Honda - Odyssey - Owners Manual - 2008 - 2008

3950 NW 120th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NNG-Honda 8 Navigation interface for select Honda vehicles NTV-KIT582 NTV-DOC220 NTV-DOC220 Installation Guide Navigation Honda 8" Honda Odyssey Dash Removal setup MAP PAth Touch Screen Calibration FAQ Basic Trouble Shoot Remove side panel Remove 3 screws Remove AC Vent Panel Take out Screen Remove 4 screws Take out LCD Panel Get ready to place 1. video board 2. touch screen panel Installation Guide NTV-DOC582 Navigation Honda 8" Honda Pilot Dash Removal Remove AC Vent Remove 4 Screws Remove top panel (pulling out with tools) Remove 4 screws Take out LCD Panel Get ready to place 1. video board 2. touch screen panel Installation Guide NTV-DOC582 Navigation Honda 8" Install Touch Screen Panel Board Remove Front Bezel Use pick tools to remove LCD Casing unscrew factory video board and get ready to take off LCD panel Remove Video Board screws and 2 ribbon cable Place Touch Screen Panel on in fron the LCD Panel Installation Guide NTV-DOC582 Navigation Honda 8" Install Touch Screen Panel Board (II) Restore LCD Panel Install touch panel Look at the provided Label to define front/back side Restore 3 Ribbon cable connections #2 Video Ribbon #3) Touch Screen Ribbon #1 Small Ribbon for LCD panel Power Restore factory LCD Board Get ready for install daugther video board Installation Guide NTV-DOC220 Navigation Honda 8" Install Video Board Place the provided 3 Studs into these location 1) Place Y-Connection on the Ribbon Cable - Factory Brown Ribbon go to daugther Board - Daugther board ribbon go to factory board 2) Place Touch Screen Ribbon into daugther board MAKE SURE SOCKET ARE ALIGNED and CLOSED Installation Guide NTV-DOC220 Navigation Honda 8" Install Video Board II Restore 3 factory screws into daugther board Get the Panel casing Go thru video cable from interface module to the daugther board Peel off Metal Tape Secure video connection Installation Guide NTV-DOC220 Navigation Honda 8" Install Video Board III Close LCD panel casing, get ready to install interface/GPS module Remove Protection Plastic Bezel *picture shown as odyssey, for pilot, remain the same procedure NTV-DOC220 Installation Guide Navigation Honda 8" Overall Wiring Connection Figure Main Harness: 32P Screen Harness = To Screen and Car Side 8P Power Connector = To GPS box Harness Interface box: LCD (PINK) = To Interface box TP IN (Yellow) = To Interface box 12P Main Harness = To Screen and Car Side, GPS Harness = Interface box NAVI_IN, GPS Box 20P GPS Harness = GPS power to 12P Main Harness External Switch = Manual Switch for Radio/GPS Mode External Speaker and GPS Antenna DIP SW SETTING DIP SW Setting 1 ON --OEM CAMERA or No Camera 1 OFF- AFTER MARKET CAMERA 2 -5 OFF 6 OFF 7 OFF 8 OFF RGB ONLY RGB ONLY NTV-DOC220 Installation Guide Navigation Honda 8" Connect Reverse Wire To connect OEM Camera #1) DIP SW #1 ON #2) Connect reverse wire Honda Odyssey Honda Odyssey with OEM camera 1) Under driver side fuse box 2) Left green connector 3) Brown wire (reverse wire) 4) Tab the brown wire into Reverse wire (orange) Honda Pilot Honda Pilot with OEM camera 1) At the passenger side open Kick panel and find blue connector. 2) Tab the orange wire into interface box Reverse wire (orange) Please note that reverse wire might locate differently, above information is for reference only. You may find reverse wire at other location and connect it to the interface box reverse wire (orange) To connect Aftermarket Camera #1) DIP SW #1 OFF (reset power everytime change dip sw) #2) Connect reverse trigger to interface box orange reverse wire #3) Connect RCA Camera input to the interface box WEAK /NO GPS SIGNAL? Tips to Improve GPS Antenna Signal if vehicle equipped Metallized Windshield* “GPS MONITOR Tools” Exit IGO MAP by press SHUT DOWN BUTTON Console> SETUP GPS MONITOR Locate the Antenna with minimum 5 bars in dark blue or Gray bar (Always suggest mounting the GPS antenna on the roof) Press “!” icon to reset GPS signal and change the Antenna position PROPER GPS ANTENNA POSITION if vehicle equipped *Metallized Windshield SUV/Coupe Sedan TRUCK (Shown as Tundra) Alternatively, installer might choose to mount Antenna inside the headliner or inside vehicle using GPS monitor tools (see instruction). However, stay away from the windshield. * Windshields with metal particles can interfere with radio waves, dash-mount satellite radio receivers, and GPS receivers may be affected external transmitters and receivers may be required. IGO PRIMO MAP PATH SETTING 1. Press Setup ‐> Navigate Setup 2. Press on the Folder Icon 3. Select the following path in Storage Card ‐> cyb_navi.exe 4. Press HOME button on the top left corner and press NAVIGATION 5. System should able to run into “IGO PRIMO”