Honda - HR-V - Parts Catalogue - 2020 - 2020

www.collegehillshonda.com Accessory INSTALLATION INSTRUCTIONS PARTS LIST Application Publications No. VERSION 1 FOG LIGHTS P/N 08V31-T7A-100 2020 HR-V Issue Date SEP 2019 Combination light switch Right fog light (Identification mark: RH) Relay Left fog light (Identification mark: LH) 13 Wire ties Right fog light trim 4 Self-tapping screws Left fog light trim Fuse label Switch harness 15A Fuse Fog light harness © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII12705-21 (1909) 08V31-T7A-1000-90 1 of 19 www.collegehillshonda.com 2 Aluminum tapes Illustration of the Fog Lights Installed on the Vehicle RELAY 4 SWITCH HARNESS COMBINATION LIGHT SWITCH Long wire ties Clip (May not be used) RIGHT FOG LIGHT 15A FUSE FOG LIGHT HARNESS LEFT  FOG LIGHT INSTALLATION Ground bolt Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” TOOLS AND SUPPLIES REQUIRED 1. Disconnect the negative cable from the battery. Phillips screwdriver Ratchet 10 mm Socket Diagonal cutters Blanket Masking tape Isopropyl alcohol Shop towel Tape measure The following tools are available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857. • Plastic Trim Tool (T/N SILTRIMTL10) • Trim Tool Set (T/N SOJATP2014) 2 of 19 AII12705-21 (1909) © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 2. Lower the steering wheel. Apply masking tape to the upper column cover as shown. 4. Turn the steering wheel 180° counterclockwise. Using a plastic trim tool, release the upper column cover. STEERING WHEEL UPPER COLUMN COVER MASKING TAPE UPPER COLUMN COVER PLASTIC TRIM TOOL RETAINING TAB QD41004AJ QD41002AJ 3. 5. Turn the steering wheel 90° clockwise. Using a plastic trim tool, release the upper column cover. Remove the upper column cover. UPPER COLUMN COVER 4 RETAINING TABS UPPER COLUMN COVER RETAINING TAB QD41005AJ PLASTIC TRIM TOOL © 2019 American Honda Motor Co., Inc. – All Rights Reserved. QD41003AJ AII12705-21 (1909) 3 of 19 www.collegehillshonda.com 6. Remove the self-tapping screw from the lower column cover. 8. Pull away the door opening seal, and remove the driver’s dashboard side lid. DOOR OPENING SEAL (Pull away.) LOWER COLUMN COVER 7. SELF-TAPPING SCREW 6 RETAINING TABS QD41006AJ DRIVER’S DASHBOAR D SIDE LID PLASTIC TRIM TOOL Turn the steering wheel 180° clockwise, and remove the self-tapping screw from the lower column cover. 9. LOWER COLUMN COVER Apply masking tape to the lower column cover. SELF-TAPPING SCREW QD41007AJ LOWER COLUMN COVER 4 of 19 QD40315AJ AII12705-21 (1909) MASKING TAPE QD40316AJ © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 10. Pull away the door opening seal. Remove the driver’s dashboard lower cover, and unplug the vehicle connectors. 12. Remove the front bumper: • Wrap a shop towel around the lever. • Apply masking tape as shown. DOOR OPENING SEAL (Pull away.) VEHICLE CONNECTORS 11 CLIPS SHOP TOWEL LEVER CLIP DRIVER’S DASHBOARD LOWER COVER QD41009AJ 11. Remove the lower column cover. HEADLIGHT FRONT FENDER MASKING TAPES FRONT BUMPER SELF-TAPPING SCREW LOWER COLUMN COVER © 2019 American Honda Motor Co., Inc. – All Rights Reserved. QD41402AJ AII12705-21 (1909) 5 of 19 www.collegehillshonda.com • Remove the front grille cover. • Remove the two self-tapping screws and four clips on each side. FRONT GRILLE COVER LEFT FRONT  WHEEL ARCH PROTECTOR 9 CLIPS 2 SELF-TAPPING SCREWS 4 CLIPS • Remove the 12 clips. • 12 CLIPS Remove the front wheel arch protector on each side. 5 CLIPS 2 CLIPS LEFT FRONT  WHEEL  ARCH PROTECTOR Remove the clips from the front in order. BOTTOM VIEW 11 CLIPS RETAINING TAB (Remove first.) 