effort and changes the transmission shift schedules for more aggressive shifting. This driving mode is useful while driving on twisty roads where more steering precision is desired in spirited cornering. 1. To activate the Sport mode, press the SPORT button. 5 SPORT Button Once activated, a SPORT message will be displayed in the instrument cluster. 2. Press the SPORT button again to return to the standard driving mode. I nf or mat i onPr ovi dedby: 252 STARTING AND OPERATING BRAKE SYSTEM ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still function. However, there will be some loss of overall braking effectiveness. You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the “Brake System Warning Light.” Your vehicle is equipped with a advanced electronic brake control system that includes the Anti-Lock Brake System (ABS), Brake Assist System (BAS), Traction Control System (TCS), Hill Start Assist (HSA), and Electronic Stability Control (ESC). All systems work together to enhance vehicle stability and control in various driving conditions and are commonly referred to as ESC. In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating. The Four-Wheel ABS is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate computer to modulate hydraulic pressure, to prevent wheel lock-up and to help avoid skidding on slippery surfaces. Four-Wheel Anti-Lock Brake System (ABS) The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation, which is normal. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 253 The ABS includes an amber ABS Warning Light. When the light is illuminated, the ABS is not functioning. The system reverts to standard non-anti-lock brakes. Turning the ignition Off and On again may reset the ABS if the fault detected was only momentary. WARNING! • Pumping the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. WARNING! (Continued) • The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • The capabilities of an ABS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others. When you are in a severe braking condition involving the use of the ABS, you will experience some pedal drop as the vehicle comes to a stop. This is the result of the system reverting to the base brake system. Engagement of the ABS may be accompanied by a pulsing sensation. You may also hear a clicking noise. These occurrences are normal and indicate that the system is functioning properly. (Continued) I nf or mat i onPr ovi dedby: 5 254 STARTING AND OPERATING Brake Assist System (BAS) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the Anti-Lock Brake System (ABS). Applying the brakes very quickly results in the best BAS assistance. To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated. WARNING! • The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • The BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. • The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 255 Traction Control System (TCS) Hill Start Assist (HSA) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system, Brake Limited Differential (BLD), functions similar to a limited slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if TCS and ESC are in the Partial Off mode. Refer to “Electronic Stability Control (ESC)” in this section for further information. The HSA system is designed to assist the driver when starting a vehicle from a stop on a hill. HSA will maintain the level of brake pressure the driver applied for a short period of time after the driver takes his foot off the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill. The system will release brake pressure in proportion to the amount of throttle applied as the vehicle starts to move in the intended direction of travel. I nf or mat i onPr ovi dedby: 5 256 STARTING AND OPERATING HSA Activation Criteria The following criteria must be met in order for HSA to activate: • Vehicle must be stopped. WARNING! (Continued) could cause a collision with another vehicle or object. Always remember the driver is responsible for braking the vehicle. • Vehicle must be on a 2.5% (manual transmission) or 7% Disabling/Enabling HSA grade or greater (automatic transmission) hill. If you wish to turn the HSA system on or off, it can be • Gear selection matches vehicle uphill direction (i.e., done using the Customer Programmable Features in the vehicle in NEUTRAL (manual transmission), vehicle Electronic Vehicle Information Center (EVIC). Refer to facing uphill is in forward gear; vehicle backing uphill “Electronic Vehicle Information Center (EVIC)” in “Unis in REVERSE gear). derstanding Your Instrument Panel” for further information. WARNING! There may be situations on minor hills with a loaded vehicle, or while pulling a trailer, when the system will not activate and slight rolling may occur. This (Continued) I nf or mat i onPr ovi dedby: STARTING AND OPERATING 257 Electronic Stability Control (ESC) The Electronic Stability Control (ESC) system enhances directional control and stability of the vehicle under various driving conditions. ESC corrects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteering or understeering condition. Engine power may also be reduced to help the vehicle maintain the desired path. ESC uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting the oversteer or understeer condition. • Oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. I nf or mat i onPr ovi dedby: 5 ESC Off Switch (Automatic Transmission) 258 STARTING AND OPERATING WARNING! ESC Off Switch (Manual Transmission) NOTE: The ESC Off switch is located left of the steering column (Manual Transmission Only). The Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESC cannot prevent all accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. ESC also cannot prevent collisions resulting from loss of vehicle control due to inappropriate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of an ESC equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 259 NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or The ESC system has two available operating modes. gravel, it may be desirable to switch to the Partial Off Full On mode by pressing the switch. Once the situation requirThis is the normal operating mode for ESC. Whenever ing ESC to be switched to the Partial Off mode is the vehicle is started, the ESC system will be in On mode. overcome, turn ESC back on by momentarily pressing the This mode should be used for most driving situations. switch. This may be done while the vehicle is in motion. ESC should only be turned to Partial Off for specific WARNING! reasons as noted below. ESC Operating Modes Partial Off This mode is entered by momentarily pushing the ESC Off switch. This mode is intended to be used if the vehicle is in deep snow, sand or gravel conditions and more wheel spin than ESC would normally allow is required to gain traction. To turn ESC on again, momentarily pushing the switch again. This will restore the normal ESC On mode of operation. • When in “Partial Off” mode, the TCS functionality of ESC, (except for the limited slip feature described in the TCS section), has been disabled and the “ESC Off Indicator Light” will be illuminated. When in “Partial Off” mode, the engine power reduction feature of TCS is disabled, and the enhanced vehicle stability offered by the ESC system is reduced. I nf or mat i onPr ovi dedby: 5 260 STARTING AND OPERATING The ESC Activation/Malfunction Indicator Light also flashes when TCS is active. If the ESC Activation/ Malfunction Indicator Light begins to flash during acceleration, ease up on the accelerator and apply as little The ESC Activation/Malfunction Indicator Light in the instrument cluster will come on throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. when the ignition switch is turned to the MAR (ACC/ON/RUN) position for four seconds. If NOTE: the ESC Activation/Malfunction Indicator Light comes • The ESC Activation/Malfunction Indicator Light and on continuously with the engine running, a malfunction the ESC OFF Indicator Light come on momentarily has been detected in the ESC system. If this light remains each time the ignition switch is turned ON. on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than • Each time the ignition is turned ON, the ESC system 30 mph (48 km/h), see your authorized dealer as soon as will be ON even if it was turned off previously. possible to have the problem diagnosed and corrected. ESC Activation/Malfunction Indicator Light And ESC OFF Indicator Light The ESC Activation/Malfunction Indicator Light (located in the instrument cluster) starts to flash as soon as the tires lose traction and the ESC system becomes active. I nf or mat i onPr ovi dedby: The ESC OFF Indicator Light indicates the Electronic Stability Control (ESC) is partially off. STARTING AND OPERATING 261 TIRE SAFETY INFORMATION NOTE: Tire Markings • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter #P# is absent from this tire size designation. Example: 215/65R15 96H. 1 — U.S. DOT Safety Standards Code (TIN) 2 — Size Designation 3 — Service Description 4 — Maximum Load 5 — Maximum Pressure 6 — Treadwear, Traction and Temperature Grades • LT (Light Truck) — Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric tires is the same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preceding the size designation. Example: LT235/85R16. I nf or mat i onPr ovi dedby: 5 262 STARTING AND OPERATING • Temporary spare tires are designed for temporary • High flotation tire sizing is based on U.S. design emergency use only. Temporary high pressure comstandards and it begins with the tire diameter molded pact spare tires have the letter “T” or “S” molded into into the sidewall. Example: 31x10.5 R15 LT. the sidewall preceding the size designation. Example: T145/80D18 103M. Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or $....blank....$ = Passenger car tire based on European design standards, or LT = Light truck tire based on U.S. design standards, or T or S = Temporary spare tire or 31 = Overall diameter in inches (in) 215, 235, 145 = Section width in millimeters (mm) I nf or mat i onPr ovi dedby: STARTING AND OPERATING 263 EXAMPLE: 65, 85, 80 = Aspect ratio in percent (%) – Ratio of section height to section width of tire, or 10.5 = Section width in inches (in) R = Construction code – #R# means radial construction, or – #D# means diagonal or bias construction 15, 16, 18 = Rim diameter in inches (in) Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry I nf or mat i onPr ovi dedby: 5 264 STARTING AND OPERATING EXAMPLE: H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire: • XL = Extra load (or reinforced) tire, or • LL = Light load tire or • C, D, E, F, G = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load – Maximum load indicates the maximum load this tire is designed to carry Maximum Pressure – Maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire I nf or mat i onPr ovi dedby: STARTING AND OPERATING 265 Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side. Tires the outboard side, then you will find it on the inboard side of the tire. with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Tire Identification Number (TIN) EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits) 03 = Number representing the week in which the tire was manufactured (two digits) – 03 means the 3rd week I nf or mat i onPr ovi dedby: 5 266 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 01 = Number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represent the 3rd week of 1981 or 1991 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours. Inflation pressure is measured in units of PSI (pounds per square inch) or kPa (kilopascals). I nf or mat i onPr ovi dedby: STARTING AND OPERATING 267 Term Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Vehicle manufacturer’s recommended cold tire inflation pressure as shown on the tire placard. A label permanently attached to the vehicle describing the vehicle’s loading capacity, the original equipment tire sizes and the recommended cold tire inflation pressures. I nf or mat i onPr ovi dedby: 5 268 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Example Tire Placard Location (B-Pillar) Example Tire Placard Location (Door) I nf or mat i onPr ovi dedby: STARTING AND OPERATING 269 Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. Loading Tire And Loading Information Placard The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading” section of this manual. I nf or mat i onPr ovi dedby: 5 270 STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, Steps For Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occuaxles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or GAWRs, vehicle loading, and trailer towing, refer to XXX kg” on your vehicle’s placard. “Vehicle Loading” in this section. 2. Determine the combined weight of the driver and To determine the maximum loading conditions of your passengers that will be riding in your vehicle. vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or 3. Subtract the combined weight of the driver and passengers from XXX lbs or XXX kg. XXX kg” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 271 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle. The followbe five 150 lb (68 kg) passengers in your vehicle, the ing table shows examples on how to calculate total amount of available cargo and luggage load capacity load, cargo/luggage, and towing capacities of your is 650 lbs (295 kg) (since 5 x 150 lbs (68 kg) = 750 lbs vehicle with varying seating configurations and num(340 kg), and 1400 lbs (635 kg) – 750 lbs (340 kg) = ber and size of occupants. This table is for illustration 650 lbs [295 kg]). purposes only and may not be accurate for the seating 5. Determine the combined weight of luggage and cargo and load carry capacity of your vehicle. being loaded on the vehicle. That weight may not • For the following example, the combined weight of safely exceed the available cargo and luggage load occupants and cargo should never exceed 865 lbs capacity calculated in step 4. (392 kg). I nf or mat i onPr ovi dedby: 5 272 STARTING AND OPERATING I nf or mat i onPr ovi dedby: STARTING AND OPERATING 273 Safety WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Four primary areas are affected by improper tire pressure: • Safety and Vehicle Stability • Economy WARNING! • Improperly inflated tires are dangerous and can cause collisions. • Under-inflation increases tire flexing and can result in overheating and tire failure. • Over-inflation reduces a tire’s ability to cushion shock. Objects on the road and chuckholes can cause damage that result in tire failure. • Overinflated or under-inflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control. • Unequal tire pressures can cause steering problems. You could lose control of your vehicle. • Tread Wear (Continued) • Ride Comfort I nf or mat i onPr ovi dedby: 5 274 STARTING AND OPERATING Economy WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Underinflated tires will increase tire rolling resistance resulting in higher fuel consumption. Tread Wear Improper cold tire inflation pressures can cause abnormal wear patterns and reduced tread life, resulting in the Both under-inflation and over-inflation affect the stability need for earlier tire replacement. of the vehicle and can produce a feeling of sluggish Ride Comfort And Vehicle Stability response or over responsiveness in the steering. Proper tire inflation contributes to a comfortable ride. NOTE: Over-inflation produces a jarring and uncomfortable • Unequal tire pressures from side to side may cause ride. erratic and unpredictable steering response. • Unequal tire pressure from side to side may cause the vehicle to drift left or right. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 275 Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is The proper cold tire inflation pressure is listed on the defined as the tire pressure after the vehicle has not been driver’s side B-Pillar or rear edge of the driver’s side door. driven for at least three hours, or driven less than 1 mile At least once a month: (1.6 km) after sitting for a minimum of three hours. The cold tire inflation pressure must not exceed the maximum • Check and adjust tire pressure with a good quality inflation pressure molded into the tire sidewall. pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires Check tire pressures more often if subject to a wide range may look properly inflated even when they are under- of outdoor temperatures, as tire pressures vary with temperature changes. inflated. Tire Inflation Pressures • Inspect tires for signs of tire wear or visible damage. CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter. Example: If garage temperature = 68°F (20°C) and the outside temperature = 32°F (0°C) then the cold tire inflation pressure should be increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. I nf or mat i onPr ovi dedby: 5 276 STARTING AND OPERATING Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures For High Speed Operation WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious collision. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). The manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle Radial Ply Tires loading may be required for high-speed vehicle operation. Refer to your authorized tire dealer or original WARNING! equipment vehicle dealer for recommended safe operatCombining radial ply tires with other types of tires ing speeds, loading and cold tire inflation pressures. on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision. Always use radial ply tires in sets of four. Never combine them with other types of tires. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 277 Tire Repair Tire Types If your tire becomes damaged, it may be repaired if it All Season Tires — If Equipped meets the following criteria: All Season tires provide traction for all seasons (spring, summer, fall and winter). Traction levels may vary be• The tire has not been driven on when flat. tween different all season tires. All season tires can be • The damage is only on the tread section of your tire identified by the M+S, M&S, M/S or MS designation on (sidewall damage is not repairable). the tire sidewall. Use all season tires only in sets of four; • The puncture is no greater than a ¼ of an inch (6 mm). failure to do so may adversely affect the safety and handling of your vehicle. Consult an authorized tire dealer for tire repairs and additional information. Summer Or Three Season Tires — If Equipped Damaged Run Flat tires, or Run Flat tires that have experienced a loss of pressure should be replaced immediately with another Run Flat tire of identical size and service description (Load Index and Speed Symbol). Summer tires provide traction in both wet and dry conditions, and are not intended to be driven in snow or on ice. If your vehicle is equipped with summer tires, be aware these tires are not designed for winter or cold I nf or mat i onPr ovi dedby: 5 278 STARTING AND OPERATING driving conditions. Install winter tires on your vehicle when ambient temperatures are less than 40°F (5°C) or if roads are covered with ice or snow. For more information, contact an authorized dealer. Snow Tires Some areas of the country require the use of snow tires during the winter. Snow tires can be identified by a “mountain/snowflake” symbol on the tire sidewall. Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. WARNING! Do not use summer tires in snow/ice conditions. You could lose vehicle control, resulting in severe injury or death. Driving too fast for conditions also creates the possibility of loss of vehicle control. Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). For speeds above 75 mph (120 km/h) refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 279 While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states prohibit studded tires; therefore, local laws should be checked before using these tire types. It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the run flat mode. See the tire pressure monitoring section for more information. Run Flat Tires — If Equipped Spare Tires — If Equipped Run Flat tires allow you the capability to drive 50 miles NOTE: For vehicles equipped with Tire Service Kit (80 km) at 50 mph (80 km/h) after a rapid loss of inflation instead of a spare tire, please refer to “Tire Service Kit” in pressure. This rapid loss of inflation is referred to as the “What To Do In Emergencies” for further information. Run Flat mode. A Run Flat mode occurs when the tire inflation pressure is of/or below 14 psi (96 kPa). Once a CAUTION! Run Flat tire reaches the run flat mode it has limited driving capabilities and needs to be replaced immedi- Because of the reduced ground clearance, do not take ately. A Run Flat tire is not repairable. your vehicle through an automatic car wash with a compact or limited-use temporary spare installed. Damage to the vehicle may result. I nf or mat i onPr ovi dedby: 5 280 STARTING AND OPERATING Spare Tire Matching Original Equipped Tire And Wheel — If Equipped Your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact Spare Tire — If Equipped The compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on the Tire and Loading Information Placard located on the driver’s side door opening or on the sidewall of the tire. Compact spare tire descriptions begin with the letter “T” or “S” preceding the size designation. Example: T145/ 80D18 103M. T, S = Temporary Spare Tire Since this tire has limited tread life, the original equipment tire should be repaired (or replaced) and reinstalled on your vehicle at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tire. Do not install more than one compact spare tire and wheel on the vehicle at any given time. WARNING! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be I nf or mat i onPr ovi dedby: (Continued) STARTING AND OPERATING 281 Limited-Use Spare — If Equipped WARNING! (Continued) replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control. Full Size Spare — If Equipped The full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the temporary use full size spare tire needs to be replaced. Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. The limited-use spare tire is for temporary emergency use only. This tire is identified by a label located on the limited-use spare wheel. This label contains the driving limitations for this spare. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited-use spare tire affects vehicle handling. Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. I nf or mat i onPr ovi dedby: 5 282 STARTING AND OPERATING Tire Spinning WARNING! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your Tire and Loading Information Placard located on the driver’s side B-Pillar or the rear edge of the driver’s side door. Replace (or repair) the original equipment tire at the first opportunity and reinstall it on your vehicle. Failure to do so could result in loss of vehicle control. When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping. Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information. WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 283 These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes a 1/16 of an inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. replaced. Refer to “Replacement Tires” in this section for further information. Tread Wear Indicators Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style. • Tire pressure - Improper cold tire inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life, resulting in the need for earlier tire replacement. 1 — Worn Tire 2 — New Tire • Distance driven. I nf or mat i onPr ovi dedby: 5 284 STARTING AND OPERATING • Performance tires, tires with a speed rating of V or higher, and summer tires typically have a reduced tread life. Rotation of these tires per the vehicle maintenance schedule is highly recommended. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manufacturer strongly recommends that you use tires equivaWARNING! lent to the originals in size, quality and performance when replacement is needed. Refer to the paragraph on Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to “Tread Wear Indicator.” Refer to the Tire and Loading follow this warning can result in sudden tire failure. Information placard or the Vehicle Certification Label for You could lose control and have a collision resulting the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original in serious injury or death. equipment tire sidewall. See the Tire Sizing Chart exKeep dismounted tires in a cool, dry place with as little ample found in the Tire Safety Information section of this exposure to light as possible. Protect tires from contact manual for more information relating to the Load Index with oil, grease, and gasoline. and Speed Symbol of a tire. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 285 It is recommended to replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling. If you ever replace a wheel, make sure that the wheel’s specifications match those of the original wheels. It is recommended you contact your authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and WARNING! (Continued) braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death. Use only the tire and wheel sizes with load ratings approved for your vehicle. • Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. (Continued) I nf or mat i onPr ovi dedby: 5 286 STARTING AND OPERATING CAUTION! WARNING! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. TIRE CHAINS (TRACTION DEVICES) CAUTION! Use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage: • Traction device must be of proper size for the tire, as recommended by the traction device manufacturer. • Install on Front Tires. • Due to limited clearance, a 185/55R15 tire with a Security Chain Company (SCC) Super Z6 low profile traction device or equivalent is recommended. To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted traction device clearance between tires and other suspension components, it is important that only traction devices in good condition are used. Broken devices can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate device breakage. Remove the damaged parts of the device before further use. I nf or mat i onPr ovi dedby: (Continued) STARTING AND OPERATING 287 TIRE ROTATION RECOMMENDATIONS CAUTION! (Continued) • Install device as tightly as possible and then retighten after driving about ½ mile (0.8 km). • Do not exceed 30 mph (48 km/h). • Drive cautiously and avoid severe turns and large bumps, especially with a loaded vehicle. • Do not drive for a prolonged period on dry pavement. • Observe the traction device manufacturer’s instructions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufacturer’s if it is less than 30 mph (48 km/h). • Do not use traction devices on a compact spare tire. The tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels, and contribute to a smooth, quiet ride. Refer to the “Maintenance Schedule” for the proper maintenance intervals. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. I nf or mat i onPr ovi dedby: 5 288 STARTING AND OPERATING The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Tire Rotation TIRE PRESSURE MONITORING SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12° F (6.5° C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire sidewall. Refer to “Tires – General Information” in “Starting and Operating” for information on how to properly inflate the vehicle’s tires. The tire pressure will also increase as the vehicle is driven, this is normal and there should be no adjustment for this increased pressure. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 289 The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning limit for any reason, including low temperature effects, or natural pressure loss through the tire. The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold tire pressure on the placard. Once the low tire pressure warning (Tire Pressure Monitoring Telltale Light) illuminates, you must increase the tire pressure to the recommended cold tire pressure in order for the Tire Pressure Monitoring Telltale Light to turn off. The system will automatically update and the Tire Pressure Monitoring Telltale Light will turn off once the system receives the updated tire pressures. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) tire pressure of 30 psi (207 kPa). If the ambient temperature is 68° F (20° C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20° F (-7° C) will decrease the tire pressure to approximately 23 psi (159 kPa). This tire pressure is sufficiently low enough to turn on the Tire Pressure Monitoring Telltale Light. Driving the vehicle may cause the tire pressure to rise to approximately 27 psi (186 kPa), but the Tire Pressure Monitoring Telltale Light will still be on. In this situation, the Tire Pressure Monitoring Telltale Light will turn off only after the tires are inflated to the vehicle’s recommended cold tire pressure value. I nf or mat i onPr ovi dedby: 5 290 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket tire sealants may cause the Tire Pressure Monitoring System (TPMS) sensor to become inoperable. After using an aftermarket tire sealant it is recommended that you take your vehicle to your an authorized dealership to have your sensor function checked. • After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the Tire Pressure Monitoring Sensor. NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. (Continued) I nf or mat i onPr ovi dedby: STARTING AND OPERATING 291 • Driving on a significantly under-inflated tire causes Base System the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire This is the TPMS warning indicator located in the tread life, and may affect the vehicle’s handling and instrument cluster. stopping ability. The TPMS uses wireless technology with wheel rim • The TPMS is not a substitute for proper tire mainte- mounted electronic sensors to monitor tire pressure levnance, and it is the driver’s responsibility to maintain els. Sensors, mounted to each wheel as part of the valve correct tire pressure using an accurate tire gauge, even stem, transmit tire pressure readings to the Receiver if under-inflation has not reached the level to trigger Module. illumination of the Tire Pressure Monitoring Telltale NOTE: It is particularly important for you to check the Light. tire pressure in all of the tires on your vehicle regularly • Seasonal temperature changes will affect tire pressure, and to maintain the proper pressure. and the TPMS will monitor the actual tire pressure in The TPMS consists of the following components: the tire. • Receiver Module. • Four Tire Pressure Monitoring Sensors. • Tire Pressure Monitoring Telltale Light. I nf or mat i onPr ovi dedby: 5 292 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings the “Service Tire Pressure Monitoring System” text message will display. If the ignition key is cycled, this sequence will repeat providing the system fault still exists. The Tire Pressure Monitoring Telltale Light will turn off when the fault condition no longer exists. A system fault can occur with any of the following scenarios: The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster, an audible chime will be activated, and the “Check left or right front/rear tire xxx.x psi” text message will display when one or more of the four active road tire pressures are low. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate 1. Jamming due to electronic devices or driving next to each tire to the vehicle’s recommended cold placard facilities emitting the same radio frequencies as the pressure value. The system will automatically update TPM sensors. and the Tire Pressure Monitoring Light will extinguish 2. Installing some form of aftermarket window tinting once the updated tire pressures have been received. The that affects radio wave signals. vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. 3. Snow or ice around the wheels or wheel housings. Check TPMS Warnings 4. Using tire chains on the vehicle. The Tire Pressure Monitoring Telltale Light will flash on 5. Using wheels/tires not equipped with TPM sensors. and off for 75 seconds and remain on solid when a system fault is detected, an audible chime will be activated and I nf or mat i onPr ovi dedby: STARTING AND OPERATING 293 NOTE: Your vehicle may be equipped with a compact 4. This occurs for each subsequent ignition key cycle, a spare wheel and tire assembly. chime will sound and the Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and 1. The compact spare tire does not have a tire pressure then remain on solid. monitoring sensor. Therefore, the TPMS will not monitor the tire pressure in the compact spare tire. 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare 2. If you install the compact spare tire in place of a road tire, the TPMS will update automatically and the Tire tire that has a pressure below the low-pressure warnPressure Monitoring Telltale Light will turn OFF, as ing limit, upon the next ignition key cycle, a chime will long as no tire pressure is below the low-pressure sound and the Tire Pressure Monitoring Telltale Light warning limit in any of the four active road tires. The will still turn ON due to the low tire. vehicle may need to be driven for up to 20 minutes 3. However, after driving the vehicle for up to 20 minabove 15 mph (24 km/h) in order for the TPMS to receive this information. utes above 15 mph (24 km/h), the Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and then remain on solid. I nf or mat i onPr ovi dedby: 5 294 STARTING AND OPERATING • Various Tire Pressure Monitoring System messages, which display in the Electronic Vehicle Information When the vehicle is equipped with an enhanced TPM Center (EVIC) system, the driver can view text messages showing the actual tire pressure value by position by selecting the tire • Tire Pressure Monitoring Telltale Light pressure menu command in the instrument cluster. Refer Tire Pressure Monitoring Low Pressure Warnings to the instrument panel features section of the owners The “Tire Pressure Monitoring Telltale Light” will manual. illuminate in the instrument cluster and a chime will Premium TPM System sound when tire pressure is low in one or more of the The Tire Pressure Monitor System (TPMS) uses wireless four active road tires. In addition, the Electronic technology with wheel rim mounted electronic sensors to Vehicle Information Center (EVIC) will display a monitor tire pressure levels. Sensors, mounted to each graphic showing the pressure values of each tire with wheel as part of the valve stem, transmit tire pressure the low tire pressure tire highlighted in a different readings to the receiver module. color. Enhanced System — If Equipped The TPMS consists of the following components: • Receiver module • Four Tire Pressure Monitoring Sensors I nf or mat i onPr ovi dedby: STARTING AND OPERATING 295 receives the updated tire pressures, the system will automatically update and the “Tire Pressure Monitoring Telltale Light” will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. TPMS Warning When a system fault is detected, the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and then remain on solid. The system fault will sound a chime and also display a “Service Tire Pressure Monitoring System” message in the EVIC for approxiLow Tire Indicator mately 5 seconds and then display dashes (- -) in place of Should this occur, you should stop as soon as possible and the pressure value to indicate which sensor is not being inflate the tires with low pressure to the vehicle’s recom- received. mended cold placard pressure value. Once the system I nf or mat i onPr ovi dedby: 5 296 STARTING AND OPERATING A system fault can occur due to any of the following: 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accumulation of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. Service TPM System Message 5. Using wheels/tires not equipped with TPM sensors. If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “Tire Pressure Monitoring Telltale Light” will no longer flash, and the “Service Tire Pressure Monitoring System” message will no longer display, and a pressure value will display in place of the dashes. The EVIC will also display a #Service Tire Pressure Monitoring System# message for a minimum of five seconds when a system fault related to an incorrect sensor location fault is detected. In this case, the #Service Tire Pressure Monitoring System# message is then followed with a graphic display with pressure values still I nf or mat i onPr ovi dedby: STARTING AND OPERATING 297 shown. This indicates that the pressure values are still • After driving the vehicle for up to 20 minutes above being received from the TPM sensors but they may not be 15 mph (24 km/h), the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and located in the correct vehicle position. The system still then remain on solid. In addition, the EVIC will needs to be serviced as long as the #Service Tire Pressure display a “Service TPM System” message and then Monitoring System# message is displayed. display dashes (- -) in place of the pressure value. NOTE: • For each subsequent ignition switch cycle, a chime will • The TPMS will not monitor the pressure in a replacesound, the “Tire Pressure Monitoring Telltale Light” ment tire installed without a tire pressure sensor. will flash on and off for 75 seconds and then remain on solid, and the EVIC will display a “Service Tire Pres• If you install a replacement tire in place of a road tire sure Monitoring System” message and dashes (- -) in that has a pressure below the low-pressure warning place of the pressure value. limit, upon the next ignition switch cycle, the “Tire Pressure Monitoring Telltale Light” will remain on and Once you repair or replace the original road tire and a chime will sound. In addition, the graphic in the reinstall it, the TPMS will update automatically. In addiEVIC will still display a pressure value highlighted in tion, the “Tire Pressure Monitoring Telltale Light” will a different color. turn off and the graphic in the EVIC will display a new I nf or mat i onPr ovi dedby: 5 298 STARTING AND OPERATING pressure value instead of dashes (- -), as long as no tire The tire pressure sensors are covered under one of the pressure is below the low-pressure warning limit in any following licenses: of the four active road tires. The vehicle may need to be MRXC4W4MA4 driven for up to 20 minutes above 15 mph (24 km/h) in United States order for the TPMS to receive this information. Canada 2546A-C4W4MA4 (Single) General Information This device complies with Part 15 of the FCC rules and FUEL REQUIREMENTS — 1.4L Engine RSS 210 of Industry Canada. Operation is subject to the following conditions: This engine is designed to meet all emis• This device may not cause harmful interference. sion regulations and provide satisfactory fuel economy and performance when us• This device must accept any interference received, ing high-quality unleaded #regular# gasoincluding interference that may cause undesired opline with a minimum octane rating of 87. eration. For optimum performance and fuel economy the use of 91 octane or higher is recommended. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 299 Light spark knock at low engine speeds is not harmful to Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, try another brand of gasoline (with the appropriate octane rating for your engine) before considering service for the vehicle. Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, try another brand of gasoline (with the appropriate octane rating for your engine) before considering service for the vehicle. FUEL REQUIREMENTS — 1.4L Turbo Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasoline contain oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. This engine is designed to meet all emission regulations and provide satisfactory fuel economy and performance when using high-quality unleaded “regular” gasoline with a minimum octane rating of 87. The manufacturer supports the use of reformulated gasoFor optimum performance and fuel economy the use of line. Properly blended reformulated gasoline will pro91 octane or higher is recommended. vide excellent performance and durability of engine and fuel system components. I nf or mat i onPr ovi dedby: 5 300 STARTING AND OPERATING Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% Ethanol, Methyl Tert-Butyl Ether (MTBE), and Ethyl Tret-Butyl Ether (ETBE). Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing 10% ethanol (E10). Gasoline with higher ethanol content may void the New Vehicle Limited Warranty. CAUTION! Do not use gasoline containing Methanol or E-85 Ethanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system components. Problems that result from using methanol/gasoline blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol. If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: • Operate in a lean mode. • OBD II “Malfunction Indicator Light” on. • Poor engine performance. • Poor cold start and cold drivability. • Increased risk for fuel system component corrosion. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 301 To fix a Non-FFV vehicle inadvertently fueled once with MMT. Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some E-85 perform the following: vehicles. The manufacturer recommends that gasoline • Drain the fuel tank (see your authorized dealer). without MMT be used in your vehicle. The MMT content of gasoline may not be indicated on the gasoline pump, • Change the engine oil and oil filter. therefore, you should ask your gasoline retailer whether • Disconnect and reconnect the battery to reset the the gasoline contains MMT. MMT is prohibited in Federal engine controller memory. and California reformulated gasoline. More extensive repairs will be required for prolonged Materials Added To Fuel exposure to E-85 fuel. All gasoline sold in the United States is required to MMT In Gasoline contain effective detergent additives. Use of additional Methylcyclopentadienyl Manganese Tricarbonyl (MMT) detergents or other additives is not needed under normal is a manganese-containing metallic additive that is conditions and they would result in additional cost. blended into some gasoline to increase octane. Gasoline Therefore, you should not have to add anything to the blended with MMT provides no performance advantage fuel. beyond gasoline of the same octane number without I nf or mat i onPr ovi dedby: 5 302 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emissions control system. • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized dealer for service assistance. • The use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against you. (Continued) I nf or mat i onPr ovi dedby: STARTING AND OPERATING 303 Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period. If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located on the passenger side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle. (Continued) I nf or mat i onPr ovi dedby: 5 304 STARTING AND OPERATING CAUTION! (Continued) into the fuel system. Also, a poorly fitting aftermarket cap can cause the “Malfunction Indicator Light (MIL)” to illuminate, due to fuel vapors escaping from the system. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. WARNING! Fuel Filler Cap CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel filler cap. A poorly fitting cap could let impurities • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel when the engine is running. It may cause the MIL to turn on and could cause a fire. (Continued) I nf or mat i onPr ovi dedby: (Continued) STARTING AND OPERATING 305 Loose Fuel Filler Cap Message WARNING! (Continued) After fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged. If the system detects a malfunction, the “gASCAP” message will display in the odometer display. Tighten the gas cap until a #clicking# sound is heard. This is an indication that the gas cap is NOTE: properly tightened. Press the odometer reset button to • When the fuel nozzle “clicks” or shuts off, the fuel tank turn the message off. If the problem persists, the message is full. will appear the next time the vehicle is started. This • Tighten the gas cap about 1/4 turn until you hear one might indicate a damaged cap. If the problem is detected click. This is an indication that the cap is properly twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL off. tightened. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. • If the gas cap is not tightened properly, the MIL will TRAILER TOWING come on. Be sure the gas cap is tightened every time Trailer towing with this vehicle is not recommended. the vehicle is refueled. I nf or mat i onPr ovi dedby: 5 306 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Flat Tow Wheels OFF the Ground NONE Dolly Tow Front Rear ALL On Trailer Manual Transmission Transmission in NEUTRAL OK NOT ALLOWED OK Automatic Transmission NOT ALLOWED OK NOT ALLOWED OK This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are OFF the ground. CAUTION! This vehicle may also be towed using a tow dolly (with the front wheels OFF the ground). DO NOT flat tow any vehicle equipped with an automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are OFF the ground. Vehicles equipped with manual transmissions may be flat towed (with all four wheels on the ground) at any legal highway speed, for any distance, if the manual transmission is in NEUTRAL. I nf or mat i onPr ovi dedby: STARTING AND OPERATING 307 CAUTION! Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. 5 I nf or mat i onPr ovi dedby: I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES CONTENTS ! HAZARD WARNING FLASHERS . . . . . . . . . . .311 ! JACKING AND TIRE CHANGING — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . ! IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .311 ▫ Jack Location . . . . . . . . . . . . . . . . . . ! TIRE SERVICE KIT — IF EQUIPPED . . . . . . . . .312 ▫ Spare Tire Removal . . . . . . . . . . . . . . ▫ Tire Service Kit Storage . . . . . . . . . . . . . . . . .313 ▫ Preparations For Jacking . . . . . . . . . . ▫ Tire Service Kit Components And Operation . .313 ▫ Jacking Instructions . . . . . . . . . . . . . ▫ Tire Service Kit Usage Precautions. . . . . . . . . .314 ▫ Road Tire Installation . . . . . . . . . . . . . ▫ Sealing A Tire With Tire Service Kit . . . . . . . . .317 ▫ Spare Tire Stowage . . . . . . . . . . . . . . ! WHEEL AND TIRE TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . .323 ! JUMP-STARTING PROCEDURE . . . . . . ▫ Torque Specifications . . . . . . . . . . . . . . . . . . .323 . . . . . .324 . . . . . .325 . . . . . .326 . . . . . .328 . . . . . .329 . . . . . .335 . . . . . .337 . . . . . .337 ▫ Preparations For Jump-Start . . . . . . . . . . . . . .338 I nf or mat i onPr ovi dedby: 6 310 WHAT TO DO IN EMERGENCIES ▫ Jump-Starting Procedure . . . . . . . . . . . . . . . .340 ! TOWING A DISABLED VEHICLE . . . . . . . . . . .345 ! FREEING A STUCK VEHICLE . . . . . . . . . . . . .342 ▫ Automatic Transmission . . . . . . . . . . . . . . . . .346 ! SHIFT LEVER OVERRIDE . . . . . . . . . . . . . . . .343 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . .347 ! ENHANCED ACCIDENT RESPONSE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . .347 I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 311 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel below the radio. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning • On the highways — slow down. flashers. When the switch is activated, all direc- • In city traffic — while stopped, place the transmission tional turn signals will flash on and off to warn oncoming in NEUTRAL, but do not increase engine idle speed. traffic of an emergency. Press the switch a second time to NOTE: There are steps that you can take to slow down turn off the Hazard Warning flashers. an impending overheat condition: Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled • If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and and it is creating a safety hazard for other motorists. turning the A/C off can help remove this heat. If it is necessary to leave the vehicle to go for service, the Hazard Warning flashers will continue to operate with • You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to the ignition key removed and the vehicle locked. high. This allows the heater core to act as a supplement NOTE: With extended use, the Hazard Warning flashers to the radiator and aids in removing heat from the may wear down your battery. engine cooling system. I nf or mat i onPr ovi dedby: 6 312 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! (Continued) Driving with a hot cooling system could damage your vehicle. If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the normal range. If the pointer remains on the H (red) mark for more than a minute, turn the engine off immediately and call for service. you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If TIRE SERVICE KIT — IF EQUIPPED Small punctures up to ¼” (6 mm) in the tire tread can be sealed with Tire Service Kit. Foreign objects (e.g., screws or nails) should not be removed from the tire. Tire Service Kit can be used in outside temperatures down to approximately -4°F (-20°C). This kit will provide a temporary tire seal, allowing you to drive your vehicle up to 100 miles (160 km) with a maximum speed of 55 mph (90 km/h). (Continued) I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 313 Tire Service Kit Storage Tire Service Kit Components And Operation The Tire Service Kit is located under the front driver’s seat. 6 Tire Service Kit Components 1 — Sealant Bottle Tire Service Kit Location 5 — Mode Select Knob 2 — Deflation Button 6 — Sealant Hose (Clear) 3 — Pressure Gauge 7 — Air Pump Hose (Black) 4 — Power Button 8 — Power Plug (located on the bottom side of the Tire Service Kit) I nf or mat i onPr ovi dedby: 314 WHAT TO DO IN EMERGENCIES Using The Power Button Using The Mode Select Knob And Hoses Your Tire Service Kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push and release the Power Button (4) once to turn On the Tire Service Kit. Push and release the Power Button (4) again to turn Off the Tire Service Kit. Push in the Mode Select Knob (5) and turn to this position for air pump operation only. Use Using The Deflation Button the Black Air Pump Hose (7) when selecting Press the Deflation Button (2) to reduce the air this mode. pressure in the tire if it becomes over-inflated. Selecting Sealant Mode Push in the Mode Select Knob (5) and Tire Service Kit Usage Precautions turn to this position to inject the Tire • Replace the Tire Service Kit Sealant Bottle (1) and Service Kit Sealant and to inflate the Sealant Hose (6) prior to the expiration date (printed at tire. Use the Sealant Hose (clear hose) the lower right hand corner on the bottle label) to (6) when selecting this mode. assure optimum operation of the system. Refer to “Sealing a Tire with Tire Service Kit” section (F) “Sealant Bottle and Hose Replacement”. I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 315 • When the Tire Service Kit sealant is in a liquid form, clean water, and a damp cloth will remove the material from the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the Tire Service Kit. • You can use the Tire Service Kit air pump to inflate bicycle tires. The kit also comes with two needles, located in the Accessory Storage Compartment (on the bottom of the air pump) for inflating sport balls, rafts, or similar inflatable items. However, use only the Air Pump Hose (7) and Tire Service Kit Expiration Date Location make sure the Mode Select Knob (5) is in the Air Mode • The Sealant Bottle (1) and Sealant Hose (6) are a one when inflating such items to avoid injecting sealant into tire application use and need to be replaced after each them. The Tire Service Kit Sealant is only intended to seal use. Always replace these components immediately at punctures less than ¼” (6 mm) diameter in the tread of your original equipment vehicle dealer. your vehicle. • Do not lift or carry the Tire Service Kit by the hoses. I nf or mat i onPr ovi dedby: 6 316 WHAT TO DO IN EMERGENCIES WARNING! WARNING! (Continued) • Do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the Tire Service Kit. • Do not use Tire Service Kit or drive the vehicle under the following circumstances: – If the puncture in the tire tread is approximately 1/4” (6 mm) or larger. – If the tire has any sidewall damage. – If the tire has any damage from driving with extremely low tire pressure. – If the tire has any damage from driving on a flat tire. – If the wheel has any damage. – If you are unsure of the condition of the tire or the wheel. • Keep Tire Service Kit away from open flames or heat source. • A loose Tire Service Kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the Tire Service Kit in the place provided. Failure to follow these warnings can result in injuries that are serious or fatal to you, your passengers, and others around you. • Take care not to allow the contents of Tire Service Kit to come in contact with hair, eyes, or clothing. Tire Service Kit is harmful if inhaled, swallowed, or absorbed through the skin. It causes skin, eye, and respiratory irritation. Flush immediately with plenty of water if there is any contact with eyes or skin. Change clothing as soon as possible, if there is any contact with clothing. (Continued) I nf or mat i onPr ovi dedby: (Continued) WHAT TO DO IN EMERGENCIES 317 WARNING! (Continued) • Tire Service Kit Sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immediately. Keep Tire Service Kit out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomiting! Consult a physician immediately. on the ground. This will provide the best positioning of the kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceeding. 3. Place the transmission in PARK (auto transmission) or in Gear (manual transmission) and turn Off the ignition. 4. Set the parking brake. Sealing A Tire With Tire Service Kit (A) Whenever You Stop To Use Tire Service Kit: (B) Setting Up To Use Tire Service Kit: 1. Push in the Mode Select Knob (5) and turn to the 1. Pull over to a safe location and turn on the vehicle’s Sealant Mode position. Hazard Warning flashers. 2. Uncoil the Sealant Hose (6) and then remove the cap 2. Verify that the valve stem (on the wheel with the from the fitting at the end of the hose. deflated tire) is in a position that is near to the ground. This will allow the Tire Service Kit Hoses (6) and (7) to 3. Place the Tire Service Kit flat on the ground next to the deflated tire. reach the valve stem and keep the Tire Service Kit flat I nf or mat i onPr ovi dedby: 6 318 WHAT TO DO IN EMERGENCIES 4. Remove the cap from the valve stem and then screw NOTE: Sealant may leak out through the puncture in the the fitting at the end of the Sealant Hose (6) onto the tire. valve stem. If the sealant (white fluid) does not flow within 0 – 10 5. Uncoil the Power Plug (8) and insert the plug into the seconds through the Sealant Hose (6): vehicle’s 12 Volt power outlet. 1. Press the Power Button (4) to turn Off the Tire Service NOTE: Do not remove foreign objects (e.g., screws or nails) from the tire. (C) Injecting Tire Service Kit Sealant Into The Deflated Tire: • Always start the engine before turning ON the Tire Service Kit. Kit. Disconnect the Sealant Hose (6) from the valve stem. Make sure the valve stem is free of debris. Reconnect the Sealant Hose (6) to the valve stem. Check that the Mode Select Knob (5) is in the Sealant Mode position and not Air Mode. Press the Power Button (4) to turn On the Tire Service Kit. 2. Connect the Power Plug (8) to a different 12 Volt power outlet in your vehicle or another vehicle, if NOTE: Manual transmission vehicles must have the available. Make sure the engine is running before parking brake engaged and the shift lever in NEUTRAL. turning ON the Tire Service Kit. • After pressing the Power Button (4), the sealant (white fluid) will flow from the Sealant Bottle (1) through the 3. The Sealant Bottle (1) may be empty due to previous use. Call for assistance. Sealant Hose (6) and into the tire. I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 319 NOTE: If the Mode Select Knob (5) is on Air Mode and If the tire does not inflate to at least 26 psi (1.8 Bar) the pump is operating, air will dispense from the Air pressure within 15 minutes: Pump Hose (7) only, not the Sealant Hose (6). • The tire is too badly damaged. Do not attempt to drive If the sealant (white fluid) does flow through the the vehicle further. Call for assistance. Sealant Hose (6): NOTE: If the tire becomes over-inflated, press the Defla1. Continue to operate the pump until sealant is no longer tion Button to reduce the tire pressure to the recomflowing through hose (typically takes 30 - 70 seconds). mended inflation pressure before continuing. As the sealant flows through the Sealant Hose (6), the If the tire inflates to the recommended pressure or is at Pressure Gauge (3) can read as high as 70 psi (4.8 Bar). The Pressure Gauge (3) will decrease quickly from least 26 psi (1.8 Bar) pressure within 15 minutes: approximately 70 psi (4.8 Bar) to the actual tire pressure 1. Press the Power Button (4) to turn off the Tire Service when the Sealant Bottle (1) is empty. Kit. 2. The pump will start to inject air into the tire immedi- 2. Remove the Speed Limit sticker from the top of the ately after the Sealant Bottle (1) is empty. Continue to Sealant Bottle (1) and place the sticker on the instruoperate the pump and inflate the tire to the pressure ment panel. indicated on the tire pressure label on the driver-side latch pillar (recommended pressure). Check the tire pressure by looking at the Pressure Gauge (3). I nf or mat i onPr ovi dedby: 6 320 WHAT TO DO IN EMERGENCIES 3. Immediately disconnect the Sealant Hose (6) from the valve stem, reinstall the cap on the fitting at the end of the hose, and place the Tire Service Kit in the vehicle storage location. Quickly proceed to (D) “Drive Vehicle.” (D) Drive Vehicle: Immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure distribution of the Tire Service Kit Sealant within the tire. Do not exceed 55 mph (90 km/h). CAUTION! WARNING! • The metal end fitting from Power Plug (8) may get hot after use, so it should be handled carefully. • Failure to reinstall the cap on the fitting at the end of the Sealant Hose (6) can result in sealant contacting your skin, clothing, and the vehicle’s interior. It can also result in sealant contacting internal Tire Service Kit components which may cause permanent damage to the kit. Tire Service Kit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using Tire Service Kit. Do not exceed 55 mph (90 km/h) until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, and others around you. I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 321 (E) After Driving: If the tire pressure is 19 psi (1.3 Bar) or higher: Pull over to a safe location. Refer to “Whenever You Stop 1. Press the Power Button (4) to turn on Tire Service Kit to Use Tire Service Kit” before continuing. and inflate the tire to the pressure indicated on the tire and loading information label on the driver-side door 1. Push in the Mode Select Knob (5) and turn to the Air opening. Mode position. 2. Uncoil the power plug and insert the plug into the NOTE: If the tire becomes over-inflated, press the Deflation Button to reduce the tire pressure to the recomvehicle’s 12 Volt power outlet. mended inflation pressure before continuing. 3. Uncoil the Air Pump Hose (7) (black in color) and screw the fitting at the end of hose (7) onto the valve 2. Disconnect the Tire Service Kit from the valve stem, reinstall the cap on the valve stem and unplug from stem. 12 Volt outlet. 4. Check the pressure in the tire by reading the Pressure 3. Place the Tire Service Kit in its proper storage area in Gauge (3). the vehicle. If tire pressure is less than 19 psi (1.3 Bar): 4. Have the tire inspected and repaired or replaced at the The tire is too badly damaged. Do not attempt to drive earliest opportunity at an authorized dealer or tire the vehicle further. Call for assistance. service center. I nf or mat i onPr ovi dedby: 6 322 WHAT TO DO IN EMERGENCIES 5. Remove the Speed Limit sticker from the instrument 4. Clean any remaining sealant from the Tire Service Kit housing. panel after the tire has been repaired. 6. Replace the Sealant Bottle (1) and Sealant Hose (6) 5. Position the new Sealant Bottle (1) in the housing so that the Sealant Hose (6) aligns with the hose slot in assembly at your authorized dealer as soon as posthe front of the housing. Press the bottle into the sible. Refer to (F) “Sealant Bottle and Hose Replacehousing. An audible click will be heard indicating the ment”. bottle is locked into place. NOTE: When having the tire serviced, advise the authorized dealer or service center that the tire has been sealed 6. Verify that the cap is installed on the fitting at the end of the Sealant Hose (6) and return the hose to its using the Tire Service Kit. storage area (located on the bottom of the air pump). (F) Sealant Bottle And Hose Replacement: 7. Return the Tire Service Kit to its storage location in the 1. Uncoil the Sealant Hose (6) (clear in color). vehicle. 2. Locate the round Sealant Bottle release button in the recessed area under the sealant bottle. 3. Press the Sealant Bottle release button. The Sealant Bottle (1) will pop up. Remove the bottle and dispose of it accordingly. I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 323 WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench. Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Torque Specifications Lug Nut/Bolt Torque **Lug Nut/ Bolt Size 66 Ft-Lbs (90 N·m) Steel Wheels Only 75 Ft-Lbs (100 N·m) Aluminum Wheels Only M12 x 1.25 Lug Nut/ Bolt Socket Size 17 mm 6 Wheel Mounting Surface **Use only Chrysler recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. I nf or mat i onPr ovi dedby: 324 WHAT TO DO IN EMERGENCIES Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. JACKING AND TIRE CHANGING — IF EQUIPPED WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Torque Patterns After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. I nf or mat i onPr ovi dedby: (Continued) WHAT TO DO IN EMERGENCIES 325 Jack Location WARNING! (Continued) • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Never start or run the engine while the vehicle is on a jack. • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. The jack and jack wrench tool are stowed in a bag under the front driver’s seat. 6 Jack And Jack-Handle Location I nf or mat i onPr ovi dedby: 326 WHAT TO DO IN EMERGENCIES 2. Fit the wrench tool over the drive nut. Use the wrench to rotate the nut counterclockwise until the spare is on The spare tire is stowed to the underbody below the the ground with enough slack in the cable to allow you cargo area. to pull the tire out from under the vehicle. 1. Remove the plug located in the rear cargo area. Spare Tire Removal Lowering/Raising Spare Tire Winch Access Plug I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 327 CAUTION! The winch mechanism is designed for use with the jack wrench tool only. Use of an air wrench or other power tools is not recommended and they can damage the winch. 3. Pull the spare tire out from under the vehicle. Spare Tire I nf or mat i onPr ovi dedby: 6 328 WHAT TO DO IN EMERGENCIES 4. Tilt the retainer at the end of the cable and pull it Preparations For Jacking through the center of the wheel. 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Turn on the Hazard Warning flashers. 3. Set the parking brake. Retainer 4. Place the shift lever in PARK (automatic transmission) or REVERSE (manual transmission). I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 329 5. Turn Off the ignition. Jacking Instructions 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: Passengers should not remain in the vehicle while the vehicle is being jacked. WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flashers. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE. • Never start or run the engine with the vehicle on a jack. (Continued) I nf or mat i onPr ovi dedby: 6 330 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. Jack Warning Label NOTE: Refer to the “Compact Spare Tire” section of the “Tires-General Information” under “Starting And Operating” for information about the spare tire, it’s use, and operation. CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Remove the scissors jack and tool bag from under the driver’s seat. I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 331 2. Remove center cap. 3. Loosen, but do not remove, the wheel bolts by turning them to the left one turn while the wheel is still on the ground. NOTE: There are front and rear jacking locations on each side of the body (as indicated by the triangular lift point symbol on the sill molding). 6 Center Cap Removal NOTE: Before using the swivel wrench to remove the wheel bolts be sure to remove the center cap of the wheel by inserting the angled tab end of the swivel wrench into the notched part of the center cap. Front Jacking Location I nf or mat i onPr ovi dedby: 332 WHAT TO DO IN EMERGENCIES 4. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. Rear Jacking Location Do not raise the vehicle until you are sure the jack is securely engaged. Jack Location I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 333 WARNING! WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. To avoid the risk of forcing the vehicle off the jack, do not fully tighten the wheel bolts until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 5. Using the swivel wrench, raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. 6. Remove the wheel bolts and pull the wheel off the hub. For vehicles equipped with aluminum wheels, the center caps must be removed to remove the wheel bolts. For vehicles equipped with steel wheels the wheel covers must be removed to remove the wheel bolts. CAUTION! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. I nf or mat i onPr ovi dedby: 6 334 WHAT TO DO IN EMERGENCIES 7. Install the spare wheel and wheel bolts with the cone shaped end of the bolts toward the wheel. Lightly tighten the bolts. To avoid the risk of forcing the vehicle off the jack, do not tighten the bolts fully until the vehicle has been lowered. 8. Lower the vehicle by turning the jack screw to the left. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 9. Finish tightening the wheel bolts. Push down on the 11. Place the deflated (flat) tire in the cargo area. Have the tire repaired or replaced as soon as possible. wrench while at the end of the handle for increased leverage. Tighten the wheel bolts in a star pattern until WARNING! each bolt has been tightened twice. For the correct wheel bolt torque refer to Torque Specifications in this A loose tire thrown forward in a collision or hard stop section. If in doubt about the correct tightness, have could injure the occupants in the vehicle. Have the them checked with a torque wrench by your authodeflated (flat) tire repaired or replaced immediately. rized dealership or service station. 10. Disassemble the jack and tools and place them in the 12. Check the spare tire pressure as soon as possible. Correct the tire pressure as required. bag. Stow it under the driver’s seat and secure the bag to the floor with the straps attached to the floor of the vehicle. I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 335 Road Tire Installation Vehicles Equipped With Wheel Covers 1. Mount the road tire on the axle. 2. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand. Do not use a hammer or excessive force to install the cover. Tire And Wheel Cover Or Center Cap 1 — Valve Stem 2 — Valve Notch 3 — Wheel Bolt I nf or mat i onPr ovi dedby: 4 — Wheel Cover 5 — Road Wheel 6 336 WHAT TO DO IN EMERGENCIES 3. Install the four wheel bolts with the cone shaped end of Vehicles Without Wheel Covers the nut toward the wheel. Lightly tighten the wheel bolts. 1. Mount the road tire on the axle. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel bolts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 4. Lower the vehicle to the ground by turning the jack handle counterclockwise. 2. Install the remaining wheel bolts with the cone shaped end of the nut toward the wheel. Lightly tighten the wheel bolts. WARNING! To avoid the risk of forcing the vehicle off the jack, do not fully tighten the lug nuts until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 5. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased 3. Lower the vehicle to the ground by turning the jack leverage. Refer to “Torque Specifications” in this sechandle counterclockwise. tion for correct wheel bolt torque. 6. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel bolts are properly seated against the wheel. I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 337 4. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased leverage. Refer to “Torque Specifications” in this section for correct wheel bolt torque. CAUTION! The winch mechanism is designed for use with the jack wrench extension tool only. Use of air wrench or power tool may damage the winch. 5. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel bolts are JUMP-STARTING PROCEDURE properly seated against the wheel. If your vehicle has a discharged battery, it can be jumpSpare Tire Stowage started using a set of jumper cables and a battery in Reverse instructions of the spare removal section. another vehicle or by using a portable battery booster Rotate the jack wrench tool on the winch drive nut pack. Jump-starting can be dangerous if done improperly clockwise until effort becomes heavy and an audible click so please follow the procedures in this section carefully. is heard indicating the spare is properly stowed. NOTE: When using a portable battery booster pack, follow the manufacturer’s operating instructions and precautions. I nf or mat i onPr ovi dedby: 6 338 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur. Battery Posts Preparations For Jump-Start The battery in your vehicle is located between the left 1 — Positive (+) Post (Covered With Protective Cap) front headlight assembly and the left front wheel splash 2 — Negative (-) Post shield. I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 339 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive. Keep open flames or sparks away from the battery. 3. Remove the protective cover over the positive (+) battery post. To remove the cover, press the locking tab and pull upward on the cover. 4. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. WARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. 1. Set the parking brake, shift the automatic transmission into PARK and turn the ignition to LOCK. 2. Turn off the heater, radio, and all unnecessary electrical accessories. I nf or mat i onPr ovi dedby: 6 340 WHAT TO DO IN EMERGENCIES 3. Connect the negative end (-) of the jumper cable to the negative (-) post of the booster battery. Jump-Starting Procedure WARNING! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion. 4. Connect the opposite end of the negative (-) jumper cable to a good engine ground (exposed metal part of the discharged vehicle’s engine) away from the battery and the fuel injection system. WARNING! CAUTION! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Connecting The Jumper Cables 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. Only use the specific ground point, do not use any other exposed metal parts. 2. Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery. I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 341 5. Start the engine in the vehicle that has the booster 4. Disconnect the positive (+) end of the jumper cable battery, let the engine idle a few minutes, and then from the positive (+) post of the discharged vehicle. start the engine in the vehicle with the discharged If frequent jump-starting is required to start your vehicle, battery. you should have the battery and charging system in6. Once the engine is started, remove the jumper cables spected at your authorized dealer. in the reverse sequence: CAUTION! Disconnecting The Jumper Cables 1. Disconnect the negative (-) jumper cable from the engine ground (-) of the vehicle with the discharged battery. 2. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. 3. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough without engine operation, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. I nf or mat i onPr ovi dedby: 6 342 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE CAUTION! (Continued) If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between DRIVE and REVERSE (with automatic transmission) or 2nd gear and REVERSE (with manual transmission), while gently pressing the accelerator. Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels, or racing the engine. NOTE: Press the #ESC Off# switch, to place the Electronic Stability Control (ESC) system in #Partial Off# mode, before rocking the vehicle. Refer to “Electronic Brake Control” in “Starting And Operating” for further information. Once the vehicle has been freed, press the #ESC Off# switch again to restore #ESC On# mode. CAUTION! CAUTION! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce • When “rocking” a stuck vehicle by shifting between DRIVE/2nd gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle. (Continued) I nf or mat i onPr ovi dedby: (Continued) WHAT TO DO IN EMERGENCIES 343 SHIFT LEVER OVERRIDE CAUTION! (Continued) • Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring). If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following procedure to temporarily move the shift lever: WARNING! 3. Remove the shift lever override access cover (located on the right side of the shift lever housing) by prying at the bottom edge of the cover. Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. 1. Turn the engine OFF. 2. Firmly apply the parking brake. I nf or mat i onPr ovi dedby: 6 344 WHAT TO DO IN EMERGENCIES 4. Press and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool into the access hole, and push and hold the override release lever in. 6. Move the shift lever to the NEUTRAL position. 7. The vehicle may then be started in NEUTRAL. 8. Reinstall the shift lever override access cover. Shift Lever Override Access Hole I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 345 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Flat Tow Wheel Lift Flatbed Wheels OFF The Ground NONE Rear Front ALL AUTOMATIC TRANSMISSION NOT ALLOWED NOT ALLOWED OK BEST METHOD I nf or mat i onPr ovi dedby: MANUAL TRANSMISSION If transmission is operable: • Transmission in NEUTRAL • 65 mph (104 km/h) max speed NOT ALLOWED OK BEST METHOD 6 346 WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets. State and local laws regarding vehicles under tow must be observed. Automatic Transmission • Vehicle can be towed with the front wheels elevated. • Vehicle can be towed on a flatbed truck (all wheels off the ground). If the ignition key is unavailable, or the battery is discharged, refer to “Shift Lever Override” in this section for instructions on shifting the transmission out of PARK If you must use the accessories (wipers, defrosters, etc.) in order to move the vehicle. while being towed, the ignition must be in the ON/RUN position. CAUTION! CAUTION! • Do not use sling-type equipment when towing. Vehicle damage may occur. • When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. • DO NOT flat tow any vehicle equipped with a conventional automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are OFF the ground. I nf or mat i onPr ovi dedby: (Continued) WHAT TO DO IN EMERGENCIES 347 CAUTION! (Continued) CAUTION! • Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. Towing this vehicle in violation of the above requirements can cause severe engine and/or transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. Manual Transmission ENHANCED ACCIDENT RESPONSE SYSTEM • Vehicle can be flat towed (all four wheels on the In the event of an impact causing airbag deployment, if ground) with the transmission in NEUTRAL. the communication network remains intact, and the • Vehicle can be towed with the front wheels elevated. power remains intact, depending on the nature of the event the ORC will determine whether to have the • Vehicle can be towed on a flatbed truck (all wheels off Enhanced Accident Response System perform the followthe ground). ing functions: • Cut off fuel to the engine. • Flash hazard lights as long as the battery has power or until the ignition key is turned off. I nf or mat i onPr ovi dedby: 6 348 WHAT TO DO IN EMERGENCIES • Turn on the interior lights, which remain on as long as In order to move your vehicle to the side of the road you the battery has power or until the ignition key is must follow the system reset procedure. removed. Customer Action Customer Will See • Unlock the doors automatically. 1. Turn ignition OFF. After the event occurs, when the system is active, the (Turn Signal Switch Must message #Fuel Cutoff See Handbook# is displayed. be placed in Neutral State). Carefully check the vehicle for fuel leaks in the engine 2. Turn ignition ON. Left Turn Light is OFF. compartment and on the ground near the engine comRight Turn Light partment and fuel tank before resetting the system and BLINKS. starting the engine. 3. Turn Right Turn Signal Right Turn Light is ON System Reset Procedure Switch ON. SOLID. Left Turn Light BLINKS. After an impact causing airbag deployment, the left and right turn signal lights, located in the instrument panel 4. Turn Left Turn Signal Left Turn Light is ON cluster, will both be blinking, until the ignition is turned Switch ON. SOLID. Right Turn Light off. BLINKS. I nf or mat i onPr ovi dedby: WHAT TO DO IN EMERGENCIES 349 Customer Action 5. Turn Right Turn Signal Switch ON. 6. Turn Left Turn Signal Switch ON. 7. Turn Left Turn Signal Switch OFF. (Turn Signal Switch Must be placed in Neutral State). Customer Will See Right Turn Light is ON SOLID. Left Turn Light BLINKS. Left Turn Light is ON SOLID. Right Turn Light is ON SOLID. Left Turn Light is OFF. Right Turn Light is OFF. Customer Action 8. Turn ignition OFF. Customer Will See System is now reset and the engine may be started. 9. Turn Hazard Flashers OFF (Manually). If a reset procedure step is not completed within 45 seconds, then the turn signal lights will turn off and the reset procedure must be performed again in order to be successful. I nf or mat i onPr ovi dedby: 6 I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE CONTENTS ! ENGINE COMPARTMENT — 1.4L . . . . . . . . . .353 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .362 ! ENGINE COMPARTMENT — 1.4L TURBO . . . .354 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .363 ! ONBOARD DIAGNOSTIC SYSTEM — OBD II . .355 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .365 ! EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS . . . . . . . . . . . . .356 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . .369 ! REPLACEMENT PARTS . . . . . . . . . . . . . . . . . .357 ! DEALER SERVICE . . . . . . . . . . . . . . . . . . . . . .357 ! MAINTENANCE PROCEDURES . . . . . . . . . . .358 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . .359 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . .362 ▫ Wiper Blades . . . . . . . . . . . . . . . . . . . . . . . .369 ▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . .372 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . .372 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . .375 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . .381 ▫ Manual Transmission — If Equipped . . . . . . .383 I nf or mat i onPr ovi dedby: 7 352 MAINTAINING YOUR VEHICLE ▫ Automatic Transmission — If Equipped . . . . .384 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .386 ▫ Front Turn Signal, Parking And Daytime Running Lamps. . . . . . . . . . . . . . . . . . . . . . .403 ▫ Front Fog Lamps . . . . . . . . . . . . . . . . . . . . . .403 ▫ Convertible Top Care — If Equipped . . . . . . .392 ▫ Front/Rear Side Marker Lamps. . . . . . . . . . . .403 ! FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .394 ▫ Rear Tail, Stop, Backup And Turn Signal Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . .404 ▫ Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . .395 ▫ Underhood Fuses. . . . . . . . . . . . . . . . . . . . . .397 ! VEHICLE STORAGE . . . . . . . . . . . . . . . . . . . .400 ! REPLACEMENT BULBS . . . . . . . . . . . . . . . . .401 ! BULB REPLACEMENT . . . . . . . . . . . . . . . . . .402 ▫ Headlamps Low Beam and High Beam . . . . . .402 ▫ Center High Mounted Stop Lamp (CHMSL). . .405 ! FLUID CAPACITIES . . . . . . . . . . . . . . . . . . . .406 ! FLUIDS, LUBRICANTS AND GENUINE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .407 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .407 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . .409 I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 353 ENGINE COMPARTMENT — 1.4L 7 1 2 3 4 — — — — Engine Coolant Reservoir Engine Oil Dipstick Brake Fluid Reservoir Front Distribution Unit (Fuses) 5 6 7 8 — Battery — Air Cleaner Filter — Engine Oil Fill — Washer Fluid Reservoir I nf or mat i onPr ovi dedby: 354 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 1.4L TURBO 1 2 3 4 — — — — Engine Coolant Reservoir Engine Oil Dipstick Brake Fluid Reservoir Front Distribution Unit (Fuses) 5 — Battery 6 — Engine Oil Fill 7 — Washer Fluid Reservoir I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 355 ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations. If any of these systems require service, the OBD II system will turn on the “Malfunction Indicator Light (MIL).” It will also store diagnostic codes and other information to assist your service technician in making repairs. Although your vehicle will usually be drivable and not need towing, see your authorized dealer for service as soon as possible. CAUTION! • Prolonged driving with the MIL on could cause further damage to the emission control system. It could also affect fuel economy and driveability. The vehicle must be serviced before any emissions tests can be performed. • If the MIL is flashing while the engine is running, severe catalytic converter damage and power loss will soon occur. Immediate service is required. I nf or mat i onPr ovi dedby: 7 356 MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station. To check if your vehicle’s OBD II system is ready, you must do the following: In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. 