Toyota - 4 Runner - Parts Catalogue - 2011 - 2011

31367 TOYOTA FJ CRUISER & 4 RUNNER INCLUDING TRAIL EDITION 6/6/2011 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 3,500 LBS. TRAILER WEIGHT & 350 LBS. TONGUE WEIGHT. GROSS LOAD CAPACITY WHEN USED AS STRAIGHT LINE PULL: 9,000 LBS. MAX. LINE PULL. DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** Parts List ITEM QTY PART NUMBER DESCRIPTION 1 2 5/8-11 x 1 3/4 CARRIAGE BOLT DRIVER SIDE FRAME RAIL 2 2 5/8-11 HEX FLANGE NUT 3 2 CM-31367-SP .250 x 1.50 x 3.00" SQUARE HOLE SPACER FRAME CROSS MEMBER TOW LOOP 3 PASSENGER SIDE FRAME RAIL 2 EXISTING FRAME STUDS AND FLANGE NUTS USE EXISTING HEX FLANGE NUTS REMOVE LOWER NUT ON THIS SIDE AND NUT FROM INSIDE (BOTH SIDES) 1 HITCH WEIGHT: 33 LBS. PASS BOLT THROUGH AND INTO POSITION INSTALL TIME: 30 MINUTES INSTALL NOTES: - NO DRILLING REQUIRED INSTALLATION STEPS 1) Remove hex flange nuts from end of frame rail (lowest 2 on each side) as shown above. Re-use in step 4. 2) Lift hitch into position, locating the vehicle tow loop brackets under the hitch mounting plates. 3) Insert 5/8" bolts through the front plates and into position through the tow loops. 4) Loosely install 5/8" nuts and supplied spacers then reinstall the flange nuts removed in step 1. 5) Torque all 10mm fasteners to 37 lb-ft and all 5/8" fasteners to 150 lb-ft. PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND. Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage. 31367 TOYOTA FJ CRUISER & 4 RUNNER ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***. FRONT MOUNTED ACCESSORIES 1) Do not exceed front axle Gross Weight Rating (GAWR). Consult owners manual or specification plate located on driver's door frame. Measure gross front axle weight by placing front wheels of loaded vehicle on a scale. WARNING: Exceeding GAWR may overload the front axle and/or suspension. This could result in accident, property damage and personal injury. 2) Reposition front mounted license plate if obstructed. 3) Do not obstruct vehicle lights. 4) Allow free air flow into grille opening. 5) Rear wheel traction may be reduced. This could effect handling. Reduce speed and drive with caution. 6) Accessories extend front of vehicle. This may reduce approach angle. Use caution when parking and maneuvering. 7) Do not obstruct driver view. VEHICLE RECOVERY AND WINCHING TIPS 1) Use OEM tow hooks, recovery eyes or a clevis mount for attachment of a tow strap or winch cable. WARNING: NEVER use a ball and/or ball mount as an anchor point for tow strap or winch cable. Severe personal injury or death could result. 2) Observe winch manufacturer's recommendations, cautions and warnings. 3) Attach return cable to tow hook or recovery eye when using a snatch block (See figure 1). CAUTION: Do not attach return cable to winch mount. This may overload winch mount and/or front mounted receiver. TREE SAVER STRAP CABLE DAMPING TOWELS OR JACKETS. SOLID OBJECT SNATCH BLOCK RETURN CABLE TOW HOOK OR RECOVERY EYE RATING FIGURE 1 For Maximum line pull rating, winch cable must not exceed: - 15 degree angle up or down from horizontal (See Figure 2). - 45 degree angle left or right from straight ahead (See Figure 3). CAUTION: Exceeding the maximum line pull rating may over load winch, winch mount, and/or front mounted receiver. FIGURE 2 FIGURE 3 Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.