6 of 19 AII12705-21 (1909) FRONT BUMPER LEFT SIDE SILL TRIM © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com • Remove the self-tapping screw on each side. • Release the five retaining tabs on each side, in the order shown. 1 3 RETAINING TABS SELF-TAPPING SCREW 2 2 RETAINING TABS © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII12705-21 (1909) FRONT BUMPER 7 of 19 www.collegehillshonda.com • With the help of an assistant, remove the front bumper. • Place the front bumper on a blanket. Installing the Fog Lights 13. Remove the left bumper trim. LEFT BUMPER TRIM (Do not reuse.) 2 RETAINING TABS FRONT BUMPER (inside) LEFT BUMPER TRIM 9 RETAINING TABS FRONT BUMPER 14. Install the left fog light to the left fog light trim with two self-tapping screws. NOTE: Check that the back of the fog light has the correct identification mark before installation. LEFT FOG LIGHT TRIM LEFT FOG LIGHT (Identification mark: LH) 8 of 19 AII12705-21 (1909) 2 SELF-TAPPING SCREWS © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 15. Install the left fog light trim to the front bumper with nine retaining tabs. FRONT BUMPER (inside) Routing the Fog Light Harness 17. Route the fog light harness as shown. LEFT FOG LIGHT TRIM WASHER TUBE RIGHT HEADLIGHT 9 RETAINING TABS 16. Repeat steps 13 thru 15 for the other side. WASHER FOG LIGHT TUBE HARNESS (Route behind  the washer tube.) FOG LIGHT HARNESS 1-PIN CONNECTOR VEHICLE 1-PIN CONNECTOR 18. Plug the vehicle 1-pin connector into the fog light harness 1-pin connector. © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII12705-21 (1909) 9 of 19 www.collegehillshonda.com 19. Secure the 1-pin connectors to the vehicle harness with one wire tie. 21. Secure the fog light harness to the vehicle harness with one wire tie. VEHICLE HARNESS 1-PIN CONNECTORS VEHICLE HARNESS WIRE TIE RIGHT HEADLIGHT WIRE TIE FOG LIGHT HARNESS FOG LIGHT HARNESS 20. Route the fog light harness as shown. Install the fog light harness ground terminal to the vehicle panel with one ground bolt. 22. Line up the branch of fog light harness with the branch of vehicle harness, and secure the fog light harness to the vehicle harness with three wire ties. 3 WIRE TIES WASHER TUBE VEHICLE HARNESS BRANCH OF VEHICLE HARNESS VEHICLE PANEL FOG LIGHT HARNESS FOG LIGHT HARNESS (Route behind the washer tube.) BRANCH OF FOG LIGHT HARNESS QD42010BH GROUND BOLT FOG LIGHT HARNESS GROUND TERMINAL 10 of 19 AII12705-21 (1909) © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 23. Secure the fog light harness clip to the hole in the vehicle frame as shown. FOG LIGHT HARNESS CLIP 25. Secure the fog light harness to the vehicle harness with one wire tie. FRONT BUMPER BEAM FRONT BUMPER BEAM VEHICLE FRAME VEHICLE HARNESS FOG LIGHT HARNESS WIRE TIE QD42011AH If the vehicle is equipped with another accessory harness, go to step 27; otherwise, continue with step 24. FOG LIGHT HARNESS 26. Connect two long wire ties together, and secure the fog light harness to the front bumper beam with them. Go to step 32. Without Another Accessory Harness 24. Route the fog light harness as shown. Secure the fog light harness clip to the hole in the vehicle frame as shown. FRONT BUMPER BEAM FOG LIGHT HARNESS CLIP VEHICLE FRAME FRONT BUMPER BEAM 2 LONG WIRE TIES (Joint.) 2 JOINTED LONG WIRE TIES FRONT BUMPER BEAM FOG LIGHT HARNESS QD42014AH FOG LIGHT HARNESS © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII12705-21 (1909) 11 of 19 www.collegehillshonda.com With Another Accessory Harness 30. Secure the fog light harness to the vehicle harness with one wire tie and one long wire tie as shown. 