1. Cycle the ignition switch to the ON position, but do not crank or start the engine. Failure to pass could prevent vehicle registration. For states that require an Inspection and Mainte- NOTE: If you crank or start the engine, you will have to nance (I/M), this check verifies the “Malfunction start this test over. Indicator Light (MIL)” is functioning and is not 2. As soon as you cycle the ignition switch to the ON on when the engine is running, and that the OBD II position, you will see the Malfunction Indicator Light system is ready for testing. (MIL) symbol come on as part of a normal bulb check. Normally, the OBD II system will be ready. The OBD II 3. Approximately 15 seconds later, one of two things will system may not be ready if your vehicle was recently happen: serviced, recently had a dead battery or a battery replacement. If the OBD II system should be determined not • The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF ready for the I/M test, your vehicle may fail the test. the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 357 • The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is ready and you can proceed to the I/M station. REPLACEMENT PARTS Use of genuine parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance. Damage or failures caused by the If your OBD II system is not ready, you should see your use of parts which are not quality-equivalent to genuine authorized dealer or repair facility. If your vehicle was parts for maintenance and repairs will not be covered by recently serviced or had a battery failure or replacement, the manufacturer’s warranty. you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II DEALER SERVICE system to update. A recheck with the above test routine Your authorized dealer has the qualified service personmay then indicate that the system is now ready. nel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are Regardless of whether your vehicle’s OBD II system is available which include detailed service information for ready or not, if the MIL is illuminated during normal your vehicle. Refer to these Service Manuals before vehicle operation you should have your vehicle serviced attempting any procedure yourself. before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running. I nf or mat i onPr ovi dedby: 7 358 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. WARNING! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the future. CAUTION! • Failure to properly maintain your vehicle or perform repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle performance. Immediately have potential malfunctions examined by an authorized dealer or qualified repair center. • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty. If a flush is needed because of component malfunction, use only the specified fluid for the flushing procedure. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 359 Engine Oil CAUTION! Checking Oil Level Do not overfill the engine with oil. Overfilling the To assure proper engine lubrication, the engine oil must engine with oil will cause oil aeration, which can be maintained at the correct level. Check the oil level at lead to loss of oil pressure and an increase in oil regular intervals, such as every fuel stop. The best time to temperature. This loss of oil pressure and increased check the engine oil level is about five minutes after a oil temperature could damage your engine. fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Change Engine Oil Checking engine oil level when the engine is cold will The oil change indicator system will remind you that it is give you an incorrect reading. time to take your vehicle in for scheduled maintenance. Checking the oil while the vehicle is on level ground, and Refer to the “Maintenance Schedule” for further informaabout five minutes after a fully warmed engine is shut tion. off, will improve the accuracy of the oil level readings. NOTE: Under no circumstances should oil change inMaintain the oil level between the range markings on the tervals exceed 10,000 miles (16,000 km) or twelve dipstick. The safe range is indicated by a crosshatch zone. months, whichever occurs first. Adding 1 qt (1L) of oil when the reading is at the low end of the indicated range will result in the oil level at the full end of the indicator range. I nf or mat i onPr ovi dedby: 7 360 MAINTAINING YOUR VEHICLE Engine Oil Selection — 1.4L Engine American Petroleum Institute (API) Engine Oil For best performance and maximum protection under all Identification Symbol types of operating conditions, the manufacturer only This symbol means that the oil has recommends engine oils that are API Certified and meet been certified by the American the requirements of Chrysler Material Standard MS-6395. Petroleum Institute (API). The Engine Oil Selection — 1.4L Turbo Engine manufacturer only recommends For best performance and maximum protection under all API Certified engine oils. types of operating conditions, the manufacturer only recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-12991. CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 361 Engine Oil Viscosity — 1.4L Engine (SAE Grade) Engine Oil Viscosity — 1.4L Turbo Engine SAE 5W-30 engine oil recommended for all operating (SAE Grade) temperatures. This engine oil improves low temperature SAE 5W-40 full synthetic engine oil is recommended for all operating temperatures. This engine oil improves low starting and vehicle fuel economy. temperature starting and vehicle fuel economy. You may use synthetic engine oils provided the recommended oil quality requirements are met, and the recom- Lubricants which do not have both the engine oil certimended maintenance intervals for oil and filter changes fication mark and the correct SAE viscosity grade number should not be used. are followed. Lubricants which do not have both the engine oil certi- The engine oil filler cap also shows the recommended fication mark and the correct SAE viscosity grade num- engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartber should not be used. ment” in “Maintaining Your Vehicle” for further informaThe engine oil filler cap also shows the recommended tion. engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartment” in “Maintaining Your Vehicle” for further information. I nf or mat i onPr ovi dedby: 7 362 MAINTAINING YOUR VEHICLE Synthetic Engine Oils Engine Oil Filter You may use synthetic engine oils provided the recom- The engine oil filter should be replaced with a new filter mended oil quality requirements are met, and the recom- at every engine oil change. mended maintenance intervals for oil and filter changes Engine Oil Filter Selection are followed. This manufacturer’s engines have a full-flow type disposMaterials Added To Engine Oil able oil filter. Use a filter of this type for replacement. The The manufacturer strongly recommends against the addi- quality of replacement filters varies considerably. Only tion of any additives (other than leak detection dyes) to the high quality filters should be used to assure most efficient engine oil. Engine oil is an engineered product and its service. MOPAR® engine oil filters are high quality oil performance may be impaired by supplemental additives. filters and are recommended. Disposing Of Used Engine Oil And Oil Filters Engine Air Cleaner Filter Care should be taken in disposing of used engine oil and oil Refer to the “Maintenance Schedule” for the proper filters from your vehicle. Used oil and oil filters, indiscrimi- maintenance intervals. nately discarded, can present a problem to the environment. Contact your authorized dealer, service station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 363 Maintenance-Free Battery WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury. Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR® engine air cleaner filters are a high quality filter and are recommended. Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required. WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Refer to “Jump-Starting Procedures” in “What To Do In Emergencies” for further information. I nf or mat i onPr ovi dedby: (Continued) 7 364 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 Volts. Do not allow cable clamps to touch each other. • Battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after handling. • The battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented). • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. • If a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery. Do not use a “fast charger” to provide starting voltage. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 365 Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. WARNING! (Continued) • The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. WARNING! CAUTION! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Warranty Information Book, located on the DVD, for further warranty information. Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components. Such damage is not covered by the New Vehicle Limited Warranty. (Continued) I nf or mat i onPr ovi dedby: 7 366 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling R134a — If Equipped Refrigerant Recovery And Recycling HFO 1234yf — If Equipped R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment. HFO 1234yf Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product with a low GWP (Global Warming Potential). However, the manufacturer recommends that air conditioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment. NOTE: Use only manufacturer approved A/C system PAG compressor oil and refrigerants. NOTE: Use only manufacturer approved A/C system PAG compressor oil and refrigerants. A/C Air Filter WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 367 The A/C air filter is located in the fresh air inlet on the 2. Pull the console closeout cover rearward to disengage lower right of center console. Perform the following the front retaining tab and remove the cover. procedure to replace the filter: 1. Remove the Torx® screw that secures the passenger side console closeout cover. 7 Console Closeout Panel Torx® Screw Location I nf or mat i onPr ovi dedby: 368 MAINTAINING YOUR VEHICLE 3. Remove the two 5.5 mm screws (1 and 2) that secure the particulate air filter cover to the HVAC housing. A/C Air Filter 5. Install the A/C air filter with the air filter position indicators pointing in the same direction as removal. Air Filter Cover Screw Locations 4. Remove the A/C air filter by pulling it straight out of the housing. Take note of the air filter position indicators. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 369 CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 6. Install the passenger side console closeout. the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a Refer to the “Maintenance Schedule” for the proper year, preferably in the Fall and Spring. Apply a small maintenance intervals. amount of a high quality lubricant, such as MOPAR® Lock Cylinder Lubricant directly into the lock cylinder. Body Lubrication Locks and all body pivot points, including such items as Wiper Blades seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as MOPAR® Spray White Lube to assure quiet, easy operation and to protect against rust and wear. Prior to Clean the rubber edges of the wiper blades and the windshield and rear window periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt, waxes, or road film, and help reduce streaking and smearing. I nf or mat i onPr ovi dedby: 7 370 MAINTAINING YOUR VEHICLE Operation of the wipers on dry glass for long periods Rear Wiper Blade Removal/Installation may cause deterioration of the wiper blades. Always use 1. Lift the pivot cap on the rear wiper arm upward, this washer fluid when using the wipers to remove salt or dirt will allow the rear wiper blade to be raised off of the from a dry windshield or rear window. liftgate glass. Avoid using the wiper blades to remove frost or ice from the windshield or rear window. Make sure that they are not frozen to the glass before turning them on to avoid damaging the blade. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. NOTE: Life expectancy of wiper blades varies depending on geographical area and frequency of use. Poor performance of blades may be present with chattering, marks, water lines or wet spots. If any of these conditions are present, clean the wiper blades or replace as necessary. 1 — Wiper Arm 2 — Pivot Cap I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 371 NOTE: The rear wiper arm cannot be raised fully upward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. 1 2 3 4 — — — — Wiper Blade Blade Pivot Pin Wiper Arm Wiper Blade Holder I nf or mat i onPr ovi dedby: 7 372 MAINTAINING YOUR VEHICLE 4. Install the wiper blade pivot pin into the wiper blade Exhaust System holder at the end of the wiper arm, and firmly press The best protection against carbon monoxide entry into the wiper blade until it snaps into place. the vehicle body is a properly maintained engine exhaust 5. Lower the wiper blade and snap the pivot cap into system. place. If you notice a change in the sound of the exhaust system; Adding Washer Fluid or if the exhaust fumes can be detected inside the vehicle; The windshield washer fluid reservoir is located in the or when the underside or rear of the vehicle is damaged; engine compartment, and the fluid level should be checked have an authorized technician inspect the complete exat regular intervals. Fill the reservoir with windshield haust system and adjacent body areas for broken, damwasher solvent (not engine coolant/ antifreeze). Refer to aged, deteriorated, or mispositioned parts. Open seams “Engine Compartment” in “Maintaining Your Vehicle” for or loose connections could permit exhaust fumes to seep further information. into the passenger compartment. In addition, have the exhaust system inspected each time the vehicle is raised WARNING! for lubrication or oil change. Replace as required. Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 373 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle. I nf or mat i onPr ovi dedby: 7 374 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damverter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage. motion. NOTE: Intentional tampering with emissions control • Do not try to start the engine by pushing or towing the systems can result in civil penalties being assessed vehicle. against you. • Do not idle the engine with any spark plug wires In unusual situations involving grossly malfunctioning disconnected or removed, such as when diagnostic engine operation, a scorching odor may suggest severe testing, or for prolonged periods during very rough and abnormal catalyst overheating. If this occurs, stop idle or malfunctioning operating conditions. the vehicle, turn off the engine and allow it to cool. Service, including a tune-up to manufacturer’s specifications, should be obtained immediately. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 375 Coolant Checks Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (antifreeze). Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. I nf or mat i onPr ovi dedby: 7 376 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush And Refill CAUTION! NOTE: Some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized dealer. If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with OAT coolant (antifreeze) (conforming to MS.90032). Refer to the “Maintenance Schedule” for the proper maintenance intervals. Selection Of Coolant Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any “globally compatible” coolant (antifreeze). If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible. I nf or mat i onPr ovi dedby: (Continued) MAINTAINING YOUR VEHICLE 377 CAUTION! (Continued) • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. Adding Coolant Your vehicle has been built with an improved engine coolant (OAT coolant conforming to MS.90032) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to ten years or 150,000 miles (240,000 km) before replacement. To prevent reducing this extended maintenance period, it is important that you use the same engine coolant (OAT coolant conforming to MS.90032) throughout the life of your vehicle. Please review these recommendations for using Organic Additive Technology (OAT) engine coolant (antifreeze) that meets the requirements of Chrysler Material Standard MS.90032. When adding engine coolant (antifreeze): • We recommend using MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) that meets the requirements of Chrysler Material Standard MS.90032. • Mix a minimum solution of 50% OAT engine coolant that meets the requirements of Chrysler Material Standard MS.90032 and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below −34° F (−37° C) are anticipated. I nf or mat i onPr ovi dedby: 7 378 MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deion- • Mixing engine coolant (antifreeze) types is not recomized water when mixing the water/engine coolant mended and can result in cooling system damage. If HOAT and OAT coolant are mixed in an emergency, (antifreeze) solution. The use of lower quality water have a authorized dealer drain, flush, and refill with will reduce the amount of corrosion protection in the OAT coolant (conforming to MS.90032) as soon as engine cooling system. possible. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing ac- Cooling System Pressure Cap cording to the temperatures occurring in the area where The cap must be fully tightened to prevent loss of engine the vehicle is operated. coolant (antifreeze) and to ensure that engine coolant NOTE: (antifreeze) will return to the radiator from the coolant recovery tank. • Some vehicles require special tools to add coolant properly. Failure to fill these systems properly could The cap should be inspected and cleaned if there is any lead to severe internal engine damage. If any coolant is accumulation of foreign material on the sealing surfaces. needed to be added to the system please contact your local authorized dealer. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 379 WARNING! • Do not open hot engine cooling system. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result. engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. Coolant Level The coolant expansion bottle provides a quick visual method for determining that the coolant level is adequate. With the engine off and cold, the level of the engine coolant (antifreeze) in the bottle should be between the bottom and top lines marked “COLD FILL RANGE”. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a Used ethylene glycol-based engine coolant (antifreeze) is month. a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal When additional engine coolant (antifreeze) is needed to rules for your community. To prevent ingestion by ani- maintain the proper level, it should be added to the mals or children, do not store ethylene glycol-based coolant bottle. Do not overfill. Disposal Of Used Engine Coolant I nf or mat i onPr ovi dedby: 7 380 MAINTAINING YOUR VEHICLE • If frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested NOTE: When the vehicle is stopped after a few miles/ for leaks. kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- • Maintain engine coolant (antifreeze) concentration at a minimum of 50% OAT coolant (conforming to mally a result of moisture from rain, snow, or high MS.90032) and distilled water for proper corrosion prohumidity accumulating on the radiator and being vaportection of your engine which contains aluminum comized when the thermostat opens, allowing hot engine ponents. coolant (antifreeze) to enter the radiator. Points To Remember If an examination of your engine compartment shows no • Make sure that the coolant expansion bottle overflow hoses are not kinked or obstructed. evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the • Do not overfill the coolant expansion bottle. condenser clean. • Check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (antifreeze) • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY needs to be added, the contents of the coolant expansion the correct type thermostat. Other designs may result in bottle must also be protected against freezing. unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 381 Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the In order to assure brake system performance, all brake fluid level up to the requirements described on the brake system components should be inspected periodically. fluid reservoir. Fluid level can be expected to fall as the Refer to the “Maintenance Schedule” for the proper brake pads wear. The brake fluid level should be checked maintenance intervals. when the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Brake System WARNING! NOTE: If your vehicle is equipped with a manual transmission, the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in the reservoir, and a leak in one system will not affect the other system. The manual transmission clutch release system should not require fluid replacement during the life of the vehicle. If the brake fluid reservoir is low and the brake system does Brake Master Cylinder not indicate any leaks or other problems, it may be a The fluid level in the master cylinder should be checked result of a leak in the hydraulic clutch release system. See when performing under hood services, or immediately if your local authorized dealer for service. the “Brake Warning Light” is on. Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. Riding the brakes may also reduce braking capacity in an emergency. I nf or mat i onPr ovi dedby: 7 382 MAINTAINING YOUR VEHICLE Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. WARNING! • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also identified on the original factory installed hydraulic master cylinder reservoir. (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision. • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire. Brake fluid can also damage painted and vinyl surfaces, care should be taken to avoid its contact with these surfaces. (Continued) I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 383 Manual Transmission — If Equipped WARNING! (Continued) • Do not allow petroleum-based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Lubricant Selection Use only the manufacturers recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Fluid Level Check CAUTION! Use of improper brake fluids will affect overall clutch system performance. Improper brake fluids may damage the clutch system resulting in loss of clutch function and the ability to shift the transmission. Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16 in (4.7 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. I nf or mat i onPr ovi dedby: 7 384 MAINTAINING YOUR VEHICLE Frequency Of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless lubricant has become contaminated with water. NOTE: If contaminated with water, the fluid should be changed immediately. Automatic Transmission — If Equipped CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for fluid specifications. Special Additives Selection Of Lubricant The manufacturer strongly recommends against using any special additives in the transmission. It is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for fluid specifications. It is important to maintain the transmission fluid at the correct level using the recommended fluid. No chemical flushes should be used in any transmission; only the approved lubricant should be used. Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by supplemental additives. Therefore, do not add any fluid additives to the transmission. The only exception to this policy is the use of special dyes for diagnosing fluid leaks. Avoid using transmission sealers as they may adversely affect seals. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 385 CAUTION! CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe transmission damage may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid Level Check Fluid And Filter Changes The fluid level is preset at the factory and does not require adjustment under normal operating conditions. Routine fluid level checks are not required, therefore the transmission has no dipstick. Your authorized dealer can check your transmission fluid level using special service tools. If you notice fluid leakage or transmission malfunction, visit your authorized dealer immediately to have the transmission fluid level checked. Operating the vehicle with an improper fluid level can cause severe transmission damage. Under normal operating conditions, the fluid installed at the factory will provide satisfactory lubrication for the life of the vehicle. Routine fluid and filter changes are not required. However, change the fluid and filter if the fluid becomes contaminated (with water, etc.), or if the transmission is disassembled for any reason. I nf or mat i onPr ovi dedby: 7 386 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion What Causes Corrosion? Protection Of Body And Paint From Corrosion Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing The following maintenance recommendations will enable • Wash your vehicle regularly. Always wash your veyou to obtain maximum benefit from the corrosion hicle in the shade using MOPAR® Car Wash, or a mild resistance built into your vehicle. car wash soap, and rinse the panels completely with clear water. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 387 • If insects, tar, or other similar deposits have accumu- Special Care lated on your vehicle, use MOPAR® Super Kleen Bug • If you drive on salted or dusty roads or if you drive and Tar Remover to remove. near the ocean, hose off the undercarriage at least once a month. • Use a high quality cleaner wax, such as MOPAR® Cleaner Wax to remove road film, stains and to protect • It is important that the drain holes in the lower edges your paint finish. Take care never to scratch the paint. of the doors, rocker panels, and trunk be kept clear and open. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is CAUTION! considered the responsibility of the owner. • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. • If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. I nf or mat i onPr ovi dedby: 7 388 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, NOTE: If your vehicle is equipped with Dark Vapor or de-icer salt, etc., be sure that such materials are well Black Satin Chrome wheels DO NOT USE wheel cleaners, abrasives or polishing compounds. They will permapackaged and sealed. nently damage this finish and such damage is not cov• If a lot of driving is done on gravel roads, consider ered by the New Vehicle Limited Warranty. USE ONLY mud or stone shields behind each wheel. MILD SOAP AND WATER WITH A SOFT CLOTH. Used • Use MOPAR® Touch Up Paint on scratches as soon as on a regular basis this is all that is required to maintain possible. Your authorized dealer has touch up paint to this finish. match the color of your vehicle. CAUTION! Wheel And Wheel Trim Care • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s protective finish. Only MOPAR® Wheel Cleaner or equivalent is recommended. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 389 Stain Repel Fabric Cleaning Procedure — If Equipped Interior Care Use MOPAR® Total Clean to clean fabric upholstery and Stain Repel seats may be cleaned in the following man- carpeting. ner: Use MOPAR® Total Clean to clean vinyl upholstery. • Remove as much of the stain as possible by blotting MOPAR® Total Clean is specifically recommended for with a clean, dry towel. leather upholstery. • Blot any remaining stain with a clean, damp towel. Your leather upholstery can be best preserved by regular • For tough stains, apply MOPAR® Total Clean, or a cleaning with a damp soft cloth. Small particles of dirt mild soap solution to a clean, damp cloth and remove can act as an abrasive and damage the leather upholstery stain. Use a fresh, damp towel to remove soap residue. and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth • For grease stains, apply MOPAR® Multi-Purpose and MOPAR® Total Clean. Care should be taken to avoid Cleaner to a clean, damp cloth and remove stain. Use soaking your leather upholstery with any liquid. Please a fresh, damp towel to remove soap residue. do not use polishes, oils, cleaning fluids, solvents, deter• Do not use any harsh solvents or any other form of gents, or ammonia-based cleaners to clean your leather protectants on Stain Repel products. upholstery. Application of a leather conditioner is not required to maintain the original condition. I nf or mat i onPr ovi dedby: 7 390 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. CAUTION! To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces Do not use Alcohol and Alcohol-based and/or Keton based cleaning products to clean leather seats, as damage to the seat may result. All glass surfaces should be cleaned on a regular basis with MOPAR® Glass Cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear winCleaning Headlights dow equipped with electric defrosters or the right rear Your vehicle has plastic headlights that are lighter and quarter window equipped with the radio antenna. Do less susceptible to stone breakage than glass headlights. not use scrapers or other sharp instrument that may Plastic is not as scratch resistant as glass and therefore scratch the elements. different lens cleaning procedures must be followed. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 391 When cleaning the rear view mirror, spray cleaner on the Cleaning Plastic Instrument Cluster Lenses towel or rag that you are using. Do not spray cleaner The lenses in front of the instruments in this vehicle are directly on the mirror. molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. Instrument Panel Cover The instrument panel cover has a low glare surface which 1. Clean with a wet soft rag. A mild soap solution may be minimizes reflections on the windshield. Do not use used, but do not use high alcohol content or abrasive protectants or other products which may cause undesircleaners. If soap is used, wipe clean with a clean damp able reflections. Use soap and warm water to restore the rag. low glare surface. 2. Dry with a soft cloth. Instrument Panel Bezels Seat Belt Maintenance CAUTION! When installing hanging air fresheners in your vehicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Dry with a soft cloth. I nf or mat i onPr ovi dedby: 7 392 MAINTAINING YOUR VEHICLE Replace the belts if they appear frayed or worn or if the Convertible Top Care — If Equipped buckles do not work properly. NOTE: Lubricate the top rails with Berulub FR 43 every 2000 cycles or if scratching noises due to dust are present. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). CAUTION! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • Avoid high-pressure car washes, as they can damage the top material. Also, increased water pressure may force past the weather strips. • Remove any standing water from the top and dry the surface before opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicles interior. • Use care when washing the vehicle, water pressure directed at the weather strip seals may cause water to leak into the vehicles interior. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 393 Immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleanings easier. Do not subject the top to excessive heat. Frequently vacuum the top and storage compartment. General Cleaning Careful vacuuming of the top before washing is helpful in removing dust and other foreign particles. Wash in partial shade instead of direct sun. Wet the entire vehicle before washing the top. The top should be washed with a soft, natural bristle scrub brush, and a mild soap Washing solution such as liquid dishwashing soap. Do not use Hand washing is highly recommended. Automatic car detergent. washing equipment can damage the top material. If you must use an automatic car wash, soft cloth systems are CAUTION! preferred. Never use an abrasive type cleaner or bleaches. CAUTION! Cleaners should not contain silicones, organic solvents, petroleum distillates, or plasticizers. Always Avoid high-pressure car washes, as they can damage wait until the top is thoroughly dry before lowering the top material. Also, increased water pressure may it into the storage area. force water past the weather strips. I nf or mat i onPr ovi dedby: 7 394 MAINTAINING YOUR VEHICLE Scrub in all directions, covering an area of about two FUSES square feet at a time. Avoid heavy scrubbing. Rinse the entire vehicle with water to remove all soap and dirt from WARNING! the top fabric and to prevent streaking on painted and chrome surfaces. Allow the top to dry before lowering. • When replacing a blown fuse, always use an appropriate replacement fuse with the same amp rating as Vacuuming the top with a wet/dry shop vacuum will the original fuse. Never replace a fuse with another decrease the top’s drying time, ensure removal of all dirt, fuse of higher amp rating. Never replace a blown and delete streaks in the material. Multiple cleanings fuse with metal wires or any other material. Failure may be necessary to remove stubborn stains. If stains to use proper fuses may result in serious personal persist, contact your local authorized dealer for further injury, fire and/or property damage. suggestions. • Before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged. • If the replaced fuse blows again, contact an authorized dealer. (Continued) I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 395 WARNING! (Continued) • If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Interior Fuses The interior fuse panel is part of the Body Control Module (BCM) and is located on the driver’s side under the instrument panel. Fuse Panel Cavity 1 2 Vehicle Fuse Number F12 F32 Mini Fuse Description 7.5 Amp Brown 5 Amp Tan Right Low Beam Front and Rear Ceiling Lights Trunk and Door Courtesy Lights I nf or mat i onPr ovi dedby: 7 396 MAINTAINING YOUR VEHICLE Mini Fuse Description 3 4 5 6 7 8 9 10 Vehicle Fuse Number F53 F38 F36 F43 F48 F13 F50 F51 5 Amp Tan 20 Amp Yellow 10 Amp Red 20 Amp Yellow 20 Amp Yellow 7.5 Amp Brown 7.5 Amp Brown 5 Amp Tan 11 12 13 14 F37 F49 F31 F47 5 Amp Tan 5 Amp Tan 5 Amp Tan 20 Amp Yellow Instrument Panel Node Central Door Locking Diagnostic Socket, Car Radio, Climate Control System Bi-Directional Washer Passenger Power Window Left Low Beam, Headlamp Leveling Airbag Car Radio Switch, Climate Control System, Stop Light, Clutch Stop Light Switch, Instrument Panel Node Exterior Mirror, GPS, Electric Mirror, Parking Sensor Ignition, Climate Control Driver Power Window Cavity I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 397 The ID number of the electrical component correspondThe Front Distribution Unit is located on the right side of ing to each fuse can be found on the back of the cover. the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover. Underhood Fuses 7 Front Distribution Unit I nf or mat i onPr ovi dedby: 398 MAINTAINING YOUR VEHICLE Cavity F01 F02 F03 F04 F05 F06 F06 F07 F08 F09 F10 F11 F11 F14 F15 Maxi Fuse 60 Amp Blue 20 Amp Yellow 20 Amp Yellow 40 Amp Orange 70 Amp Tan 20 Amp Yellow 30 Amp Green 40 Amp Orange 40 Amp Orange – – – – – – Mini Fuse – – – – – – – – – 10 Amp Red 10 Amp Red 15 Amp Blue 10 Amp Red 5 Amp Tan 15 Amp Blue I nf or mat i onPr ovi dedby: Description Body Controller Audio Amplifier Ignition Switch Anti-Lock Brake Pump Electric Power Steering Radiator Fan - Single Speed Radiator Fan - Low Speed Radiator Fan - High Speed Blower Motor Powertrain Horn Powertrain Powertrain (Multiair – If Equipped) High Beam (Shutter) Cigar Lighter MAINTAINING YOUR VEHICLE 399 Cavity F16 F17 F17 F18 F18 F19 F20 F21 F22 F23 F24 F30 F82 F83 F84 Maxi Fuse – – – – – – – – – – – – 30 Amp Green 20 Amp Yellow – Mini Fuse 7.5 Amp Brown 25 Amp Clear 15 Amp Blue 15 Amp Blue 5 Amp Tan 7.5 Amp Brown 15 Amp Blue 15 Amp Blue 20 Amp Yellow 20 Amp Yellow 7.5 Amp Brown 15 Amp Blue – – 10 Amp Red I nf or mat i onPr ovi dedby: Description Transmission Powertrain (Multiair – If Equipped) Powertrain Powertrain Powertrain (Multiair – If Equipped) Air Conditioning Heated Seats – If Equipped Fuel Pump Powertrain Anti-Lock Brake Valves Stability Control System Fog Lamps Sunroof/Convertible Top Cooling Pump – If Equipped Transmission 7 400 MAINTAINING YOUR VEHICLE Cavity F85 F87 F90 Maxi Fuse 30 Amp Green (ATO) – – Mini Fuse – 5 Amp Tan 5 Amp Tan VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (e.g., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. I nf or mat i onPr ovi dedby: Description Rear Defroster Rear Defroster Heated Mirrors – If Equipped MAINTAINING YOUR VEHICLE 401 REPLACEMENT BULBS Interior Bulbs Bulb Number C5W W5W Overhead Lamp Courtesy Lamp Exterior Bulbs Bulb Number HIR2LL W21/5W H11LL W3W WY21W WY5W PY21W W3W Front Low and High Beam Headlamp Front Parking/Daytime Running Lamps Front Fog Lamps Front Side Marker Lamps Front Turn Signal Lamps Side Direction Lamps Rear Turn Signal Lamps Rear Side Marker Lamps I nf or mat i onPr ovi dedby: 7 402 MAINTAINING YOUR VEHICLE Bulb Number P21/5W W16W W5W LED (See Authorized dealer) Rear Tail and Stop Lamps Rear Backup Lamps Center High Mounted Stop Lamp License Plate Lamps NOTE: Numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your authorized dealer or refer to the applicable Service Manual. BULB REPLACEMENT Headlamps Low Beam and High Beam NOTE: Lens fogging can occur under certain atmo- 1. Remove the plastic cap from the back of the headlamp spheric conditions. This will usually clear as atmospheric housing. conditions change to allow the condensation to change 2. Rotate the bulb counter-clockwise. back into a vapor. Turning the lamps on will usually accelerate the clearing process. 3. Remove the bulb and replace as needed. 4. Install the bulb and rotate clockwise to lock in place. 5. Reinstall the plastic cap. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 403 Front Turn Signal, Parking And Daytime Running Lamps 3. Remove the plastic cap from the back of the lamp housing. 1. Turn the steering wheel completely to the left or right. 4. Rotate bulb/socket counter-clockwise. 2. Open the wheel housing access door. 5. Remove the bulb and replace as needed. 6. Install the bulb into socket, and rotate bulb/socket clockwise into lamp locking it in place. 7. Reinstall the plastic cap. Front Fog Lamps To replace the front fog lights, see your authorized dealer. Front/Rear Side Marker Lamps 1. Remove portion of the wheel liner to allow hand access to side marker lamp. Wheel Housing Access Door 2. Rotate the bulb socket counterclockwise, and remove the bulb and socket assembly from the housing. I nf or mat i onPr ovi dedby: 7 404 MAINTAINING YOUR VEHICLE 3. Pull the bulb from the socket and insert the replacement bulb. 4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. 5. Reinstall the wheel liner. Rear Tail, Stop, Backup And Turn Signal Lamps 1. Open the liftgate. 2. Remove the two screws and remove the tail lamp assembly. Tail Lamp Assembly Screws 3. Remove four screws and separate the backplate from the lamp housing. I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 405 4. Remove the tail, stop, or turn signal bulbs by pushing 3. them slightly and turning counter-clockwise. 4. 5. Remove the backup lamp bulb by pulling straight out. 5. 6. Replace lamps as required and reinstall lamp. Disconnect the electric connector. Press the retaining device and open the bulb holder. Remove the snap-fitted bulb to be replaced and replace it. 6. Close the back cap locking it properly. Center High Mounted Stop Lamp (CHMSL) 1. Remove the two guard caps and the two fastening 7. Reinstall the two fastening screws and reinstall the screws. guard caps. 2. Remove the center high mounted stop lamp assembly. 7 I nf or mat i onPr ovi dedby: 406 MAINTAINING YOUR VEHICLE FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 1.4L/1.4L Turbo Engine Cooling System 1.4L/1.4L Turbo Engine (MOPAR® Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula) — with Manual Transmission 1.4L/1.4L Turbo Engine (MOPAR® Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula) — with Automatic Transmission I nf or mat i onPr ovi dedby: U.S. 10.5 Gallons Metric 40 Liters 4 Quarts 3.8 Liters 4.6 Quarts 4.4 Liters 5.8 Quarts 5.5 Liters MAINTAINING YOUR VEHICLE 407 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant - 1.4L/1.4L Turbo Engine Engine Oil - 1.4L Engine Engine Oil - 1.4L Turbo Engine Engine Oil Filter - 1.4L/1.4L Turbo Engine Spark Plugs - 1.4L Engine Spark Plugs - 1.4L Turbo Engine Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/ 150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of Chrysler Material Standard MS-90032. We recommend you use API Certified SAE 5W-30 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. Use API Certified SAE 5W-40 Full Synthetic Engine Oil, meeting the requirements of Chrysler Material Standard MS-12991. Refer to your engine oil filler cap for correct SAE grade. We recommend you use a MOPAR® Engine Oil Filter. We recommend you use MOPAR® Spark Plugs We recommend you use MOPAR® Spark Plugs I nf or mat i onPr ovi dedby: 7 408 MAINTAINING YOUR VEHICLE Component Fuel Selection - 1.4L/1.4L Turbo Engine Fluid, Lubricant, or Genuine Part 87 Octane Acceptable — 91 Octane Recommended CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any “globally compatible” coolant (antifreeze). If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS.90032), by an authorized dealer as soon as possible. • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. (Continued) I nf or mat i onPr ovi dedby: MAINTAINING YOUR VEHICLE 409 Chassis Component Manual Transmission – If Equipped Automatic Transmission – If Equipped Brake Master Cylinder Convertible Top Rails – If Equipped Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® C635 DDCT/MTX Transmission Fluid Use only MOPAR® AW-1 Automatic Transmission Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. We recommend you use MOPAR® DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. We recommend you use Berulub FR 43. 