27. Route the fog light harness as shown. FOG LIGHT HARNESS FRONT BUMPER BEAM FOG LIGHT HARNESS CLIP (Cut off.) VEHICLE HARNESS OTHER ACCESSORY HRNESS FRONT BUMPER BEAM LONG WIRE TIE WIRE TIE FOG LIGHT HARNESS 520 mm (20.47 in.) LONG WIRE TIE 31. Connect two long wire ties together, and secure the fog light harness to the front bumper beam with them. FOG LIGHT HARNESS FOG LIGHT HARNESS 2-PIN CONNECTOR 28. Using diagonal cutters, cut off the fog light harness clip. NOTE: Be careful not to damage the fog light harness. 29. Secure the fog light harness to the other accessory harness with one long wire tie as shown. FRONT BUMPER BEAM 2 LONG WIRE TIES (Joint.) 12 of 19 AII12705-21 (1909) JOINTED LONG WIRE TIE FRONT BUMPER BEAM FOG LIGHT HARNESS © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 32. Using isopropyl alcohol on a shop towel, thoroughly clean the front bumper beam where the aluminum tape will attach. Routing the Switch Harness 35. Install the relay to the switch harness relay block. RELAY FRONT BUMPER BEAM SWITCH HARNESS RELAY BLOCK FRONT BUMPER BEAM ALUMINUM TAPE Clean with isopropyl alcohol. FOG LIGHT HARNESS QD42017BH QD42015AH 36. Plug the switch harness 1-pin connector into the vehicle 1-pin connector. 33. Secure the fog light harness to the front bumper beam with two pieces of aluminum tape as shown. 34. With the help of an assistant, bring the front bumper close to the vehicle, and plug the two fog light harness 2-pin connectors into the right and left fog light. Install the front bumper. SWITCH HARNESS 1-PIN CONNECTOR VEHICLE 1-PIN CONNECTOR DRIVER’S DASHBOARD LOWER COVER OPENING 2 FOG LIGHT HARNESS 2-PIN CONNECTORS STEERING SHAFT RIGHT  FOG LIGHT FRONT BUMPER LEFT  FOG LIGHT © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII12705-21 (1909) 13 of 19 www.collegehillshonda.com 37. Install the clip to the switch harness relay block. Secure the switch harness relay block to the hole in the vehicle frame. If another relay block is already secured to the hole in the vehicle frame, secure the switch harness relay block to that relay block. 38. Line up the branch of the switch harness with the branch of the vehicle harness, and secure the switch harness to the vehicle harness with two wire ties. BRANCH OF VEHICLE HARNESS VEHICLE FRAME DRIVER’S DASHBOARD LOWER COVER OPENING 2 WIRE TIES SWITCH HARNESS RELAY BLOCK CLIP SWITCH HARNESS VEHICLE HARNESS SWITCH HARNESS RELAY BLOCK WITH OTHER  RELAY BLOCK DRIVER’S DASHBOARD LOWER COVER OPENING BRANCH OF SWITCH HARNESS 39. Secure the switch harness to the vehicle harness with three wire ties. SWITCH HARNESS VEHICLE HARNESS 3 WIRE TIES OTHER  RELAY BLOCK DRIVER’S DASHBOARD LOWER COVER OPENING 14 of 19 AII12705-21 (1909) © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 40. Secure the switch harness to the vehicle harness with one wire tie. VEHICLE HARNESS WIRE TIE DRIVER’S DASHBOARD LOWER COVER OPENING With Another Accessory Harness 4-pin Connector 42. If another accessory harness 4-pin connector is plugged into the fuse box, plug the switch harness 4pin connector into that accessory harness 4-pin connector. FRONT VIEW OTHER ACCESSORY HARNESS  4-PIN CONNECTOR OTHER ACCESSORY HARNESS 4-PIN CONNECTOR FUSE BOX SWITCH HARNESS  4-PIN CONNECTOR SWITCH HARNESS If the vehicle is equipped with another accessory harness 4-pin connector, go to step 42; otherwise, continue with step 41. DRIVER’S DASHBOARD LOWER COVER OPENING Without Another Accessory Harness 4-pin Connector 41. Plug the switch harness 4-pin connector into the fuse box. Go to step 43. FRONT VIEW Plug in here. FUSE BOX SWITCH HARNESS  4-PIN CONNECTOR DRIVER’S DASHBOARD LOWER COVER OPENING © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII12705-21 (1909) 15 of 19 www.collegehillshonda.com If the vehicle is equipped with another accessory harness 8-pin connector, go to step 44; otherwise, continue with step 43. Without Another Accessory Harness 8-pin Connector With Another Accessory Harness 8-pin Connector 44. If another accessory harness 8-pin connector is plugged into the fuse box, unplug it from fuse box. Plug the other accessory harness 8-pin connector into the switch harness 8-pin connector. 