7 I nf or mat i onPr ovi dedby: I nf or mat i onPr ovi dedby: M A I N T E N A ▫ Maintenance Chart . . . . . . . . . . . . . . . . . . . .414 N C E MAINTENANCE SCHEDULES CONTENTS ! MAINTENANCE SCHEDULE . . . . . . . . . . . . .412 S C H E D U L E S 8 I nf or mat i onPr ovi dedby: M A I N T E N A N C E S C H E D U L E S 8 412 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This means that service is required for your vehicle. Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures, and E85 fuel usage will influence when the “Change Oil” or “Oil Change Required” message is displayed. Severe Operating Conditions can cause the change oil message to illuminate as early as 3,500 miles (5,600 km) since last reset. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km). Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. NOTE: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or twelve months, whichever comes first. Severe Duty All Models Change Engine Oil at 4,000 miles (6,500 km) if the vehicle is operated in a dusty and off road environment. This type of vehicle use is considered Severe Duty. I nf or mat i onPr ovi dedby: MAINTENANCE SCHEDULES 413 M Once A Month Or Before A Long Trip: Check engine oil level. Check windshield washer fluid level. Check the tire inflation pressures and look for unusual wear or damage. Check the fluid levels of the coolant reservoir and brake master cylinder, and fill as needed. Check function of all interior and exterior lights. Required Maintenance Intervals Refer to the maintenance schedules on the following page for the required maintenance intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: Change oil and filter. Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. Inspect battery and clean and tighten terminals as required. Inspect brake pads, rotors, and hoses. Inspect engine cooling system protection and hoses. Check and adjust hand brake. Inspect exhaust system. Inspect engine air cleaner if using in dusty or off-road conditions. I nf or mat i onPr ovi dedby: A I N T E N A N C E S C H E D U L E S 8 8 Maintenance Chart Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends and boot seals, and replace if necessary. Inspect the brake linings. Replace as necessary. 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 2 3 4 5 6 7 8 9 10 11 12 13 14 15 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 Or Years: Or Kilometers: 30,000 Mileage or time passed (whichever comes first) 48,000 Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. 20,000 S C H E D U L E S 414 MAINTENANCE SCHEDULES 32,000 M A I N T E N A N C E X X X X X X X X X X X X X X X X X X X I nf or mat i onPr ovi dedby: Inspect parking brake function. Adjust as necessary. Additional Maintenance Replace engine air filter. Replace cabin air filter. Clean and lube sun roof tracks. Replace spark plugs (1.4L Engine). ** Replace spark plugs (1.4L Turbo Engine). ** 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 2 3 4 5 6 7 8 9 10 11 12 13 14 15 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 Or Years: Or Kilometers: 20,000 Mileage or time passed (whichever comes first) 32,000 MAINTENANCE SCHEDULES 415 M X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X I nf or mat i onPr ovi dedby: X A I N T E N A N C E S C H E D U L E S 8 X X S C H E D U L E S 8 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 3 4 5 6 7 8 9 10 11 12 13 14 15 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 32,000 20,000 M 416 MAINTENANCE SCHEDULES A I Mileage or time passed N (whichever comes first) T E N Or Years: 2 A Or Kilometers: N C E Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Inspect and replace PCV valve if necessary. Replace the timing belt. X X X X ** The spark plug change interval is mileage based only, yearly intervals do not apply. I nf or mat i onPr ovi dedby: MAINTENANCE SCHEDULES 417 M WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident. A I N T E N A N C E S C H E D U L E S 8 I nf or mat i onPr ovi dedby: I nf or mat i onPr ovi dedby: IF YOU NEED CONSUMER ASSISTANCE CONTENTS ! SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .421 ▫ Prepare For The Appointment. . . . . . . . . . . . .421 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .421 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .423 ! WARRANTY INFORMATION . . . . . . . . . . . . .424 ! REPORTING SAFETY DEFECTS . . . . . . . . . . . .424 ▫ Be Reasonable With Requests . . . . . . . . . . . . .421 ▫ In The 50 United States And Washington, D.C.. . . . . . . . . . . . . . . . . . . . . .424 ! IF YOU NEED ASSISTANCE . . . . . . . . . . . . . .421 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . .425 ▫ FIAT Customer Center . . . . . . . . . . . . . . . . . .422 ! PUBLICATION ORDER FORMS . . . . . . . . . . . .425 ▫ FIAT Canada Customer Center . . . . . . . . . . . .422 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . .423 I nf or mat i onPr ovi dedby: 9 420 IF YOU NEED CONSUMER ASSISTANCE ! DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . .426 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .427 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .427 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .428 I nf or mat i onPr ovi dedby: IF YOU NEED CONSUMER ASSISTANCE 421 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment. If you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the IF YOU NEED ASSISTANCE current problem. The manufacturer and its authorized dealer are vitally Prepare A List interested in your satisfaction. We want you to be happy Make a written list of your vehicle’s problems or the with our products and services. specific work you want done. If you’ve had an accident Warranty service must be done by an authorized dealer. or work done that is not on your maintenance log, let the We strongly recommend that you take the vehicle to an service advisor know. authorized dealer. They know your vehicle the best, and I nf or mat i onPr ovi dedby: 9 422 IF YOU NEED CONSUMER ASSISTANCE are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. Any communication to the manufacturer’s customer center should include the following information: • Owner’s name and address • Owner’s telephone number (home and office) This is why you should always talk to an authorized • Authorized dealer name dealer service manager first. Most matters can be re- • Vehicle Identification Number (VIN) solved with this process. • Vehicle delivery date and mileage • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer. FIAT Customer Center They want to know if you need assistance. P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: • If an authorized dealer is unable to resolve the con- 1–800–423–6343 cern, you may contact the manufacturer’s customer FIAT Canada Customer Center center. P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: 1–800–465–2001 (English) Phone: 1–800–387–9983 (French) I nf or mat i onPr ovi dedby: IF YOU NEED CONSUMER ASSISTANCE 423 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY. Warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufacturer’s service contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of the vehicle delivery date. If you have any questions about the service contract, call the manufacturer’s Service Contract National Customer Hotline at 1-800-521-9922 (Canadian residents, call (800) 465–2001 English / (800) 387–9983 French). The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Service Contract Vehicle Limited Warranty expires, please refer to the You may have purchased a service contract for a vehicle contract documents, and contact the person listed in to help protect you from the high cost of unexpected those documents. repairs after the manufacturer’s New Vehicle Limited Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1-800-855-0511 to connect with a Bell Relay Service operator. I nf or mat i onPr ovi dedby: 9 424 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You will be pleased with their sincere efforts to resolve any warranty issues or related concerns. WARRANTY INFORMATION See the Warranty Information Booklet, located on the DVD, for the terms and provisions of FIAT Group Automobiles warranties applicable to this vehicle and market. REPORTING SAFETY DEFECTS In The 50 United States And Washington, D.C. WARNING! Engine exhaust (internal combustion engines only), some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy I nf or mat i onPr ovi dedby: IF YOU NEED CONSUMER ASSISTANCE 425 campaign. However, NHTSA cannot become involved in PUBLICATION ORDER FORMS individual problems between you, your authorized To order the following manuals, you may use either the dealer, and the manufacturer. website or the phone numbers listed below. Visa, MasTo contact NHTSA, you may either call the Auto Safety tercard, American Express, and Discover orders are acHotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), cepted. If you prefer mailing your payment, please call or go to http://www.safercar.gov; or write to: Admin- for an order form. istrator, NHTSA, 1200 New Jersey Avenue, SE., West NOTE: A street address is required when ordering Building, Washington, D.C. 20590. You can also obtain manuals (no P.O. Boxes). other information about motor vehicle safety from http://www.safercar.gov. Service Manuals In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately. Canadian customers who wish to report a safety defect to the Canadian government should contact Transport Canada, Motor Vehicle Defect Investigations and Recalls at 1-800-333-0510 or go to http://www.tc.gc.ca/ roadsafety/ These comprehensive Service Manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing FIAT Group Automobiles vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts. I nf or mat i onPr ovi dedby: 9 426 IF YOU NEED CONSUMER ASSISTANCE Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-by-step troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment. Owner’s Manuals These Owner’s Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FIAT Group Automobiles vehicles. Included are starting, operating, emergency and maintenance procedures as well as specifications, capabilities and safety tips. • Call toll free at: 1–800–890–4038 (U.S.) 1–800–387–1143 (Canada) Or • Visit us on the Worldwide Web at: www.techauthority.com DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. All passenger car tires must conform to Federal safety requirements in addition to these grades. I nf or mat i onPr ovi dedby: IF YOU NEED CONSUMER ASSISTANCE 427 Treadwear Traction Grades The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire’s ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. 9 I nf or mat i onPr ovi dedby: 428 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance, which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law. WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. I nf or mat i onPr ovi dedby: INDEX 10 I nf or mat i onPr ovi dedby: 430 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .377 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . .372 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .301 Air bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Air Bag Air bag Operation . . . . . . . . . . . . . . . . . . . . . . .42 Air Bag Warning Light . . . . . . . . . . . . . . . . . . . .51 Driver Knee Air Bag . . . . . . . . . . . . . . . . . . . . . .43 Enhanced Accident Response . . . . . . . . . . . . . . . .49 Event Data Recorder (EDR) . . . . . . . . . . . . . . . . .54 Front Air Bag . . . . . . . . . . . . . . . . . . . . . . . . . . .39 If A Deployment Occurs . . . . . . . . . . . . . . . . . . .48 Knee Impact Bolsters . . . . . . . . . . . . . . . . . . . . .43 Maintaining Your Air Bag System . . . . . . . . . . . .53 Air bag Deployment . . . . . . . . . . . . . . . . . . . . . . . .39 Air bag Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Air bag Maintenance. . . . . . . . . . . . . . . . . . . . . . . .53 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . .362 Air Conditioner Maintenance . . . . . . . . . . . . . . . . .365 Air Conditioning. . . . . . . . . . . . . . . . . . . . . . . . . .211 Air Conditioning Controls . . . . . . . . . . . . . . . . . . .211 Air Conditioning Filter . . . . . . . . . . . . . . . . . . . . .366 Air Conditioning, Operating Tips . . . . . . . . . . . . . .219 Air Conditioning Refrigerant . . . . . . . . . . . . . . . . .365 Air Conditioning System . . . . . . . . . . . . . . . . . . . .211 Air Pressure, Tires. . . . . . . . . . . . . . . . . . . . . . . . .275 Alterations/Modifications, Vehicle . . . . . . . . . . . . . . .8 Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . . . .376 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . .406 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .379 Anti-Lock Brake System (ABS) . . . . . . . . . . . . . . . .252 Anti-Lock Warning Light . . . . . . . . . . . . . . . . . . . .153 Appearance Care . . . . . . . . . . . . . . . . . . . . . . . . .386 Automatic Dimming Mirror. . . . . . . . . . . . . . . . . . .88 Automatic Oil Change Indicator . . . . . . . . . . . . . . .412 Automatic Temperature Control (ATC) . . . . . . . . . .213 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . . . . .11 I nf or mat i onPr ovi dedby: INDEX 431 Automatic Transmission . . Adding Fluid . . . . . . . . Fluid and Filter Changes Fluid Change . . . . . . . . Fluid Level Check . . . . . Fluid Type . . . . . . . . . . Gear Ranges . . . . . . . . . Special Additives . . . . . Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .233 .385 .385 .385 .385 .409 .237 .384 .242 Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .381 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . .252 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . . . . .252 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . .381 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .248 Warning Light . . . . . . . . . . . . . . . . . . . . . . . . .151 Brake/Transmission Interlock . . . . . . . . . . . . . . . . .235 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . .401 Bulbs, Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .363 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . .337 Keyless Transmitter Replacement (RKE) . . . . . . . .16 Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Body Mechanism Lubrication . . . . . . . . . . . . . . . . .369 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . . .268 Brake Assist System . . . . . . . . . . . . . . . . . . . . . . .254 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .407 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . . .248 Capacities, Antifreeze (Engine Coolant) . . . . . . . . . .406 Capacities, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .406 Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .361 Carbon Monoxide Warning . . . . . . . . . . . . . . . . . . .76 Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . .136 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .386 CD (Compact Disc) Player . . . . . . . . . . . . . . . . . . .180 I nf or mat i onPr ovi dedby: 10 432 INDEX Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . .210 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .286 Change Oil Indicator . . . . . . . . . . . . . . . . . . . . . . .412 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . . .324 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . . .262 Check Engine Light (Malfunction Indicator Light) . .149 Checking Your Vehicle For Safety . . . . . . . . . . . . . . .75 Checks, Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Child Restraints Booster Seats . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Child Restraints . . . . . . . . . . . . . . . . . . . . . . . . .55 Child Seat Installation . . . . . . . . . . . . . . . . . . . . .71 How To Stow An Unused ALR Seat Belt . . . . . . . .68 Infants And Child Restraints . . . . . . . . . . . . . . . .58 Install A LATCH-compatible Child Restraint . . . . .67 Installing Child Restraints Using The Vehicle Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 Lower Anchors And Tethers For Children . . . . . . .62 Older Children And Child Restraints . . . . . . . . . .59 Seating Positions . . . . . . . . . . . . . . . . . . . . . . . .61 Clean Air Gasoline . . . . . . . . . . . . . . . . . . . . . . . .299 Cleaning Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .388 Windshield Wiper Blades . . . . . . . . . . . . . . . . . .369 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . .210 Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .381 Clutch Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .381 Compact Disc (CD) Maintenance . . . . . . . . . . . . . .209 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . . .280 Connector UCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .207 Universal Consumer Interface (UCI) . . . . . . . . . .207 Contract, Service . . . . . . . . . . . . . . . . . . . . . . . . . .423 Convertible Top Maintenance . . . . . . . . . . . . . . . . .392 Coolant (Antifreeze) . . . . . . . . . . . . . . . . . . . . . . .406 Cooling System. . . . . . . . . . . . . . . . . . . . . . . . . . .375 Adding Coolant (Antifreeze) . . . . . . . . . . . . . . .377 I nf or mat i onPr ovi dedby: INDEX 433 Coolant Capacity . . . . . . . . . . . Coolant Level . . . . . . . . . . . . . . Disposal of Used Coolant . . . . . Drain, Flush, and Refill . . . . . . . Inspection . . . . . . . . . . . . . . . . Points to Remember . . . . . . . . . Pressure Cap . . . . . . . . . . . . . . Selection of Coolant (Antifreeze) . Corrosion Protection . . . . . . . . . . . Cruise Light . . . . . . . . . . . . . . . . . Cupholders . . . . . . . . . . . . . . . . . Customer Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .407 .375 .379 .376 .379 .378 .378 .376 .386 .157 .134 .421 Data Recorder, Event . . . . . . . . . . . . . . . . . . . . . . .54 Daytime Running Lights . . . . . . . . . . . . . . . . . . . .110 Dealer Service. . . . . . . . . . . . . . . . . . . . . . . . . . . .357 Defroster, Windshield . . . . . . . . . . . . . . . . . . . . . . .77 Diagnostic System, Onboard . . . . . . . . . . . . . . . . .355 Dipsticks Automatic Transmission . . . . . . . . . . . . . . . . . .385 Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . .379 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . . .21 Downshifting . . . . . . . . . . . . . . . . . . . . . . . . . . . .233 Driving Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .245 Electrical Power Outlets. . . . . . . . . . . . . . . . . . . . .131 Electric Remote Mirrors. . . . . . . . . . . . . . . . . . . . . .89 Electronic Brake Control System . . . . . . . . . . . . . . .252 Brake Assist System . . . . . . . . . . . . . . . . . . . . .254 Electronic Speed Control (Cruise Control) . . . . . . . .118 Electronic Stability Control (ESC) . . . . . . . . . . . . . .257 Electronic Vehicle Information Center (EVIC) . . . . . .159 Exit Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166 I nf or mat i onPr ovi dedby: 10 434 INDEX New Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 Start Of Trip Procedure . . . . . . . . . . . . . . . . . . .166 Trip Computer . . . . . . . . . . . . . . . . . . . . . . . . .165 Trip Functions . . . . . . . . . . . . . . . . . . . . . . . . .166 Emergency, In Case of Hazard Warning Flasher . . . . . . . . . . . . . . . . . .311 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .324 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . .337 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .345 Emission Control System Maintenance . . . . . . . . . .356 Engine Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .362 Break-In Recommendations . . . . . . . . . . . . . . . . .74 Checking Oil Level . . . . . . . . . . . . . . . . . . . . . .359 Compartment . . . . . . . . . . . . . . . . . . . . . . . . . .353 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .375 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . . . .76 Fails to Start . . . . . . . . . . . . . . . . . . . . . . . . . . .229 Flooded, Starting . . . . . . . . . . . . . . . . . . . . . . .229 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . .298 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .359 Oil Filler Cap . . . . . . . . . . . . . . . . . . . . . . . . . .361 Oil Selection . . . . . . . . . . . . . . . . . . . . . . . . . . .360 Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . .362 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . .311 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 Enhanced Accident Response Feature . . . . . . . . . . . .49 Euro Twin Clutch Transmission Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . . . .384 Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . . .54 Exhaust Gas Caution. . . . . . . . . . . . . . . . . . . . . . . .76 Exhaust System . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .362 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . .366 Engine Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .407 I nf or mat i onPr ovi dedby: INDEX 435 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .362 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . .362 Flashers Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . .229 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .409 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . .406 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Fluid Level Checks Automatic Transmission . . . . . . . . . . . . . . . . . .385 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .407 Fluids, Lubricants and Genuine Parts . . . . . . . . . . .407 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . . . .342 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .298 Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303 Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . . .301 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .406 Clean Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . .299 Filler Cap (Gas Cap) Gasoline . . . . . . . . . Light . . . . . . . . . . . Materials Added . . . Octane Rating . . . . . Requirements . . . . . Specifications . . . . . Tank Capacity . . . . . Fueling . . . . . . . . . . . Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303 .298 .156 .301 .299 .298 .407 .406 .303 .394 Gas Cap (Fuel Filler Cap) . Gasoline, Clean Air . . . . . . Gasoline (Fuel) . . . . . . . . . Gasoline, Reformulated . . . Gauges Odometer . . . . . . . . . . . Gear Ranges . . . . . . . . . . . Gear Select Lever Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303 .299 .298 .299 I nf or mat i onPr ovi dedby: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 . . . . . . . . . . . . . . . . . .237 . . . . . . . . . . . . . . . . . .343 10 436 INDEX Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 General Information . . . . . . . . . . . . . . . . . . . . . . .298 General Maintenance. . . . . . . . . . . . . . . . . . . . . . .358 Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . . .11 Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .390 Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . .13 Information Center, Vehicle . . . . . . . . . . . . . . . . . .159 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . .142 Hazard Instrument Panel and Controls . . . . . . . . . . . . . . . .141 Driving Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . . . . .245 Instrument Panel Cover . . . . . . . . . . . . . . . . . . . . .391 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 Instrument Panel Lens Cleaning . . . . . . . . . . . . . . .391 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .390 Interior Appearance Care . . . . . . . . . . . . . . . . . . . .389 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Interior Lighting . . . . . . . . . . . . . . . . . . . . . . . . . .111 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Heated Mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Heated Seats. . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 Jacking Instructions . . . . . . . . . . . . . . . . . . . . . . . .329 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211 Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . . .325 Hill Start Assist. . . . . . . . . . . . . . . . . . . . . . . . . . .255 Jack Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .324 Holder, Cup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . .337 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 Key-In Reminder . . . . . . . . . . . . . . . . . . . . . . . . . .13 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Key, Replacement . . . . . . . . . . . . . . . . . . . . . . . . . .14 I nf or mat i onPr ovi dedby: INDEX 437 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Key, Sentry (Immobilizer) . . . . . . . . . . . . . . . . . . . .13 Lane Change Assist . . . . . . . . . . . . . . . . . . . . . . . .111 Lap/Shoulder Belts. . . . . . . . . . . . . . . . . . . . . . . . .28 Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . . .298 Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 Liftgate (Sedan) . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153 Brake Assist Warning . . . . . . . . . . . . . . . . . . . .260 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . .151 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . .402 Check Engine (Malfunction Indicator) . . . . . . . . .149 Engine Temperature Warning . . . . . . . . . . . . . . .158 Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 High Beam Indicator . . . . . . . . . . . . . . . . . . . . .148 Low Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . .158 Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . .149 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .402 Tire Pressure Monitoring (TPMS) . . . . . . . . . . . .145 Traction Control . . . . . . . . . . . . . . . . . . . . . . . .260 Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157 Warning (Instrument Cluster Description) . . . . . .145 Loading Vehicle Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .268 I nf or mat i onPr ovi dedby: 10 438 INDEX Media Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 Locks Automatic Door . . . . . . . . . . . . . . . . . . . . . . . . .21 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 Automatic Dimming . . . . . . . . . . . . . . . . . . . . . .88 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Electric Powered . . . . . . . . . . . . . . . . . . . . . . . . .89 Power Door . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . . .369 Lug Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323 Modifications/Alterations, Vehicle . . . . . . . . . . . . . . .8 Monitor, Tire Pressure System . . . . . . . . . . . . . . . .288 Maintenance Free Battery. . . . . . . . . . . . . . . . . . . .363 Multi-Function Control Lever . . . . . . . . . . . . . . . . .108 Maintenance, General . . . . . . . . . . . . . . . . . . . . . .358 Maintenance Procedures . . . . . . . . . . . . . . . . . . . .358 New Vehicle Break-In Period . . . . . . . . . . . . . . . . . .74 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . .412 Maintenance Schedules . . . . . . . . . . . . . . . . . . . . .412 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . .25 Malfunction Indicator Light (Check Engine). . . . . . .356 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . . .299 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . .425 Odometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Manual Transmission . . . . . . . . . . . . . . . . . . . . . .230 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . .383 Oil Change Indicator . . . . . . . . . . . . . . . . . . . . . . .164 Frequency of Fluid Change . . . . . . . . . . . . . . . .384 Oil Change Indicator, Reset . . . . . . . . . . . . . . . . . .164 Lubricant Selection . . . . . . . . . . . . . . . . . . . . . .383 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .359 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .406 Master Cylinder (Brakes) . . . . . . . . . . . . . . . . . . . .381 I nf or mat i onPr ovi dedby: INDEX 439 Change Interval . . . . . . . . . . . . . . . . . . . . . . . .359 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .359 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .362 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .362 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . .362 Identification Logo . . . . . . . . . . . . . . . . . . . . . .360 Materials Added to . . . . . . . . . . . . . . . . . . . . . .362 Recommendation . . . . . . . . . . . . . . . . . . . . . . .360 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .362 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .361 Oil Filter, Selection . . . . . . . . . . . . . . . . . . . . . . . .362 Onboard Diagnostic System . . . . . . . . . . . . . . . . . .355 Operating Precautions . . . . . . . . . . . . . . . . . . . . . .355 Operator Manual (Owner’s Manual) . . . . . . . . . . . . .5 Overheating, Engine . . . . . . . . . . . . . . . . . . . . . . .155 Owner’s Manual (Operator Manual) . . . . . . . . . . . . .5 Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Pets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 Placard, Tire and Loading Information . . . . . . . . . .269 Power Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . . .131 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .247 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Pregnant Women and Seat Belts . . . . . . . . . . . . . . . .35 Preparation for Jacking . . . . . . . . . . . . . . . . . . . . .328 Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Radial Ply Tires . . . . . Radio Operation . . . . . Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .386 Radio Reception . . . . . Parking Brake. . . . . . . . . . . . . . . . . . . . . . . . . . . .248 Radio (Sound Systems) I nf or mat i onPr ovi dedby: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .276 .180 .180 .180 10 440 INDEX Rear Liftgate (Sedan) . . . . . . . . . . . . . . . . . . . . . . .24 Rear Window Features . . . . . . . . . . . . . . . . . . . . .137 Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . .54 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . .306 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . .299 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .366 Release, Hood. . . . . . . . . . . . . . . . . . . . . . . . . . . .106 Remote Keyless Entry (RKE) FCC General Information . . . . . . . . . . . . . . . . . .18 Remote Sound System (Radio) Controls . . . . . . . . .208 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . .401 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . .14 Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . .357 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . . .284 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . .424 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Restraints, Occupant . . . . . . . . . . . . . . . . . . . . . . . .25 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . .287 Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . . .77 Safety Checks Outside Vehicle . . . . . . . . . . . . . . . . .79 Safety Defects, Reporting . . . . . . . . . . . . . . . . . . . .424 Safety, Exhaust Gas. . . . . . . . . . . . . . . . . . . . . . . . .76 Safety Information, Tire . . . . . . . . . . . . . . . . . . . . .261 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . .412 Seat Belt Disengage The Automatic Locking Mode . . . . . . .38 Energy Management Feature . . . . . . . . . . . . . . . .35 Engage The Automatic Locking Mode . . . . . . . . .38 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . .28 Lap/Shoulder Belt Untwisting . . . . . . . . . . . . . . .33 Pregnant Women . . . . . . . . . . . . . . . . . . . . . . . .35 Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . . .34 Seat Belt Pretensioner . . . . . . . . . . . . . . . . . . . . .35 Seat Belt System . . . . . . . . . . . . . . . . . . . . . . . . .25 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . . .391 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 I nf or mat i onPr ovi dedby: INDEX 441 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . . .55 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Operating Instructions . . . . . . . . . . . . . . . . . . . .31 Pregnant Women . . . . . . . . . . . . . . . . . . . . . . . .35 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149 Untwisting Procedure . . . . . . . . . . . . . . . . . . . . .33 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 SENTRY KEY® FCC General Information . . . . . . . . . . . . . . . . . .15 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . . .13 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . . .421 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . .423 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . . .425 Shift Lever Override . . . . . . . . . . . . . . . . . . . . . . .343 Shift Speeds, Manual Transmission . . . . . . . . . . . . .232 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Signals, Turn . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . . .286 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .278 Spare Tire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .280 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .407 Speed Control (Cruise Control). . . . . . . . . . . . . . . .118 Sport Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 Automatic Transmission . . . . . . . . . . . . . . . . . .227 Cold Weather . . . . . . . . . . . . . . . . . . . . . . . . . .228 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . .229 Manual Transmission . . . . . . . . . . . . . . . . . . . .227 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .247 Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . . . .117 Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 I nf or mat i onPr ovi dedby: 10 442 INDEX Steering Wheel Audio Controls . . . . . . . . . . . . . . .208 Steering Wheel Mounted Sound System Controls . . .208 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .400 Storage, Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . .220 Storing Your Vehicle . . . . . . . . . . . . . . . . . . . . . . .400 Stuck, Freeing . . . . . . . . . . . . . . . . . . . . . . . . . . . .342 Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 Supplemental Restraint System - Airbag . . . . . . . . . .39 Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . .362 Temperature Control, Automatic (ATC) . . . . . . . . . .213 Temperature Gauge, Engine Coolant . . . . . . . . . . . .312 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . . .117 Tire and Loading Information Placard . . . . . . . . . . .268 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . .261 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . . .283 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . .273 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .286 Changing . . . . . . . . . . . . . . . . . Compact Spare . . . . . . . . . . . . . General Information . . . . . . . . . High Speed . . . . . . . . . . . . . . . Inflation Pressures . . . . . . . . . . . Jacking . . . . . . . . . . . . . . . . . . . Life of Tires . . . . . . . . . . . . . . . Load Capacity . . . . . . . . . . . . . Pressure Monitor System (TPMS) Pressure Warning Light . . . . . . . Quality Grading . . . . . . . . . . . . Radial . . . . . . . . . . . . . . . . . . . Replacement . . . . . . . . . . . . . . . Rotation . . . . . . . . . . . . . . . . . . Safety . . . . . . . . . . . . . . . . . . . Sizes . . . . . . . . . . . . . . . . . . . . Snow Tires . . . . . . . . . . . . . . . . Spinning . . . . . . . . . . . . . . . . . Tread Wear Indicators . . . . . . . . I nf or mat i onPr ovi dedby: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .324 .280 .273 .276 .275 .324 .283 .268 .288 .145 .426 .276 .284 .287 .261 .262 .278 .282 .283 INDEX 443 Tire Safety Information . . . . . . . . . . . . . . . . . . . . .261 Tire Service Kit . . . . . . . . . . . . . . . . . . . . . . . . . . .312 To Open Hood . . . . . . . . . . . . . . . . . . . . . . . . . . .106 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .305 Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . . . .345 Recreational . . . . . . . . . . . . . . . . . . . . . . . . . . .306 Towing Vehicle Behind a Motorhome . . . . . . . . . . .306 Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .244 Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . .255 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . .305 Transaxle Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . .384 Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .233 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .384 Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 Transmitter Battery Service (Remote Keyless Entry) . .16 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . . .74 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . . .283 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 UCI Connector . . . . . . . . . . . . . . . . . . . . . . . . . . .207 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . .426 Universal Consumer Interface (UCI) Connector . . . .207 Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . .298 Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . . .33 Vehicle Vehicle Vehicle Vehicle Identification Number (VIN) . . . . . . . . . . . . .7 Loading . . . . . . . . . . . . . . . . . . . . . . . . . .269 Modifications/Alterations . . . . . . . . . . . . . . .8 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . .220 Warning Lights (Instrument Cluster Description) . . .145 Warnings and Cautions. . . . . . . . . . . . . . . . . . . . . . .7 Warranty Information . . . . . . . . . . . . . . . . . . . . . . . .4 Washer Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .372 I nf or mat i onPr ovi dedby: 10 444 INDEX Washers, Windshield . . . . . . . . . . . . . . . . . . . . . . .113 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .386 Water Driving Through . . . . . . . . . . . . . . . . . . . . . . . .245 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . .388 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . .388 Wind Buffeting. . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . .219 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Windshield Defroster . . . . . . . . . . . . . . . . . . . . . . .77 Windshield Washers . . . . . . . . . . . . . . . . . . . . . . .113 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . . .369 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . .113 Wiper Blade Replacement . . . . . . . . . . . . . . . . . . .369 I nf or mat i onPr ovi dedby: VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated nondrinking driver, call a cab, a friend, or use public transportation. WARNING! Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive. This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle. Chrysler Group LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured. FIAT is a registered trademark of Fiat Group Marketing & Corporate Communication S.p.A., used under license by Chrysler Group LLC. Copyright © 2014 Chrysler Group LLC INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible. The negative power connection should be made to body sheet metal adjacent to the negative battery connection. This connection should not be fused. Antennas for two-way radios should be mounted on the roof or the rear area of the vehicle. Care should be used in mounting antennas with magnet bases. Magnets may affect the accuracy or operation of the compass on vehicles so equipped. The antenna cable should be as short as practical and routed away from the vehicle wiring when possible. Use only fully shielded coaxial cable. Carefully match the antenna and cable to the radio to ensure a low Standing Wave Ratio (SWR). Mobile radio equipment with output power greater than normal may require special precautions. All installations should be checked for possible interference between the communications equipment and the vehicle’s electronic systems. I nf or mat i onPr ovi dedby: 2015 FIAT 500 2015 OWNER’S MANUAL Chrysler Group LLC 15FF500-126-AB Second Edition Rev 1 I nf or mat i onPr ovi dedby: Printed in U.S.A. FIAT 500