43. Plug the switch harness 8-pin connector into the fuse box. Go to step 46. FRONT VIEW OTHER ACCESSORY HARNESS  8-PIN CONNECTOR FRONT VIEW Plug in here. DRIVER’S DASHBOARD LOWER COVER OPENING SWITCH HARNESS 8-PIN CONNECTOR FUSE BOX OTHER ACCESSORY HARNESS  8-PIN CONNECTOR FUSE BOX SWITCH HARNESS 8-PIN CONNECTOR DRIVER’S DASHBOARD LOWER COVER OPENING 45. Plug the switch harness 8-pin connector into the fuse box. FRONT VIEW Plug in here. SWITCH HARNESS 8-PIN CONNECTOR FUSE BOX DRIVER’S DASHBOARD LOWER COVER OPENING 16 of 19 AII12705-21 (1909) © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 46. Secure the switch harness to the vehicle harness with one wire tie. VEHICLE HARNESS SWITCH HARNESS DRIVER’S DASHBOARD LOWER COVER OPENING 49. Install the new combination light switch to the steering column.  NOTE: Do not push on the lever when installing the switch. Incorrect. WIRE TIE STEERING WHEEL Do not push on the lever. VEHICLE CONNECTOR QD42028AH 47. Unplug the vehicle connector from the combination light switch. Incorrect. NEW COMBINATION LIGHT SWITCH STEERING WHEEL 50. Plug the vehicle connector into the new combination light switch. 51. Plug the 15A fuse into the fuse box. Do not pull on the lever. VEHICLE CONNECTOR COMBINATION LIGHT SWITCH (Do not reuse.) 2 RETAINING TABS (Push.) DRIVER’S DASHBOARD LOWER COVER OPENING CONNECTING LOCATION FRONT VIEW 2 RETAINING TABS (Push.) 48. While pushing the two retaining tabs, slide the combination light switch out and remove it from the steering column.  NOTE: Do not pull on the lever when removing the switch. © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII12705-21 (1909) 15A FUSE FUSE BOX QD42031AH 17 of 19 www.collegehillshonda.com 52. Using isopropyl alcohol on a shop towel, clean the lower column cover where the fuse label will attach. 55. Using isopropyl alcohol on a shop towel, clean the relay box cover. FUSE LABEL ATTACHING ATTACHING FUSE LABEL (15A OPTION FUSE) RELAY BOX COVER LOWER  COLUMN COVER Clean with isopropyl alcohol. Clean with isopropyl alcohol. QC33139CH QC51302BH 56. Attach the fuse label to the relay box cover. 53. Attach the fuse label to the lower column cover. 57. Check that all wire harnesses are routed properly and all connectors are plugged in. 54. Remove the relay box cover. 58. Install all removed parts. 3 RETAINING TABS 59. Connect the negative cable to the battery. 60. Press and hold the audio unit power button for 2 seconds to restore radio and navi (if equipped) system functions. RELAY BOX COVER 61. Set the clock on vehicles without navigation. 62. If necessary, restore the systems back to normal operation as described in the service information. RELAY BOX 18 of 19 QD42032AH AII12705-21 (1909) © 2019 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com Check the Operation of the Fog Lights 63. Make sure the fog lights operate as described in the vehicle owner’s manual. How to Aim the Fog Lights 64. Adjust the fog light aim by turning the adjustment screw in or out until the correct aim is obtained. Adjust the aim according to local laws and regulations.  NOTE: The fog light lenses may cloud when the outside temperature is cold; this is normal and should go away in warm weather. LEFT  FOG LIGHT PHILLIPS SCREWDRIVER ADJUSTMENT SCREW BULB REPLACEMENT NOTE: Perform bulb replacement by referring to the vehicle owner’s manual. © 2019 American Honda Motor Co., Inc. – All Rights Reserved. AII12705-21 (1909) 19 of 19